Celluon Projector Picopro User Manual

c. Wireless Connection
Using Miracast : 
The Miracast capability is called different names on difference devices. ( i.e. Samsung/Sony = Screen Mirroring, HTC = Media Output)
Please find this in device settings.
1
3. After about 20-30 seconds, “Ready to Connect” screen for Miracast will display.
1. Turn on PicoPro by pressing the power button for about 2-3 seconds.
2. Celluon logo will display upon powering on, followed by a “Preparing 
wireless connection… To go to HDMI mode, press Mode Switch button”...

4. On a desired mobile device, find and select Screen Mirroring / Media Output.
5. Mobile device will search for nearby devices to connect.
4
* 
It is recommended to disconnect any previously connected WiFi network before attempting to connect via Miracast (screen mirroring).
6. When device discovers “Celluon PicoPro”, tap 
to connect. 7. Mobile device will say “Connected” 
and PicoPro will start mirroring display.
76
12 

1
1. Turn on PicoPro by pressing the power button for about 2-3 seconds.3. After about 20-30 seconds, “Ready to Connect” screen for Miracast will 
display. (Default wireless connection mode is Miracast)
2. Celluon logo will display upon powering on, followed by a “Preparing 
wireless connection… To go to HDMI mode, press Mode Switch button” 
screen.
23
Using DLNA : * 
To connect to a device using DLNA capability, you must install a DLNA streaming app on your mobile device. Applicable apps can be...

4. Lightly press “Mode Switch” button again to change to DLNA mode.
4
5. DLNA “Ready to Connect” screen will display upon completion of mode switch.
5
14 

6. On a desired mobile device, go to WiFi setting, and connect to “Celluon PicoPro”. 
Use password “12345670” to connect. 
8. When WiFi is successfully connected, open the installed DLNA streaming application 
on the mobile device.
9. Select desired content to display. 
10. Select display location: Celluon PicoPro.
11. Mobile device will say “Connected” and PicoPro will start display selected media contents.
*** For DLNA connection with iOS devices:
1. Follow above steps 1-11.6
15 

d. Switching Connection ModePicoPro allows you to easily switch from wired connection mode to wireless mode, and vice versa.
From HDMI mode to Miracast mode
1. From HDMI mode, press and hold Mode Switch button for about 2 seconds.
2. Celluon logo will display.
3. After the logo, “Preparing wireless connection… To go to HDMI mode, press Mode Switch button” screen will display.
4. After about 20-30 seconds, “Ready to Connect” screen will display for Miracast connection, indicating that the mode is...

8. Making Adjustments
Volume Adjustment*Volume is controlled directly from PicoPro.
Locate touch volume control area on top of device. Adjust the volume by lightly touching the + or – pattern.
Speaker / Earphone UsagePlease connect a speaker or an earphone to the 3.5mm audio out jack. 
Laser AlignmentWhen the images seem blurry and/or the colors appear skewed, please visit Celluon website at www.celluon.com for Laser Alignment instructions.
APC (Auto Power Control) SettingThis setting is to efficiently...

First three LED indicators remain solid. When charging at this stage, the fourth LED 
indicator will blink to indicate it is being charged.
All four LED indicators will remain solid.
100% charged
Volume control + & - sensors will blink to indicate low battery status
0% chargedDescription
Status
LED Indicator
75% charged First two LED indicators remain solid. When charging at this stage, the third LED 
indicator will blink to indicate it is being charged.
50% charged First LED indicator remains solid....

10. Troubleshooting
No signal when a device is connected via HDMI cablePlease make sure the cables are inserted into the correct port. Please note that different devices require different 
gender/adapter to convert to micro HDMI compatible.
Mobile device cannot find Celluon PicoPro during 
Miracast connection searchPlease make sure PicoPro is on Miracast mode. This may also be due to particularly heavy wireless traffic. If this 
is the case, please reset the device by pressing the reset button on the...

11. Specifications
The perceived brightness of laser projectors with a given ANSI 
brightness is 50%+ higher than that of the LED based projectors
Brightness
150  x 73  x 13.4 mm
(6 x 3 x 0.5 inches)
181g
( 0.4lbs )
3140mAh @ 3.7V
Size
Measurement
Weight
The operating time may slightly vary depending on the environment of use
Battery Capacity
Product Lifetime
Display Method
Aspect RatioThrow RatioSequential Contrast Ratio
Display PerformanceResolutionColor Depth
Battery Operation Time
Electrical...