Christie Digital Systems M Series User Manual
Have a look at the manual Christie Digital Systems M Series User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 267 Christie Digital Systems manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
M-Series User Manual6-5020-100009-01 Rev.1 (07/08) 6.1.12Pixel Defects 6.1.13Image Artifacts 6.1.14Picture Centering 6.2 FEATURE SET 6.2.1Airflow 6.2.2Air Filters (Optional) 6.2.3Dust Sealing Red 0 bright, 1 dark Green 0 bright, 0 dark Blue 0 bright, 2 dark non-adjacent Evaluate on multi-burst or fine grid test pattern No visible artifacts with observer at 1 full screen height from image 1080p centering error ±5% of vertical offset (32 pixels) SXGA+ centering error ±5% of vertical offset (26 pixels) Air intakes Right side of projector Air exhaust Hot lamp exhaust: rear of projector Cool light engine exhaust: left side of projector Filter media types Coarse foam filter Fog filter Filter access Service-interchangeable via access panel Dust sealed DMDs Gasket sealed Dust sealed illumination system Sealed from lamp input to entrance face of prism when lamps are installed
Section 6: Specifications M-Series User Manual6-6020-100009-01 Rev.1 (07/08) 6.2.4ILS (Intelligent Lens System) 6.2.5Projection Lens Compatibility 6.2.6Dynamic Iris Motorized lenses and lens mount with position encoding Zoom, focus, horizontal and vertical offsets Accuracy ±2 pixel Manual control 1/3 pixel fine movement control per button press on any applicable User Interface (e.g., remote). Calibration User Configurable Calibration Modes Automatic calibration on lens change detection Automatic calibration on power-up Manual calibration Calibration time < 10 secs when required Bore sight 3-point +- 4 degrees adjustment and lockable without removing covers Travel time stop to stop Zoom and Focus 10 sec nominal (depends on lens type) Offsets 5 sec (nominal (depends on lens type) Manual Lens Movement Manual over-ride permissible for zoom and focus Lens type Reverse Telecentric Internal-focus Motorized zoom and focus with position feedback Lens throw ratio Lens ILS 0.73:1SX+/0.67:1HD Lens ILS 1.25-1.6SX+/1.16-1.49HD Lens ILS 1.5-2.0SX+/1.4-1.8HD Lens ILS 2.0-2.8SX+/1.8-2.6HD Lens ILS 2.8-4.5SX+/2.6-4.1HD Lens ILS 4.5-7.5SX+/4.1-6.9HD Lens ILS 7.5-11.2SX+/6.9-10.4HD Lens ILS 1.2SX+/1.1HD Lens ILS 1.2SX+/1.1HD SFL Compatibility Easy Rider-type HD lenses with motor and mount change Lens change-out Clamp type tool-less mount with built-in connector Lens ID Each lens type is encoded with a unique ID code that is identified in the projector Motorized iris with position feedback Scene controlled motorized iris automatically adjusts to image content Max frequency open-close-open 20 Hz Sound level Within ambient noise level of projector Configurable per channel
M-Series User Manual6-7020-100009-01 Rev.1 (07/08) 6.2.7Automatic Fans 6.2.8Automatic Color Filtering 6.2.9Constant Lamp Output Management 6.2.10Shutter 6.2.11Lamps Temperature sensitive fan speed control Fans automatically adjust to required speed to maintain projector at proper operating range as function of outside ambient temperature Standby All fans are off when projector is in standby and not running active loop-through on a Twin HDMI option card Temperature range for variable fan speed 5 to 40 degrees C Transition steps Smooth speed transitions with no abrupt audible changes Motorized yellow notch filter User selectable optical color switch (in or out) to enhance color space Configurable per channel LiteLOC ™ Automatically adjusts lamp output to maintain constant lumens setting within operating range of lamp. Open Light transmitted to projection lens Closed All light blocked - no light on screen Activation Operation in less than 0.25 seconds. Dual Mercury lamp system Lamps are accessed from side of projector Lamps are individually swappable while the projector is running
Section 6: Specifications M-Series User Manual6-8020-100009-01 Rev.1 (07/08) 6.2.12Status LED 6.2.13Electronics/SW Status LED’s Located at back of projector LED STATES Lamp 1, Lamp 2Off – Lamps are off Yellow – Lamp time has expired and lamp should be replaced Green – Lamp is on and operating correctly Flashing red – Lamp has malfunctioned PowerOff – AC power is off Yellow – AC is present but projector is in standby Green – Projector is powered up and operating normally Flashing green/yellow – Projector communication in progress Flashing red – Error has occurred. Details are displayed on the status display ShutterGreen – shutter is open Yellow – shutter is closed FEATURE COMMENTS Imaging Device Supports 3 chip DMD operation Video Format Re-Sizing All video formats can be resized to fill screen either horizontally or vertically while maintaining aspect ratio Picture in Picture Seamless Switching Built-in 2D keystone and geometry correction Auto-scaling Auto-deinterlacing Edge blending Warping Tiling (support for up to 3x3 arrays) Blanking and Image positioning Brightness, contrast, color, and uniformity user settable control Image orientation Can display image front/rear, normal/inverted (ceiling) Electronics HW access All accessible electronics are mounted from the back of the projector Number of option cards 6 user inter-changeable – hot swappable Number of processor cards2 user inter-changeable Number of option slots 4, located at back of projector for option cards; 1, located at back of projector for processor card Native format adjustment Optional global aspect ratio setting can be set for projector allowing for automatic scaling of all input images to required output format Arbitrary Gamma User definable gamma curves
M-Series User Manual6-9020-100009-01 Rev.1 (07/08) 6.3 IMAGE PROCESSOR PERFORMANCE 6.4 INPUT (SOURCE SIGNAL) COMPATIBILITY 6.4.1Analog (Only) Input 6.4.2Twin HDMI Input Min input pixel rate 13 Mpix/s Max input pixel rate 165 Mpix/s Standard mode Single image processor (SIPC) Max input resolution 2048x1536 (QXGA) Min input resolution 640x400 Max input frame rate with Single Image Processor Card50Hz at 2048x1536 (QXGA) * * With sources that can output minimum blanking, otherwise lower vertical rates Processing 10 bit throughout * * Except Dual-DVI input in dual-link mode (dual 8 bit input paths into 10 bit processing) Source switching time Seamless switching with switch time less than 1 second Connectors 5 female BNC, 75 Ohm R/Pr G/Y B/Pb H/C V Color spaces/signal types RGB YPbPr A/D conversion 10 bits Sampling clock range 13 MHz – 165MHz (SIPC) / 300 MHz (DIPC) Connectors 2 independent HDMI inputs type A 2 loop-out connectors type A Color spaces/signal types RGB YCbCr (4:2:2) YCbCr (4:4:4) HDCP support HDMI 1.3 supported (not including audio) except: 12 bit color dithered to 10 bits; 16 bit color not supported
Section 6: Specifications M-Series User Manual6-10020-100009-01 Rev.1 (07/08) 6.4.3Dual Link DVI Input 6.4.4Video Decoder Input 6.4.5Dual Standard Definition, High Definition or Serial Digital Input 6.5 CONTROL SIGNAL COMPATIBILITY 6.5.1Remote Dual Frequency Connectors 1 dual link DVI-I 1 analog 15-pin VGA Color spaces/signal types HDCP support A/D conversion 10 bits for single link DVI input 8 bits for dual link DVI inputs Frequency 165 MPixel/s analog 300 Mpix/s Dual link DVI (requires DIPC) Connectors 2 S-Video 4-pin miniature DIN 4 BNC, 75 Ohm 2 independent decoder channels for PIP Color space/Signal types Composite video Component video (SD and ED only) S-video Video Standards NTSC, NTSC 4.43, PAL, PAL M, PAL N, PAL 60, SECAM A/D conversion 10 bits Connectors BNC, 75 Ohm Color spaces/signal types Dual HD input SDI, HDSDI Number of transmitters 2 IR Modulation frequency Dual frequency (38 kHz, 455 kHz) Wavelength (peak intensity) 950 nm Range Min 35 m Wired Keypad Wire connection (option) 3 pin XLR Max cable length 30 m XLR Connections Optional boot for remote with XLR connector built- in to avoid requirement to use phono-to-XLR adaptor cable
M-Series User Manual6-11020-100009-01 Rev.1 (07/08) 6.5.2Control Receiver 6.5.3RS232 6.5.4RS422 6.5.5Ethernet 6.5.6USB 2.0 Device Port 6.5.7GPIO 6.5.8DMX512 Interface 6.5.9Built-In Keypad and Display Number of sensors 1 front, 1 rear Coverage 130 degrees coverage in-line with lens at 3 m distance Modulation (carrier) frequency Dual frequency (38 kHz, 455 kHz) Number of ports 2 Connector 1 female 9-pin Dsub (IN) 1 male 9-pin Dsub (OUT) Max bit rate 115.2 kbps Flow control Xon/Xoff Number of ports 1 Connector 1 female 9-pin Dsub Max bit rate 115.2 kbps Power output 12 V ±5% @ 400mA maximum Number of ports 1 Standard 10/100 Base-T Connector Female RJ-45 Number of ports 1 Standard Supports: mass storage device type, Ethernet device type, and/or serial device type. Connector USB type B (full size) Max bit rate 3-12 Mbps (high speed 480 Mbps not supported) Number of I/O Lines 7 Connector Male 9-pin Dsub Output sink current (logic low) 100 mA @ 1V typical Power output 12 V ±5% @ 400mA maximum Connectors 2 5-pin XLR 1 plug and 1 receptacle Input/Output Can be switched in or out via user setting Key type Soft-touch keys Display type Graphics LCD backlight
Section 6: Specifications M-Series User Manual6-12020-100009-01 Rev.1 (07/08) 6.5.10 AMX/Crestron Support 6.6 POWER REQUIREMENTS AMX Device Discovery Partner Crestron Integrated Partner Rated voltage 100 VAC – 240 VAC Rated Current (dual lamp operation) 370W 1080p 12 A @ 100 VAC 200 W 1080p 9 A @ 100 VAC 370W SXGA+ 12 A @ 100 VAC 200W SXGA+ 9 A @ 100 VAC Line frequency 50/60 Hz AC Input Coupler 15 A, 250 VAC Type of connector IEC 320-C14 with wire cable clamp Line Cord 14AWG type FT1 with plug, NEMA 5-15P, 15A Inrush Current 60 A max Maximum Power Consumption 370 W 1080p 1320 W (dual lamp) / 831 W (single lamp) 350 W 1080p 1267 W (dual lamp) / 805 W (single lamp) 300 W 1080p 1135 W (dual lamp) / 739 W (single lamp) 200 W 1080p 871 W (dual lamp) / 607 W (single lamp) 150 W 1080p 739 W (dual lamp) / 541 W (single lamp) 370 W SXGA+ 1320 W (dual lamp) / 831 W (single lamp) 350 W SXGA+ 1267 W (dual lamp) / 805 W (single lamp) 300 W SXGA+ 1135 W (dual lamp) / 739 W (single lamp) 200 W SXGA+ 871 W (dual lamp) / 607 W (single lamp) 150 W SXGA+ 739 W (dual lamp) / 541 W (single lamp) Maximum Current at 100V 370 W 1080p 13.2 A (dual lamp) / 8.3 A (single lamp) 350 W 1080p 12.7 A (dual lamp) / 8.0 A (single lamp) 300 W 1080p 11.4 A (dual lamp) / 7.4 A (single lamp) 200 W 1080p 8.7 A (dual lamp) / 6.1 A (single lamp) 150 W 1080p 7.4 A (dual lamp) / 5.4 A (single lamp) 370 W SXGA+ 13.2 A (dual lamp) / 8.3 A (single lamp) 350 W SXGA+ 12.7 A (dual lamp) / 8.0 A (single lamp) 300 W SXGA+ 11.4 A (dual lamp) / 7.4 A (single lamp) 200 W SXGA+ 8.7 A (dual lamp) / 6.1 A (single lamp) 150 W SXGA+ 7.4 A (dual lamp) / 5.4 A (single lamp)
M-Series User Manual6-13020-100009-01 Rev.1 (07/08) 6.6.1Lamp Specification 6.7 PHYSICAL SPECIFICATIONS 6.7.1Size 6.7.2Adjustment 6.7.3Weight 6.7.4Operating Position 6.7.5Cosmetics PAINT AND COLORS Type Mercury Lamp (Hg) Power 350 W HD/350 W SX+ 300 W min, 370 W max (software adjustable) 200 W HD/200 W SX+ 150 W min, 200 W max (software adjustable) 350W Lamp rated lamp life to 50% brightness (2 hrs on, 15 min off duty cycle)1300 hrs typical @ 370W 1500 hrs typical @ 350W 2000 hrs typical @ 300W 200W Lamp rated lamp life to 50% brightness (2 hrs on, 15 min off duty cycle)2000 hrs typical @ 200W 3000 hrs typical @ 150W Warn-up time (to full output) 5 minutes max Operating position ±20 deg max tilt of lamp axis from horizontal Maximum product dimensions (L x W x H) (with lens removed)561mm (22.1”) x 500mm (19.7”) x 247mm (9.75”) Maximum shipping dimensions (L x W x H) 680mm (26.5”) x 650mm (25.6”) x 458mm (18”) Product Alignment 2” of vertical adjustment on 2 front feet 1” of vertical adjustment on single rear foot Maximum product weight (with lens removed) 25kg (55lb.) Maximum shipping weight (includes packaging) 34kg (75lb.) Horizontal ±20 degrees allowable rotation about lens axis Inverted ±20 degrees allowable rotation about lens axis Rotation ±180 degrees perpendicular to lens axis Skins Sandtek black F63TXB11783-8703 Sherwin- Williams, Polane-T polyurethane enamel. Pale grey text silkscreen Pantone 421 matte finish. Option Cards Faceplates Smooth black 63B12 10 to 15 degree gloss per 010- 100594. Pale grey text silkscreen Pantone 421 matte finish. Card cage Faceplate Grand Century B711-T1856 gloss black. Pale grey text silkscreen Pantone 421 matte finish.
Section 6: Specifications M-Series User Manual6-14020-100009-01 Rev.1 (07/08) 6.8 RELIABILITY AND SERVICEABILITY 6.8.1Reliability 6.8.2Serviceability 6.9 ENVIRONMENT 6.9.1Temperature/Humidity/Altitude 6.10 ACCESSORIES AND SERVICE COMPONENTS MTBF – excluding consumable components 15,000 hrs Consumable components Air filters, fans, lamps Time to replace any option card 1 minute Time to replace lamp 1 minute Time to replace projection lens 30 seconds Time to replace air filter 1 minute Operating temperature range 5 to 40 degrees C Storage temperature range -40 to 70 degrees C Humidity range 10% to 80%, non condensing Operating Altitude 10,000 ft maximum Product NamePart NumberSold With ProductSold Separately Standard Image Processor 108-315101-XX X X Analog Card Input 108-309101-XX X X Dual Link DVI Input 108-312101-XX X X Video Decoder Input 108-310101-XX X X Dual HDSDI Input 108-313101-XX X X Twin HDMI Input 108-311101-XX X X DMX512 Interface 108-314101-XX X X Dust filter 118-100104-XX X Fog filter 118-100105-XX X Stacking frame 118-100107-XX X Ceiling mount 118-100108-XX X Lens ILS 0.73:1SX+/0.67:1HD 118-100110-XX X Lens ILS 1.25-1.5SX+/1.16-1.39HD 118-100111-XX X Lens ILS 1.5-2.0SX+/1.4-1.8HD 118-100112-XX X Lens ILS 2.0-2.8SX+/1.8-2.6HD 118-100113-XX X Lens ILS 2.8-4.5SX+/2.6-4.1HD 118-100114-XX X Lens ILS 4.5-7.3SX+/4.1-6.9HD 118-100115-XX X Lens ILS 7.5-11.2SX+/6.9-10.4HD 118-100116-XX X Lens ILS 1.2SX+/1.1HD 118-100117-XX X Lens ILS 1.2SX+/1.1HD SFL 118-101103-XX Portrait Mode Coupler 118-116109-XX X IR remote 002-120414-XX X X IR remote harness 001-100704-XX X X User Manual 020-100009-XX X Service Manual 020-100010-XX X