Cine Versum Cineversum Blackwing One User Manual

							2.0  INSTALLATION GUIDELINES
R599763 - Blackwing One User Manual 11 
This unit comes with a optical shift that features vertical and horizontal adjustment of the projection screen position.
Adjust the picture to your screen.
•The Vertical Shift level is between -60% and 60% of the Screen Height (0.60 x H).
•The Horizontal Shift level is between -30% and 30% of the Screen Base (0.30 x B).
•The shift level is set to 0% vertically and horizontally by default, that means that the optical lens is aligned with
the center of the screen.
•If the projector is not installed vertically, use trapezoidal Correction to fulfill your screen.
2.4.0.1 Adjust the picture position vertically
The Blackwing One projector has two dials to center the picture to the screen vertically and horizontally. Refer to the
picture below to locate the dials.
The Vertical and Horizontal shift dials are located at the bottom of the unit.
Turn clockwise to shift the picture on the screen upward.
Vertical Shift Dial
(-60% to +60%)Horizontal Shift Dial
(-30% to +30%) 
						

							2.0  INSTALLATION GUIDELINES
12 R599763 - Blackwing One User Manual
Turn anti-clockwise to shift the picture on the screen upward.
2.4.0.2 Adjust the picture position horizontally
Turn clockwise to shift right the picture on the screen.
Turn anti-clockwise to shift left the picture on the screen.
2.5 Focus and Zoom Adjust
Use the inner ring to adjust the picture focus, and use outer ring to adjust the picture size (zoom).
Focus AdjustZoom Adjust
Zoom In
Zoom Out 
						

							3.0  REMOTE CONTROL UNIT (RCU)
R599763 - Blackwing One User Manual 13 
3.0 REMOTE CONTROL UNIT (RCU)
3.1 General view
3.2 Loading and replacing batteries
•Push the cover tab with the fingernail a little backwards and pull upwards the cover top.
Slide the cover forward to remove.
•Push the battery body towards the spring and lift up to remove.
Insert two AAA size batteries, making sure the polarities match the + and - marks inside the battery
compartment.
•Insert the lower tab of the battery cover in the gap at the bottom of the remote control, and press the cover until
Power ON button
Select Active Input
Select Picture ModeDisplay MenuSTANDBY button
Picture Aspect Ratio Hide DisplayExit to previous menu Navigation buttons
Backlight button Video, PC, HDMI
S-Video, Comp, Switch
Lens ApertureDynamic, Theater, Standard
User1, User2, User3
Digital Zoom
Detail enhancementConfirm button
(Overscan) 
						

							3.0  REMOTE CONTROL UNIT (RCU)
14 R599763 - Blackwing One User Manual
it is firmly closed.
3.3 How to use the remote control unit
The operable distance of the remote control unit is about 7m for direct reception and within 30 degree angle with
respect to the sensor.
CAUTION WHEN USING BATTERIES
Do not mix new and old batteries.Do not mix different type of batteries as they are different in characteristics. Insert
batteries according to the + and - marks on the battery case. Do not put batteries into fire or recharge them if they
are not design to. Remove the batteries if the remote control is not to be used for a prolonged period. Use
manganese batteries wherever possible, Do not use rechargeable batteries.
NOTICE
If the remote control has to be brought closer to the projector to operate, it means that the batteries are wearing out.
When this happens, replace the batteries. Insert the batteries according to the + and - marks. 
The remote control unit can be used by having the transmission signal reflected off a screen, as the effect of
signals reflected from the RCU differ with the type of screen used, operable distance may decrease.
Front InfraRed sensor
Back InfraRed sensor 
						

							4.0  GETTING STARTED
R599763 - Blackwing One User Manual 15 
4.0 GETTING STARTED
4.1 General View
Front side
•Air Inlets: see “Air-Flow and Space Requirements”,  page 8.
•Focus and Zoom Adjust: see “Focus and Zoom Adjust”,  page 12.
Rear side
•Operating LEDs: see section 4.3, page 17 for more details.
•Operating and Navigation buttons described in section 4.4, page 18.
•Lamp trap: see “Replacing the Lamp”,  page 33 for more details on the lamp replacement.
Input Panel side
•Main Power: connect the power cord as shown below.
•Input Panel: connect your video source to the correct input.
Air Inlet
Focus and
Zoom Adjust
IR sensor Air Inlet
Back IR sensor
Operating buttons Air Outlet Operating LEDs
Lamp trap
Main Power
Input Panel 
						

							4.0  GETTING STARTED
16 R599763 - Blackwing One User Manual
4.2 Connecting the Power Cord
•Before plugging in the Power Cord, ensure that all devices have been connected.
•Connect the power cord to the power input terminal of the projector.
CAUTION AGAINST FIRE AND ELECTRIC SHOCK
Since the power consumption of this unit is high, insert the power plug directly into a wall outlet.
When not using devices, remove the power plug from the wall outlet.
Do not use power cords for connection other than specified.
Do not use a power voltage different from that which is indicated.
Do not cut, tear or modify the power cords. Also, do not place a heavy object on, heat or stretch the power cords as
this may cause damage to the cords.
Do not insert or pull plugs with a wet hand. 
						

							4.0  GETTING STARTED
R599763 - Blackwing One User Manual 17 
4.3 Operating LEDs
Operating LED
DescriptionStatus
green LEDPower
red LEDTemp
yellow LEDFan
yellow LED
OffOnOffOffUnit is in standby mode
OnOffOffOffUnit is in operate mode (during projection)
BlinkingOffOffOffUnit is in CooL Down* mode or Starting mode
OffBlinkingOffBlinkingAn error occurred during operation, at least one 
fan is locked.
OffBlinkingBlinkingOffThe projector cannot start because an over 
temperature has been detected.
OffBlinkingBlinkingBlinkingThe lamp failed, replace the lamp.
ABOUT COOL DOWN MODE
After projection or when warning occurred, the heated lamp will go through a 2 minutes cool-down process known
as the Cool Down mode. This function is to prevent damage and deformation from the heated lamp may cause to
the internal components of the projector. It also prevents lamp breakage and shortened lamp life.
The Cool Down mode is indicated by the blinking Status green LED. When in Cool Down mode, the projector cannot
be turned ON.
After the Cool Down process is completed, the unit will automatically switch to the Standby mode.
CAUTION
When in Cool Down mode, do not pull out the plug from the outlet. Also, do not block the air inlets/exhaust vents by
standing the projector on its end or laying it on its side.
STATUS
TEMP
FA N (green LED)
(yellow LED)
(yellow LED)POWER
(red LED) 
						

							5.0  CONNECTIONS
18 R599763 - Blackwing One User Manual
4.4 Operating and Navigation Buttons
5.0 CONNECTIONS
The Blackwing One can be connected to any compatible devices using the available inputs listed below:
•2x HDMI revision 1.3 with HDCP
•1x S-Video
•1x Video
•1x Component
•1x sub D-15 (RGB-VGA)
•2x 12 volt Triggers
•1x RS-232
The RS-232 terminal port can be used for automation.
For audio output, connect your audio video source to an amplifier.
The Blackwing One features 2x12 Volt triggers that can be used to control external device such as the optional 2.35
THEATRE Concept (Ref. T9004000)with Anamorphic Lens.
ButtonDescription
Power buttonTo turn On or Off the projector.
SourceTo navigate into the input selection Menu.
EnterTo select or to confirm.
Up - down - left - rightTo navigate into On Screen Display (OSD) Menu.
ExitTo return to previous menu or cancel action.
MenuTo display On Screen Display (OSD) Menu.
Power button
Up - down - left - right Enter Source
Exit
Menu 
						

							5.0  CONNECTIONS
R599763 - Blackwing One User Manual 19 
5.1 Connecting a device to the projector
For input resolution and refresh rates, check the Specifications table page 38.
InputDevice
YPbPrDVD-Player, HDTV Receiver, Game Console (SD or HD), DVB-T receiver, 
Multimedia box, Analog Camera
VideoDVD-Player, Computer video, Game Console (SD), digital camera, video 
camera.
S-VideoDVD-Player, Game Console, digital camera, video camera
RS-232Automation Device, Control Device or Computer with RS-232*
HDMI1, HDMI2HDMI or DVI-D sources: Blu-Ray Disc player, DVD-player with HDMI, Game 
Console, Computer with DVI-D output.
VGAComputer (VGA output), Multimedia box
Make sure to use a certified HDMI cable, especially when the distance between the different devices are
longer than 5 meters. If it is the case, the use of a split system or optical fiber cable is highly recommended.
*USING RS-232 WITH A COMPUTER
The RS-232 Control and Automation may require specific software and tools. See “Communication Specifications”,
page 35 for more details on RS-232 cabling and protocol.
YPbPr
Video
S-VideoRS-232 (1:1)
HDMI 2
HDMI 1
VGA (Sub D-15) 
						

							6.0  MENU AND PICTURE SETTING
20 R599763 - Blackwing One User Manual
6.0 MENU AND PICTURE SETTING
6.1 Menu Structure
MAIN MENUSUBMENUAVAILABLE OPTIONS
PicturePicture ModeStandard
Dynamic
Theater
User1
User2
User3
Picture AdjustmentBrightness 0-100
Contrast 0-100
Color 0-100
Hue -50 +50
Sharpness 0-100
Color Temperature: Low 
(D65) Medium
Medium High
High
User 1
Red Gain 0-255
Green Gain 0-255
Blue Gain 0-255
Red Bias 0-255
Green Bias 0-255
Blue Bias 0-255
User 2
Red Gain 0-255
Green Gain 0-255
Blue Gain 0-255
Red Bias 0-255
Green Bias 0-255
Blue Bias 0-255
User 3
Red Gain 0-255
Green Gain 0-255
Blue Gain 0-255
Red Bias 0-255
Green Bias 0-255
Blue Bias 0-255