Christie Projector J Series 2.0, 2.4, And 3.0kW User Manual

							J Series 2.0, 2.4, and 3.0kW User ManualA-1020-100707-01  Rev. 1  (10-2011)
Appendix A: Menu Tree
A.1 J Series Menu Tree 
						

							A-2J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01  Rev. 1   (10-2011)
Appendix A: Menu Tree 
						

							Appendix A: Menu Tree
J Series 2.0, 2.4, and 3.0kW User ManualA-3
020-100707-01 Rev.1 (10-2011)
Main Menu
1. Size & Position
2. Image Settings
3, Channel Setup
4. Configuration
5. Lamp
6. Status
7. Input Switching & PIP
8. Language
9. Test Pattern
Size & Position
1. Resize Presets
2. Size
3. Vertical Stretch
4. Pixel Track
5. Pixel Phase
6. H-Position
7. V-Position
8. Keep Aspect on Auto Setup
9. Blanking
Blanking
Active Input Window
1. Top Blank
2. Bottom Blank
3. Left Blank
4. Right Blank
Channel Setup
This is a list of all of the
channels that have been
defined for this projector.
Channel Edit:
Card Type
H-Frequency
V-Frequency
Interlaced
Sync Source
1. Name
2. Channel
3. Slot
4. Input
5. In Menu
6. Auto Select
7. Locked
8. Previous Channel
9. Next Channel
Select Channel Operation
Edit Channel
Copy Channel
Delete Channel
Delete Unlocked Only
Delete All Channels
Press 
on a channel
Advanced Main
See Page A4 for Configuration
Image Settings
1. Contrast
2. Brightness
3.Reserved
4. Color Space
5. Video Options
6. Input Levels
7. Advanced Image Settings
Video Options
1. Enable Decoder AGC
2. Video Standard
3. Input Video Black
4. Color
5. Tint
6. Filter
7. Sampling Mode
8. Film Mode Detect
9. Chroma/Luma Delay
10. Adaptive Contrast
11. Split Screen
12. RGB Quantization RangeInput Levels
1. Auto Input Level
2. Red Blacklevel
3. Red Input Drive
4. Green Blacklevel
5. Green Input Drive
6. Blue Blacklevel
7. Blue Input Drive
8. Auto Color Enable
9. Clamp Location
10. Input Peak Detector
11. Color EnableAdvanced Image Settings
1. Gamma Settings
2. Detail Settings
3. Noise Reduction Settings
4. Color Settings
5.Reserved
6. Reserved
Gamma Settings
1. Gamma Correction
2. Gamma
3. Gamma Function
4. Gamma SlopeDetail Settings
1. Detail
2. Texture Enhancement
3. Detail Threshold
4. Detail Overshoot
5. Split ScreenNoise Reduction Settings
1. Noise Reduction
2. Block Artifact Reduction
3. Mosquito Noise Reduction
4. Split Screen
5. Full Screen Eye-Motion Filter
6. Eye-Motion Filter
Color Settings
1. Select Color Adjustment
2. Color Temperature
Lamp
1. Lamp Mode
2. Power
3. Intensity
4. Optical Aperture
5. Warn when lamp reaches (hours)
6. Lamp s/n
7. Change Lamp
8. Lamp History
Input Old Lamp Serial Number
1. Old Lamp Serial Number
2. Continue
3. Abort
Change Lamp
1. New lamp Serial Number
2. Change Lamp
PIP Blanking
Active Input Window
1. Top Blank
2. Bottom Blank
3. Left Blank
4. Right Blank
PIP Image Settings
1. Contrast
2. Brightness
3. Reserved
4. Color Space
5. PIP Video Options
6. PIP Input Levels
7. PIP Advanced Image Settings
PIP Video Options
1. Enable Decoder AGC
2. Video Standard
3. Input Video Black
4. Color
5. Tint
6. Filter
7. Sampling Mode
8. Film Mode Detect
9. Chroma/Luma Delay
10. Adaptive Contrast
11. Reserved
12. RGB Quantization RangePIP Advanced Image Settings
1. PIP Gamma Settings
2. PIP Detail Settings
3. PIP Noise Reduction Settings
4. PIP Color Settings
5. Reserved
6. Reserved
PIP Gamma Settings
1. Gamma Correction
2. Gamma
3. Gamma Function
4. Gamma Slope
PIP Detail Settings
1. Detail
2. Texture Enhancement
3. Detail Threshold
4. Detail Overshoot
5. ReservedPIP Noise Reduction Settings
1. Noise Reduction
2. Block Artifact Reduction
3. Mosquito Noise Reduction
4. Reserved
5. Full Screen Eye-Motion Filter
6. Eye-Motion Filter
PIP Color Settings
1. Select Color Adjustment
2. Color Temperature
PIP Input Levels
1. Auto Input Level
2. Red Blacklevel
3. Red Input Drive
4. Green Blacklevel
5. Green Input Drive
6. Blue Blacklevel
7. Blue Input Drive
8. Auto Color Enable
9. Clamp Location
10. Peak Detector
11. Color Enable
Input Switching PIP
1. Main Input
2. PIP Input
3. Swap Main & PIP inputs
4. PIP Enable
5. PIP Window Options
6. PIP Size & Position
7. PIP Image Settings
8. Fade Time
9. Frame Locking
10. Auto Input Searching
11. HDMI Output Loop Source
12. Standby Active Loop-Through
PIP Window Options
1. PIP Position Presets
2. PIP Window Size
3. PIP H-Position
4. PIP V-Position
5. PIP Border Width
6. PIP Border Color
PIP Size & Position
1. Resize Presets
2. Size
3. Vertical Stretch
4. Pixel Track
5. Pixel Phase
6. H-Position
7. V-Position
8. Keep Aspect on Auto Setup
9. PIP Blanking 
						

							Appendix A: Menu Tree
A-4J Series 2.0, 2.4, and 3.0kW User Manual
020-100707-01 Rev.1 (10-2011)
Configuration
1. Language
2. Output Options
3. Lens Settings
4. Power Management
5. Date & Time
6. Menu Preferences
7. Communications
8. Geometry & Color
9. Diagnostics & Calibration
10. Service
11. Option Card Settings
12.Reserved
Menu Preferences
1. Large Menu Font
2. Menu Location
3. Horizontal Shift
4. Vertical Shift
5. Display Automatic Message Boxes
6. Display User Message Boxes
7. Reserved
8. Display Error Messages
9. Logo Screen Preferences
10. OSD Transparency
11. Menu Type
12. Splash Screen
13. Cascading Menus
Date & Time
1. Date
2. Time
Output Options
1. Screen Image Orientation
2. Reserved
3. Reserved
4. Frame Locking
5. Set Frame Delay
6. Actual Frame Delay
7. Free Run Frequency
8. Fade to Black Time
9. HDMI Output Loop SourcePower Management
1. LCD Backlight
2. LCD Backlight Timer
3. LCD Backlight Level
4. Auto Power Up
5. Auto Shutdown Enable
6. Turn Off Image After (min)
7. Enter Standby After (min)
8.Reserved
9. Over-Temp Fan AssistLens Settings
1. Intelligent Lens System
2. Manual Zoom/Focus
3. Calibrate
4. Lock all Lens Motors
5. Calibrate on New Lens
6. Calibrate on Startup
7. Home Position
Calibration StatusCommunications
1. Serial (RS-232 IN) Options
2. Serial (RS-232 OUT) Options
3. Serial (RS-422) Options
4. Projector Address
5. Network Routing
6. Ethernet Settings
7. Broadcast Keys
8. Front IR Enabled
9. Rear IR Enabled
10. Wired Keypad Enabled
11. DMX / ArtNet Settings
12. SNMP
Ethernet Settings
1. IP Configuration
2. IP Address
3. Subnet Mask
4. Gateway
5. TCP Port
6. Host name
7. Domain name
MAC AddressSerial (RS-232 IN) Options
1. Baud Rate (RS-232 IN)
2. Serial Flow Control (RS-232 IN)
3. Serial Mode (RS-232 IN)
4. Serial Protocol (RS-232 IN)Serial (RS-232 OUT) Options
1. Baud Rate (RS-232 OUT)
2. Serial Flow Control (RS-232 OUT)
3. Serial Mode (RS-232 OUT)
4. Serial Protocol (RS-232 OUT)Serial (RS-422) Options
1. Baud Rate (RS-422)
2. Serial Flow Control (RS-422)
3. Serial Mode (RS-422)
4. Serial Protocol (RS-422)
Advanced Menu continued
Option Card Settings
1. Video Decoder Input card
2. Dual HD/SDI Input Card
3. Twin HDMI Input Card
4. Analog BNC Input Card
Video Decoder Input card
1. Grouped-Inputs Mode
2. Connector 1 Grounding
3. Connector 2 Grounding
4. Connector 3 Grounding
5. Connector 4 Grounding
6. Connector 5 Grounding
7. Connector 6 GroundingDual HD/SDI Input card
1. Dual Link ModeTwin HDMI Input card
1. EDID Timings For Input 1
2. Tx Mode for Output 1
3. EDID Timings For Input 2
4. Tx Mode for Output 2
Menu will be filled with types
that match cards plugged in
Analog BNC Input card
1. Connector Grounding
2. Red Odd Pixel Offset
3. Green Odd Pixel Offset
4. Blue Odd Pixel Offset
5. Red Odd Pixel Gain
6. Green Odd Pixel Gain
7. Blue Odd Pixel Gain
8. Odd Pixel Phase Offset
9. Pixel Phase
10. Input Level Detector
11. Level Detector Threshold
12. Auto Color Enable
13. Color Enable
See Page A5 for:
8. Geometry & Color
9. Diagnostics & Calibration
10. Service
Dual Link DVI Input card
1. EDID Timings for Input 1
2. EDID Timings for Input 2DMX / ArtNet Settings
1. DMX Interface
2. DMX Personality
3. Base Channel
4. Software Termination
5. Artnet Universe
6. Artnet Subnet
7. Input Noise Filter
8. Host name
Main Menu
1. Size & Position
2. Image Settings
3, Channel Setup
4. Configuration
5. Lamp
6. Status
7. Input Switching & PIP
8. Language
9. Test Pattern
PressF
UNC
followed by two numeric numbers to enable
a specific color or colors in the display:
Func60=white
Func61=red
Func 6 2 = green
Func63=blue
Func64=yellow
Func65=cyan
Func66=magenta
Func67=white
Func 6 8 =
Func69=invert(3Donly)
Func09=Ifpressedfrom Status page, opens Service
Status page (For Service personnel only)
Func Help = disables Keystone, Edge Blending and
Brightness Uniformity without changing
the settings associated with them.
Logo Screen Preferences
1. Splash Screen Setup
2. Splash Screen
3. Show Logo Image
4. Horizontal Position
5. Vertical Position
SNMP
1. SNMP Read Community
2. SNMP Location
3. Trap IP Address 1
4. Trap IP Address 2
5. Trap IP Address 3
6. Email Recipient 1
7. Email Recipient 2
8. Email Recipient 3
9. Email From: Address
10. SMTP Server IP Address
11. Trap Configuration
Trap Configuration
1. Lamp Life
2. Lamp Fault
3. Fan Stall
4. Thermal Sensors
5. Power
6. Video signal lost/detected
7. Lamp Door 
						

							Appendix A: Menu Tree
J Series 2.0, 2.4, and 3.0kW User ManualA-5
020-100707-01 Rev.1 (10-2011)
Configuration
1. Language
2. Output Options
3. Lens Settings
4. Power Management
5. Date & Time
6. Menu Preferences
7. Communications
8. Geometry & Color
9. Diagnostics & Calibration
10. Service
11. Option Card Settings
12.Reserved
Advanced Main Menu continued
Color Adjustments by X,Y
1. Select Color Adjustment
2. Color Temperature
Valid Color Space
3. Red X
4. Red Y
5. Green X
6. Green Y
7. Blue X
8. Blue Y
9. White X
10. White Y
11.Reserved
12. Auto Color Enable
13. Color Enable
14. Copy From
Color Saturation
1. Select Color Adjustment
2. Red Part of Red
3. Green Part of Red
4. Blue Part of Red
5. Green Part of Green
6. Red Part of Green
7. Blue Part of Green
8. Blue Part of Blue
9. Red Part of Blue
10. Green Part of Blue
11. Red Part of White
12. Green Part of White
13. Blue Part of White
14.Reserved
15. Auto Color Enable
16. Color Enable
17. Copy From
18. Lamp
Geometry & Color
1. Test Pattern
2. Geometry Correction
3. Brightness Uniformity
4. Edge Blending
5. Color Adjustments by X,Y
6. Color Saturation
7. Black Level Blending
8. Default Color Adjustment
9. Reserved
10. Tiling Setup
SeePageA3
for Lamp
Brightness Uniformity
1. Brightness Uniformity Enable
2. Test Pattern
3. Coarse Adjustment
4. Top Left Corner
5. Left Side
6. Bottom Left Corner
7. Top Right Corner
8. Right Side
9. Bottom Right Corner
10. Center
11. Overall Gain
12. Full Screen Eye-Motion Filter
13. Eye-Motion Filter
14. Reset Brightness Uniformity
Settings
Edge Blending
1. Edge Blending
2. Test Pattern
3. Left Blend Width
4. Right Blend Width
5. Top Blend Width
6. Bottom Blend Width
7. Lamp
8. Show Blending Overlap
9. Advanced Edge Blending
10. Full Screen Eye-Motion Filter
11. Eye-Motion Filter
12. Reset Edge Blending Settings
See Page A3
for Lamp
Black Level Blending
1. Black Blend Enable
2. Test Pattern
3. Left Blend Width
4. Right Blend Width
5. Top Blend Width
6. Bottom Blend Width
7. Center Brightness
8. Left Brightness
9. Right Brightness
10. Top Brightness
11. Bottom Brightness
12. Top Left Brightness
13. Top Right Brightness
14. Bottom Left Brightness
15. Bottom Right Brightness
16. Reset Black Level Blending Settings
Advanced Edge Blending
1. Enable Advanced Curve
2. Left Blend Shape
3. Left Blend Midpoint
4. Right Blend Shape
5. Right Blend Midpoint
6. Top Blend Shape
7. Top Blend Midpoint
8. Bottom Blend Shape
9. Bottom Blend Midpoint
10. Reset Advanced Edge Blending
Settings
SeePageA4for:
1. Language
2. Output Options
3. Lens Settings
4. Power Management
5. Date & Time
6. Menu Preferences
7. Communications
11. Option Card Settings
Geometry Correction
1. Geometry Correction
2. Test Pattern
3. Adjust Horizontal Keystone
4. Adjust Vertical Keystone
5. Adjust 2D Keystone
6. Reset Keystone settings
Tiling Setup
1. Tiling Setup
2. Total Rows
3. Total Columns
4. Row
5. Column
Diagnostics & Calibration
1. Test Pattern
2. Grey Level
3. Freeze Image
4. Color Enable
5. Input Peak Detector
6. Input Level Detector
7. Level Detector Threshold
8. Aspect Ratio Overlay
9. Test Pattern Color Swap
10. Calibrate LiteLoc
Calibration Status
11. Freeze Image During Auto Setup
Service
1.Reserved
2.Reserved
3. Color Primary Settings
4.Reserved
5.Reserved
6. Replace Backplane
7. Remote Access Level
8. Restore Factory Defaults
9. Erase Data Files
10. Delete All Real Time Events
11. Status
Requires the
service
password to
enter this
menu
Color Primary Settings
1. Red X
2. Red Y
3. Green X
4. Green Y
5. Blue X
6. Blue Y
7. White X
8. White Y
9.Reserved
10. Auto Color Enable
11. Color Enable
12. Reset to Factory Color Primaries?
13. Reserved
14. Reserved
Remote Access Level
1. Remote Access Level (Ethernet)
2. Remote Access Level (RS-232 IN)
3. Remote Access Level (RS-232 OUT)
4. Remote Access Level (RS-422)
Main Menu
1. Size & Position
2. Image Settings
3, Channel Setup
4. Configuration
5. Lamp
6. Status
7. Input Switching & PIP
8. Language
9. Test Pattern 
						

							Appendix A: Menu Tree
A-6J Series 2.0, 2.4, and 3.0kW User Manual
020-100707-01 Rev.1 (10-2011) 
						

							J Series 2.0, 2.4, and 3.0kW User ManualB-1020-100707-01  Rev. 1  (10-2011)
Appendix B: GPIO
This section explains how to use a GPIO link from the projector to external equipment, such as devices for
3D synchronizing.
B.1 GPIO Port
The GPIO connector located on the input panel provides a 
flexible method of interfacing a wide range of external I/O 
devices to the projector. There are 7 GPIO pins available on 
the 9pin D-Sub GPIO connector, which are configurable via 
RS-232 commands. The other two pins are reserved for 
ground and power - see table below for pin identification. 
Table B.1 GPIO Pin       
The serial cable required for connecting the external device to the projector GPIO connector, must be 
compatible with the external device.
GPIO PINS
PIN #SIGNAL
Pin 1 + 12V (200mA)
Pin 2 GPIO 2
Pin 3 GPIO 4
Pin 4 GPIO 6
Pin 5 Ground
Pin 6 GPIO 1
Pin 7 GPIO 3
Pin 8 GPIO 5
Pin 9 GPIO 7 
						

							B-2J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01  Rev. 1   (10-2011)
Appendix B: GPIO
Configuring the GPIO
The GPIO connector can be configured to automate any number of events using the serial command code GIO. 
Each Pin is defined as either an input or output depending on the desired outcome. Configure the pin as an 
input if you want the projector to respond to something the device does and as an output if you want the 
external device to respond to an action taken by the projector. For example, configure the pin as an output if 
you want the lighting in a room to automatically dim when the projector is turned on.
By using the GIO command, you can also set the state of each output pin as high or low. By default, the state of 
each pin is high. The voltage applied to pins in the high state is +3.3V.
A low state (or value of 0) will be read on an input pin if the circuit attached to the pin is open. A high state (or 
value of 1) will be read on an input pin if the circuit attached to the pin is shorted to ground. This corresponds 
to a switch closing event.
Example 1. Turn room lighting on when the projector is turned off. (Assumes a control/automation unit is 
configured to turn the lights on when pin 2 of its input goes high.) 
NOTE: The strings in the commands refer to pins 2, 3, 4, 6, 7, 8, 9 in order from left to right. (GIO+CNFG “OOOIIII”) Set pin #2, 3 & 4 configuration to output and 
pin 6, 7, 8 & 9 to input
(GIO+STAT “HLXXXXX”) Set pin #2 to high, pin 3 to low and the state of 
all other pins unchanged
Query Command
(GIO+STAT) Request the state of all pins
(GIO+STAT “HLLHLLH”) Reply of pin states - H means pin is high, L 
means pin is low
(GIO+CNFG) Request the configuration of all pins
(GIO+CNFG “IIIOOOO”) Reply of pin configurations - pins 2, 3 & 4 are 
Inputs, pins 6, 7, 8 & 9 are Outputs 
						

							J Series 2.0, 2.4, and 3.0kW User ManualC-1020-100707-01 Rev. 1 (10-2011)
Appendix C: DMX / ArtNet 
C.1 DMX and Real Time Events
What is DMX?
DMX is a standard for digital communication networks that are commonly used to control stage lighting and 
effects.
What is Real Time Events?
A real time event is a pre-recorded sequence of 1 or more serial commands which are executed when a defined 
trigger occurs. For example: 
• A trigger can be timed based (i.e. Saturday at 1:00pm; occurring every other week)
• A trigger can be event based (i.e. System powers on, good signal, etc.)
• A trigger can be a number of other events (For more details, refer to 4.3.7 Advanced Tabbed Page - RTE)
NOTE: A real time event can use nested loops and delays. Only statically defined commands can be executes 
(i.e. PWR 0, SHU 1). You cannot use variables or other complex programming techniques.
Lens Control Limitiations
WARNING: Normal ILS control of the lens horizontal and vertical positions by the projector respects the 
boundaries of the lens keep out area. This area is necessary to prevent damage to components within the 
projector. When the DMX controls are used to set the absolute position of the lens, setting values in these keep 
out areas may result in an unwanted final lens position. You must ensure that any interim or final lens 
positions, at any time during the lens movement, do not enter the keep out area.
FIGURE C-1 LENS CONTROL LIMITATIONS 
						

							C-2J Series 2.0, 2.4, and 3.0kW User Manual020-100707-01 Rev. 1 (10-2011)
Appendix C: DMX / ArtNet
C.1.1 DMX Channel Setup 
Each personality has a different number of channels:
•Setup Personality - 38 channels
•Show Personality - 18 channels
•ZAP VIP Projector Yoke Personality - 25 channels
It is very important to properly configure the base channel (depending on which personality is used) correctly. 
While the DMX specification allows for device overlapping, this may cause undesired results. Below is a table 
of how projectors should be configured (assuming that all projectors are to be controlled independently and use 
the same personality):
Table C.1 “Show personality” Correct Example Table C.2 “Setup personality” Correct Example
Base Channel All projectors using Show 
Personality (Correct)Base Channel All projectors using Setup
Personality (Correct)
1 Projector 1 (18 ch) 1 Projector 1 (38 ch)
19 Projector 2 (18 ch) 39 Projector 2 (38 ch)
37 Projector 3 (18 ch) 77 Projector 3 (38 ch)
Table C.3 “Show personality” Incorrect Example
Base Channel All projectors using Show 
Personality (Incorrect)
1 Projector 1 (18 ch)
1 Projector 2 (18 ch)
12 Projector 3 (18 ch)