Cine Versum Cineversum Projector Lv Wu6k User Manual

							20
1
2
3
3
Basic operation
Turning off the projector
Press the ON/STAND-BY button on the side control or on
the remote control, and “Power off?” appears on the screen.
Press the ON/STAND-BY button again to turn off the
projector. The POWER indicator starts to flash red, and the
cooling fans keep running. (You can select the level of the
fans’ quietness and running speed.) At this time you can
unplug the AC power cord even if the fans are still running.
When the projector has cooled down enough to be turned on
again, the POWER indicator stops flashing.“Power off” disappears after 4 seconds. 
To maintain the lamp life, once you turn the
projector on, wait at least 5 minutes before turning if off.
Do not operate the proj ector continuously without
reset. Continuous use may result in shortening the lamp life.
Turn off the projector and let it stand for about an hour in
every 24 hours.
Note:
When the On start  function is “On,” this projector is turned on automatically by connecting the AC power cord
to an AC outlet (p. 44).
The running speed of cooling fans is changed according  to the temperature inside the projector.
Do not put the projector in a case be fore the projector is cooled enough.
If the WARNING indicator flashes or emits a red light, see “Warning Indicator”.
While the POWER indicator is flashing, the lamp is being cooled down and the projector cannot be turned on.
Wait until the POWER indicator turns red to turn on the projector again.
The fan rotation will terminate directly if the AC powe r cord is unplugged immediately after the projector is
turned off.
The projector can be turned on after the POWER indicator turns red. The waiting time to restart will be
shortened when the normal power-off processing for fan cooling is completed, comparing with the time the AC
power cord is immediately unplugged after the power-off.
Power off ? 
						

							21
1
2
3
4
5
1
2
3
HDMI
DVI
Computer 1
Video 2
RGBHV
SCART
MENUSELECT
Basic operation
How to operate the on-screen menu
Remote control
The projector can be adjusted or set via the on-screen
menu, including Shortcut menu and Full menu.
General operations are available via the shortcut menu.
A full menu features multiple structures. Each main
menu can be divided into several levels of submenus,
and submenus are also divided into several levels of
sub-submenus. For each adjustment and setting
procedure, refer to the respective sections in this
manual.
Shortcut menu
Press the menu button on the side control or the S.MENU button on the remote control to display the shortcut
menu.
Press the

·ibuttons to select a menu entry. Press the
{
y buttons to adjust settings.
Press the menu button on the side control or the S.MENU button on the remote control again to quit the shortcut
menu. Or press the SELECT button again to show the full menu.
Full menu
Press the menu button on the side control to display
the shortcut menu, and then the SELECT button
again to show the full menu. Or you may directly
press the F.MENU button to show it.
Press the

·ibuttons to select an entry in the
main menu and then the
ybutton to access the
submenu.
Press the

·ibuttons to select your required
entry, and then press SELECT or the
ybutton to
set or enter the submenu.
Press the

·i
{
ybuttons to adjust settings or
switch among the entries. Press the SELECT button
for corresponding operation and then return to the
submenu.
Press the

{button to return to the previous menu.
Press the F.MENU on the remote control again to
quit the full menu mode.
Full menu
Indicators
Select button
button
Full menu button
Input
Input Computer 2
System
Exit Component
S-video
Video 1
Next Move
Next 
						

							22






 


Basic operation
Full menu bar
Main menu Sub menu
(1) PC adjust menu
Used to adjust parameters, like                 
à         
à  
à                                       
Ã
                                                                           
à  
à                                , to match with VGA input signal format.
(2) Screen menu
If a computer is selected as a signal source, the following setup options for the image size are available: Normal, True,
Full, Custom, or Digital zoom +/-.
If video equipment is selected as a signal source, the following setup options for the image size are available: Normal,
Full, Zoom, Wide, Natural wide, Cusrom.
(3) Image select menu
Theavailable image modes are: Dynamic, Normal, Cinema, Blackboard (Green), Colorboard, or User Image.
(4) Image adjust menu
If a computer is selected as a signal source, the following image adjusting options are available: Contrast, Brightness,
Color temp, Red,Green,Blue, Sharpness, and Gamma.
If video equipment is selected as a signal source, the fo llowing image adjusting options are available: Contrast,
Brightness, Color , T i n t , Red,Green,Blue,
Sharpness, Gamma, Noise reduction, andProgressive.
(5) Input menu
Used to select input source, HDMI,DVI,
Computer1,Computer2, Component, Video 1, Video 2, S-Video, RGBHV or SCART.
(6) Sound menu
Used to adjust the volume level or mute the sound.
(7) Setting  menu
Used to configure the projector operation settings.
(8) Network menu
Used to access the network function.
(9) Information menu
Used to display information.
Auto PC adj. Fine sync Total dots Horizontal
ÃVe r t i c a l
ÃClamp
ÃDisplay area H
Display area V Reset Mode free
ÃStore
HDMI
DVI
Computer 1
Video 2
RGBHV
SCART
MENUSELECT
Input
Input Computer 2
System
Exit Component
S-video
Video 1
Next Move
Next 
						

							23
C
C
C
C
Basic operation
Auto setup function
This function is available just by pressing the Auto Setup
button on the top control. The system then automatically
performs various settings in the setup menu, including input
source search, and auto computer adjustment.Arrow keys
Keystone
correcting
button
Auto setup
Remote control

x
z
Lens shift  Control panel (on the right side of the projector body)
1.Use SHIFT on the control panel or LENS of the remote control to adjust the lens.
2. “Lens shift” will jump out on the screen. According to the instruction, please use 

x
z
{
yWRPRYHWKHLPDJHWRWKHGHVLUHGSODFHZÀp° €p0`@€`ÀJLPDJH
     distortion. The maximum shift range is ±50°vertically and ±10°horizontally.
3.Push SHIFT on the control panel or LENS of the remote control and hold on for 
   at least 5 seconds to reset the lens to the center
3 Note:
‡ZKHQWKHOHQVLVLQXQVKLIWHGWKHDUURZVWXUQJU€€

‡ZKHQWKHOHQVLVVKLIWHGWKHDUURZVWXUQ\HOORZ
‡ZKHQWKHOHQVUHDFKHVLWVPD[LPXPVKLIWUDQJHWK€0@PP  `0purn red.
Zoom adjustment
1.Push ZOOM on the control panel or ZOOM of the remote control to 
   enter zoom adjustment.
2. “Zoom” will jump out on the screen. According to instruction, please 
XVH
x
zWR]RRPLQRU]RRPRXW
Focus adjustment 
1.Push FOCUS on the control panel or FOCUS of the remote control
    to enter focus adjustment.
2. “Focus” will jump out on the screen. According to instruction, please 
XVH
x
zWRDGMXVWWKHIRFXV
Focus+ Zoom+
button
buttonShiftLENS
Lens shift 
						

							24
MENUSELECT
16

”

”

”

”

”The arrows are white when there is
no correction.
The direction of the arrows which
are being corrected turns red.
maximum correction.
button on the top control or on the
remote control once more while the
keystone dialog box is being
displayed, the keystone adjustment
is canceled.
The adjustable range can be limited
depending on the input signal.
Keystone
·
iKeystone
If a projected picture has keystone distortion, correct the image
with the Keystone function.
Press the KEYSTONE button on the top control or on the
remote control. The keystone dialog box appears. Correct
keystone distortionwith the arrow buttons

·i. Keystone
adjustment can be stored.
Reduce the upper
width with
the

·button.Reduce the lower
width with theibutton.
Sound adjustment
Direct operation
Vo l u m e
Press the VOLUME+/– buttons on the side control or on
the remote control to adjust the volume.Remote control
Mute
Press the MUTE button on the remote control and select
ON to turn off the sound temporarily. To restore the sound
to its previous level, press the MUTE button again or press
the VOLUME+/– buttons. Mutefunction is also effective
for AUDIO OUT jack.
Vo l u m e  –
button
Sound menu
Full menu operation
1.Press the F.MENU button to display the full screen
menu. Use the

·ibuttons to move the cursor to
the Sound Menu icon. Press SELECT or the

y
button to enter the submenu entry.
2.Use the

·ibuttons to move the cursor to the
desired item, and then press the SELECT button.
Vo l u m e
Press the

·button to increase the volume; press the
i
button to decrease the volume.
Mute
Press the SELECT buttons to switch the mute function. After
the sound is turned off, the mute dialog box display is
changed to “On”. To restore the sound, press the Volume +/- button.
Mute button
Volume+
button
Vo l u m e
MuteSound
Off
Exit MoveNext
Basic operation
Next 
						

							25
Basic operation
HDM I/DVI
Computer
button
Vi d e o b u t t o n
Z D. oom+/-
buttonS-Video
button
Component
button
Arrow buttons

x
z
Lamp mode
button
Freeze
 button
Remote control operation
Using the remote control for some frequently used operations is advisable. Just pressing one of the buttons enables
you to make the desired operation quickly without calling up the on-screen menu.
Remote control
Direct INPUTbutton
Press the Computer/video/HDMI/ DVI/ S-Video/RGBHV/
SCART
/component button to select an input source.
FREEZE button 
Press the FREEZE button to freeze the picture on the screen. To
cancel the Freeze function, press the FREEZE button again or
press any other button.
D.ZOOM button
Press the D.ZOOM button and use the

x
zbuttons to access
the digital zoom mode.
LAMP button
Press the LAMP button to select the lamp mode to change the brightness of
the screen.
No r mal  … Normal  brightness
Auto …… Brightness changes according with the input signal, providing the
contrast of images and thus more real images.
Eco …… Lower brightness reduces the lamp power consumption and extends
the lamp life. ¥Note:
See the next page for the
description of other buttons.
/DVI 
						

							26
02
Ö02
Basic operation
LENS button
ZOOM button
Screen mode
button
Timer button
Focus button
Blank button
button
BLANK button
Press the BLANK button to black out the image. To restore to
normal, press the BLANK button again or press any other
button. The screen changes each time you press the button as
follows.
Black out
:Normal
:Black out
:Normal...
“Blank” disappears after 4 seconds if
there is no other button operation.
TIMER button
Press the TIMER button. The timer display “00:00” appears on the
screen and the timer starts to count time (00:00–59:59).
To stop the Timer, press the TIMER button. Press the TIMER
button again, and then the Timer display disappears.
Timer display
IMAGE button
Press the IMAGE button on the remote control to
select your required image mode.
SCREEN button
Press the SCREEN button on the remote control to
select your required screen mode.
LENS button
Press the LENS button on the remote control to adjust the lens
position.
¥Note:
See the previous page for
the description of other
buttons.
ZOOM button
Press the ZOOM button on the remote control to zoom in/out images.
FOCUS button
Press the FOCUS button on the remote control to adjust the focus of images.
Blank 
						

							27
Computer 1
Computer 2
1
2
HDMI
Computer 1
Computer 2
DVI
RGBHV
SCART
Computer input
Input source selection (Computer 1 or Computer 2)
Direct operation
Press the INPUT button on the side control or the COMPUTER
button on the remote control to select either
Remote control
Input menu
Full menu operation
Press the F.MENU button to display the full
screen menu. Use the
x
zbuttons to select the
inputsourceiconandpressthe
ybutton or
SELECT button.
Press the
x
zbuttons to select Computer 1 or Computer 2
and then press the SELECT button.COMPUTER button
F.MENU button
Component
S-Video
Video1
Video2
RGBHV
Input source selection (RGBHV)
Direct operation
Press the INPUT button on the side control or the RGBHV
button on the remote control to select RGBHV.
Remote control
RGBHV button
F.MENU button
HDMI
Computer 1
Computer 2
DVI
RGBHV
SCART
Component
S-Video
Video1
Video2
HDMI
DVI
Computer 1
Video 2
RGBHV
SCART
MENUSELECT
Input
Input Computer 2
System
Exit Component
S-video
Video 1
Next Move
Next
 Computer 1 or Computer 2 
						

							28
Computer input
Input menuFull menu operation
1.Press the F.MENU button to display the full screen
menu. Use the

·ibuttons to select the input
source icon and press the

ybutton or SELECT
button.
2.Press the
·ibuttons to select RGBHV, and
then press the SELECT button.
HDMI/DVI
Input source selection (DVI)
Direct operation
Press the INPUT button on the side control or the DVI
button on the remote control to select DVI .
Remote control
HDMI/DVI button
F.MENU button
HDMI
Computer 1
Computer 2
DVI
RGBHV
SCART
Component
S-Video
Video1
Video2/DVI
Input menuFull menu operation
1.Press the F.MENU button to display the full screen
menu. Use the

·ibuttons to select the input
source icon and press the

ybutton or SELECT
button.
2.Press the
·ibuttons to select DVI,and
then press the SELECT button.
HDMI
DVI
Computer 1
Video 2
RGBHV
SCART
MENUSELECT
Input
Input Computer 2
System
Exit Component
S-video
Video 1
Next Move
Next
HDMI
DVI
Computer 1
Video 2
RGBHV
SCART
MENUSELECT
Input
Input Computer 2
System
Exit Component
S-video
Video 1
Next Move
Next 
						

							HDMI
DVI
Computer 1
Video 2
RGBHV
SCART
MENUSELECT
Input
Input Computer 2
System
Exit Component
S-video
Video 1
Next Move
Next
29
Auto
-----
Computer input
Computer system selection
The projector automatically tunes to various types of comput ers with its function of Multi-scan system and Auto PC
Adjustment. If a computer is selected as a signal source, theprojector automatically detects the signal format and
tunes to project proper images without any additional setting.
VGA system menu
One of the following messages may appear
when:
The projector cannot recognize the signal
beyond the signal format table, “Auto” is
displayed on the PC System Menu icon and the
Auto PC Adjustment function works to display
proper images. If images are not projected
properly, adjust manually.
There is no signal input from computer. Check
the connection between your computer and
projector.
Selecting computer system manually
The system can also be selected manually.
1. Press the F.MENU button to display the full screen menu. Use the
x
zbuttons to select the input source icon,
and press
ybutton or SELECT button.
2. Use the
x
zbuttons to selec
t System (Signal format), and press
ybutton or SELECT button.
3. Press the
x
zbuttons to select your required system, and then press the SELECT button.The PC system menu displays
the selected system.