Casio Xj 360 Dlp Users Guide

							11
Projection Operations
The color mode setting lets you specify the type of image you will be projecting, so the 
projector can optimize image color.
To change the color mode setting
1.Press the [COLOR MODE] key.
zThis causes the color mode screen to appear on the projection image. The z mark 
indicates the current color mode setting.
zFor details about each of the settings, see “Image Adjustment J Color Mode” on 
page 28.
2.Use the [S] and [T] keys to move the cursor to the setting you want, 
and then press the [ENTER] key.
zThis moves the z to item that is selected by the cursor, and applies the setting to the 
image.
3.To close the setup screen, move the cursor to “Close”, and then press 
the [ENTER] key.
zYou can also close the setup screen by pressing the [ESC] or [COLOR MODE] key.
Using Color Mode (COLOR MODE)
Downloaded From projector-manual.com Casio Manuals 
						

							Projection Operations
12
You can use the remote controller keys to adjust the volume level of the audio that is output 
from the projector’s speaker.
To adjust the volume level
1.On the remote controller, press the [VOL +] or [VOL –] key.
zThis causes the [Volume] screen to appear on the projected image.
2.Press the [VOL +] key or the [X] key to increase the volume, or the 
[VOL –] or [W] key to lower the volume.
3.To close the setup screen, move the cursor to “Close”, and then press 
the [ENTER] key.
zYou can also close the setup screen by pressing the [ESC] key.
The mute function causes the projected image to go to black screen, and stop output of the 
audio from the speaker.
To mute the image and audio
1.On the remote controller, press the [MUTE] key.
zThis causes the projected image to go to a black screen, and stops output from the 
speaker.
2.To restore the image and audio, press the [MUTE] key again or press 
the [ESC] key.
Adjusting the Volume Level (VOL +/–)
Muting the Image and Audio (MUTE)
Downloaded From projector-manual.com Casio Manuals 
						

							13
Projection Operations
You can use the remote controller’s zoom keys to enlarge a specific part of the projected 
image.
To enlarge part of the projected image
1.On the remote controller, press the [D-ZOOM +] or [D-ZOOM –] key.
zThis causes a cross cursor ( ) to appear on the projected image.
2.Use the remote controller’s cursor keys to move the cross cursor to the 
part of the image that you want in the center of the enlarged image.
3.On the remote controller, press the [D-ZOOM +] key to enlarge the 
image.
zEach press of the [D-ZOOM +] key enlarges the image one step. Pressing the 
[D-ZOOM +] key will not affect the image if it is already its maximum size.
zYou can back step through the image enlargements by pressing the [D-ZOOM –] key.
z
Yo u can shift the zoomed image up, down, left, or right by pressing the applicable 
remote controller cursor key.
4.To exit image enlargement and return the image to its original size, 
press the remote controller’s [ESC] key.
Enlarging the Projected Image (D-ZOOM +/–)
Downloaded From projector-manual.com Casio Manuals 
						

							Projection Operations
14
The freeze function stores the current projected image in projector memory, and projects it as 
a still image.
To freeze the projected image
1.On the remote controller, press the [FREEZE] key.
zThis freezes the image that was being projected when you pressed the [FREEZE] key.
2.To unfreeze the image, press the [FREEZE] key again or press the 
[ESC] key.
Use the procedures in this section to display the pointer and to select its shape (arrow, bar). 
You can use the pointer to point to a specific location of the projected image during a 
presentation.
To display the pointer 
Press the [POINTER/SELECT] key to display the pointer in the projected image.
The following operations can be performed while the pointer is displayed.
zPressing the [STYLE] key (the [ENTER] key functions as the [STYLE] key while the 
pointer is displayed) rotates the pointer, causes it to blink, etc. If you are using an arrow 
pointer, for example, each press of the [STYLE] key cycles through four different pointer 
orientations.
zThe cursor keys can be used to move pointer around the image. Holding down a cursor 
key moves the pointer at high speed.
Freezing the Projected Image (FREEZE)
Displaying the Pointer
Downloaded From projector-manual.com Casio Manuals 
						

							15
Projection Operations
Selecting the Pointer Shape
Each press of the [POINTER/SELECT] key while the pointer is displayed cycles through the 
pointer shapes in the sequence shown below.
To clear the pointer from the image
Press the [ESC] key.
Downloaded From projector-manual.com Casio Manuals 
						

							Using the Setup Menu
16
Using  the  Setup Menu
Pressing the [MENU] key while an image is being projected displays the setup menu on the 
projected image. The setup menu can be used to configure a variety of different projector 
settings. The following table shows the menu items that are available in the Setup Menu.
Setup Menu Overview
Main menu Sub-menu Sub-menu Item Type ∗1Input source ∗2
See page
RCS V–
Image 
Adjustment Brightness Value Setting 27
Contrast Value Setting 27
Sharpness Value Setting 27
Saturation Value Setting 27
Tint Value Setting∗3∗327
Color Mode Setting Screen 28
Color Balance Setting Screen 28
Restore Menu Defaults Execution 29
Signal 
SettingsVertical Position Value Setting 30
Horizontal Position Value Setting 30
Frequency Value Setting 30
Phase Value Setting 30
Noise Filter Selection 31
Restore Menu Defaults Execution 31
Screen 
SettingsKeystone Correction Value Setting 31
Aspect Ratio Selection∗432
Resize Image To Fit Selection 33
Projection Mode Selection 34
Ceiling Mount
 ∗11 Selection 34
Restore Menu Defaults Execution 35
∗1 This is the sub-menu item type. Refer to the pages noted below for more information.
Value Setting:Specifies a numeric value () page 22).
Selection:Allows selection from multiple options () page 22).
Setting Screen:Numeric value specification or option selection on a separate setting 
screen () page 23).
Execution:Initializes a setting () page 24).
Information:Displays information only () page 24).
∗2 These columns indicate whether each item appears ( ) or not ( ) for each input 
source (R = RGB, C = Component, S = S-VIDEO, V = Video, – = No input signal).
∗3 This setting can be configured only for an NTSC or NTSC4.43 signal.
∗4 This setting can be selected only when the aspect ratio of the input signal is 4:3.
Downloaded From projector-manual.com Casio Manuals 
						

							17
Using the Setup Menu
Main menu Sub-menu Sub-menu Item TypeInput source
See page
RCS V–
Detailed 
SettingsVo l u m e Va l u e  S e t t i n g*535
Pointer Selection 36
Low-noise Mode Selection∗
11∗11∗11∗11∗1136
Power On Password Special∗10 37
Change Password Special∗10 37
Advanced Settings 1
Auto Input Detect Selection 40
Auto Keystone 
CorrectionSelection 40
Auto Adjust Selection∗641
Show Screen Text Selection 41
Startup Screen Selection 42
No Signal Screen Selection 42
Advanced Settings 2
Auto Power Off Selection 43
RGB Input Setting Screen∗744
Video Signal Setting Screen∗845
S-Video Signal Setting Screen∗945
Image Enhancement 1 Selection 45
Image Enhancement 2 Selection 45
Language Setting Screen 46
Restore Menu Defaults Execution 46
Operational 
InfoLamp Time Information 46
Input Signal Information 46
Signal Name Information 47
Resolution Information 47
Horizontal Frequency Information 47
Vertical Frequency Information 47
Scan System Information 47
Restore All Defaults Execution 47
Reset Lamp Time Execution 47
∗5 This setting is for the currently selected input source.
∗6 This setting can be configured only when the input source is RGB.
∗7 This setting can be configured only when the input source is RGB/Component.
∗8 This setting can be configured only when the input source is VIDEO.
∗9 This setting can be configured only when the input source is S-VIDEO.
∗10 This is a special sub-menu item that is different from other types.
∗11 The Low-noise Mode is available only when “Ceiling Mount” is turned off.
Downloaded From projector-manual.com Casio Manuals 
						

							Using the Setup Menu
18
Before Configuring Menu Settings
Always remember that the settings you configure on the setup menu are applied for the input 
source (RGB, Component, S-VIDEO, VIDEO) that was selected when you displayed the setup 
menu. Note the following important points.
zThe items that appear on the setup menu depend on the currently selected input source 
and other factors.
Some items apply to a certain specific input source, while some apply to multiple input 
sources.
zEven for menu items that are common to multiple input sources, the setting range or 
selectable options may differ according to the input source.
zWith certain exceptions, there are basically two types of settings that can be configured 
for multiple input sources. One type lets you configure different settings for each individual 
input source. The other type applies a single setting to all input sources. The volume 
level setting, for example, lets you configure a different setting for each input source, while 
the keystone correction setting lets you configure a single common setting for all input 
sources.
zFor details about how settings are saved, and other details, see “Setup Menu Reference” 
on page 27.
Downloaded From projector-manual.com Casio Manuals 
						

							19
Using the Setup Menu
This section explains projector operations you need to perform while configuring setup menu 
settings. It also provides details about each sub-menu item type.
Basic Setup Menu Operations
The following is the general flow of the steps you need to perform when configuring setup 
menu operations.
1.Select the input source whose settings you want to configure.
2.Press the [MENU] key.
zThis causes the setup menu screen to appear in the upper left corner of the projected 
image. At this time, only the main menu will be visible.
3.Press the [T] key.
zThis will highlight the “Image Adjustment” on the main menu, indicating that it is 
selected. Also, the “Image Adjustment” sub-menu will appear to the right.
zThe items that appear in the sub-menu depend on the input source you selected in 
step 1 and whether or not a signal is being input from the input source. For details, 
see “Setup Menu Overview” on page 16.
Setup Menu Screen Operations
Main menu
Sub-menu
Currently selected 
menu item
Downloaded From projector-manual.com Casio Manuals 
						

							Using the Setup Menu
20
4.Use the [S] and [T] keys to move the highlighting to the main menu 
item you want.
z The sub-menu for the currently selected main menu item will appear to the right.
5.Press the [X] key or the [ENTER] key.
zThis will cause the item at the top of the currently displayed sub-menu to become 
highlighted, indicating that it is selected.
6.Select the sub-menu item whose setting you want to change.
zUse the [S] and [T] keys to move the highlighting to the sub-menu item you want.
Configuring Advanced Settings 1 and Advanced Settings 2
The “Advanced Settings 1” and “Advanced Settings 2” sub-menus on the “Detailed Settings” 
main menu provide access to further sub-menus for configuring various advanced settings. 
Use the following steps to select items on the advanced settings sub-menus. 
(1) Use the [S] and [T] keys to move the highlighting to “Advanced Settings 1” or 
“Advanced Settings 2”.
(2) Press the [ENTER] key.
zThis closes the main menu and switches to one of the special sub-menus shown below.
(3) Use the [S] and [T] keys to move the highlighting to the sub-menu item you want.
Advanced Settings 1 Sub-menu Advanced Settings 2 Sub-menu
Downloaded From projector-manual.com Casio Manuals