Cisco 4507re Manual

  
3-9
Catalyst 4500 E-Series Switches Installation Guide
OL-13972-02
Chapter 3      Installing the Switch
Completing the Installation Process
Figure 3-3 Connecting System Ground on the Switch
St e p 5
Place the grounding lug against the grounding pad making sure there is good metal-to-metal contact 
between the lug and the bare metal of the chassis and that the grounding lug and the attached wire will 
not interfere with other switch hardware or rack equipment.
St e p 6Secure the system ground lug to...

  
3-10
Catalyst 4500 E-Series Switches Installation Guide
OL-13972-02
Chapter 3      Installing the Switch
Completing the Installation Process
Connecting the Supervisor Engine Console Port
This section describes how to connect a terminal or modem to the supervisor engine console port. The 
console port on the supervisor engine allows you to perform the following functions:
•Configure the switch from the CLI.
•Monitor network statistics and errors.
•Configure SNMP agent parameters.
•Download software...

  
3-11
Catalyst 4500 E-Series Switches Installation Guide
OL-13972-02
Chapter 3      Installing the Switch
Completing the Installation Process
Connecting the Supervisor Engine Uplink Ports
This section describes how to connect to the supervisor engine uplink ports. Some supervisor engine 
uplink ports may require the installation of transceivers into the supervisor engine port sockets. Refer to 
the applicable transceiver installation notes for instructions on how to correctly install the transceiver...

  
3-12
Catalyst 4500 E-Series Switches Installation Guide
OL-13972-02
Chapter 3      Installing the Switch
Completing the Installation Process 

CHAPTER
  
4-1
Catalyst 4500 E-Series Switches Installation Guide
OL-13972-02
4
Removal and Replacement Procedures
Revised: March 2013
This chapter provides removal and replacement procedures for the following Catalyst 4500-E series 
field-replaceable units (FRUs):
•Removing and Installing the AC-Input Power Supplies, page 4-2
•Removing and Installing the DC-Input Power Supplies, page 4-8
•Removing and Installing the Chassis Fan Tray Assembly, page 4-14
•Removing and Installing the Backplane Modules,...

  
4-2
Catalyst 4500 E-Series Switches Installation Guide
OL-13972-02
Chapter 4      Removal and Replacement Procedures
Removing and Installing the AC-Input Power Supplies
Wa r n i n gBefore working on equipment that is connected to power lines, remove jewelry (including rings, 
necklaces, and watches). Metal objects will heat up when connected to power and ground and can 
cause serious burns or weld the metal object to the terminals. Statement 43
Wa r n i n gUltimate disposal of this product should be...

  
4-3
Catalyst 4500 E-Series Switches Installation Guide
OL-13972-02
Chapter 4      Removal and Replacement Procedures
Removing and Installing the AC-Input Power Supplies
Figure 4-1 AC-Input Power Supply (Single-Input)
Figure 4-2 Dual-Input AC-Input Power Supply (4200 W and 6000 W) 
1AC in receptacle3Captive installation screws
2Power on/off switch
2313751
2
3
1AC input 2 receptacle4AC input 1 receptacle
2AC input 2 on/off switch5Captive installation screws
3AC input 1 on/off switch
231376100-120V-
12A...

  
4-4
Catalyst 4500 E-Series Switches Installation Guide
OL-13972-02
Chapter 4      Removal and Replacement Procedures
Removing and Installing the AC-Input Power Supplies
Figure 4-3 Triple-Input AC-Input Power Supply (9000 W)
Required Tools
You need a flathead or Phillips-head screwdriver to perform these procedures. 1Power supply status LEDs5AC in connectors (IE60320/C20) (3 inputs)
2Remote power cycling feature terminal block6AC power switches (3 switches)
3Handle7Captive installation screws (2X)...

  
4-5
Catalyst 4500 E-Series Switches Installation Guide
OL-13972-02
Chapter 4      Removal and Replacement Procedures
Removing and Installing the AC-Input Power Supplies
Removing an AC-Input Power Supply
To remove the AC-input power supply, follow these steps:
St e p 1Set the AC-input power supply power switch to the off (0) position (see Figure 4-4).
Figure 4-4 Powering Off the Power Switch (Single-Input Power Supply Shown)
NoteThere are two on/off switches on the 4200 W and the 6000 W AC-input power...

  
4-6
Catalyst 4500 E-Series Switches Installation Guide
OL-13972-02
Chapter 4      Removal and Replacement Procedures
Removing and Installing the AC-Input Power Supplies
Figure 4-6 Loosening the Captive Screws
CautionUse both hands to grasp and support a power supply.
St e p 5Grasp the power supply handle with one hand. Place your other hand underneath to support the bottom 
of the power supply, as shown in Figure 4-7.
Figure 4-7 Handling an AC-Input Power Supply
St e p 6
Slide the power supply out of...