Home > Compaq > Notebook > compaq evo notebook n1010v series User Manual

compaq evo notebook n1010v series User Manual

Here you can view all the pages of manual compaq evo notebook n1010v series User Manual. The Compaq manuals for Notebook are available online for free. You can easily download all the documents as PDF.

Page 41

2-20 Removal and Replacement Service Manual
Removing the Top Case
(Authorized Service Providers Only)
Required Equipment
 • 
#1 Phillips screwdriver.
Removal Procedure
 
1. 
Unplug the AC adapter, if present, and remove the battery.
 
2. 
Remove these additional assemblies:
 • 
Hard disk drive (page 2-6).
 • 
Keyboard cover (page 2-10).
 • 
Speaker assembly (page 2-12).
 • 
Switchboard PCA (page 2-13).
 • 
Keyboard (page 2-13).
 • 
CD/DVD drive (page 2-16).
 • 
Display assembly (page 2-17).
 
3. 
Remove...

Page 42

Service Manual Removal and Replacement 2-21
 
  Figure 2-13. Removing the Top Case
Screw, M2.5×4mm
Screw,
M2.5×6mm (15)
Screw,
M2.5×7mm (2) Screw, M2.5×4mm 

Page 43

2-22 Removal and Replacement Service Manual
Removing the Floppy Drive
(Authorized Service Providers Only)
Required Equipment
 • 
#1 Phillips screwdriver.
Removal Procedure
 
1. 
Unplug the AC adapter, if present, and remove the battery.
 
2. 
Remove these additional assemblies:
 • 
Hard disk drive (page 2-6).
 • 
Keyboard cover (page 2-10).
 • 
Switchboard PCA (page 2-13).
 • 
Keyboard (page 2-13).
 • 
Display assembly (page 2-17).
 • 
Top case (page 2-20).
 
3. 
Remove the screws (right side) that...

Page 44

Service Manual Removal and Replacement 2-23
 
  Figure 2-14. Removing the Floppy Drive
Screw,
M2.5×4mm (2)
Screw,
M2.5×4mm (2) 

Page 45

2-24 Removal and Replacement Service Manual
Reassembly Notes
  Caution
 
Do not excessively bend or fold the floppy drive cable. Excessive flexing can damage the floppy
drive cable connections.
 • 
Connect the floppy drive cable to the motherboard prior to replacing the floppy drive and hard disk
drive guide.
 • 
When replacing the hard disk drive guide, do not secure the left side to the motherboard. The left
side of the guide gets secured during the top case replacement procedure. 

Page 46

Service Manual Removal and Replacement 2-25
Removing the Infrared (I/R) PCA
(Authorized Service Providers Only)
Required Equipment
 • 
#1 Phillips screwdriver.
Removal Procedure
 
1. 
Unplug the AC adapter, if present, and remove the battery.
 
2. 
Remove these additional assemblies:
 • 
Hard disk drive (page 2-6).
 • 
Keyboard cover (page 2-10).
 • 
Switchboard PCA (page 2-13).
 • 
Keyboard (page 2-13).
 • 
Display assembly (page 2-17).
 • 
Top case (page 2-20).
 
3. 
Disconnect the cable from the...

Page 47

2-26 Removal and Replacement Service Manual
Reassembly Note
  Caution
 
Use care when handling the I/R PCA cable. Damaging the cable can degrade notebook
performance.
 • 
Make sure you route the I/R PCA cable between the left screw hole and the bottom case.
 
  Figure 2-15. Removing the I/R PCA
Screw,
M2.5×4mm (2) 

Page 48

Service Manual Removal and Replacement 2-27
Removing the Heatsink (with Fan)
(Authorized Service Providers Only)
Required Equipment
 • 
#0 Phillips screwdriver.
Removal Procedure
 
1. 
Unplug the AC adapter, if present, and remove the battery.
 
2. 
Remove these additional assemblies:
 • 
Hard disk drive (page 2-6).
 • 
Keyboard cover (page 2-10).
 • 
Switchboard PCA (page 2-13).
 • 
Keyboard (page 2-13).
 • 
Display assembly (page 2-17).
 • 
Top case (page 2-20).
 
3. 
Remove all three retaining...

Page 49

2-28 Removal and Replacement Service Manual
 Caution
  Do not spin the fan blades with your finger, or you could damage the fan’s bearings.
Reassembly Notes
 • 
If the thermal pad is damaged, use a sharp knife or scraper to carefully remove it from the heat
sink, then attach a new thermal pad.
 • 
Install the heatsink screws in this order:
1. 
Install all three screws lightly.
2. 
Fully tighten the screws in the order marked on the heatsink. 

Page 50

Service Manual Removal and Replacement 2-29
Removing the CPU Module
(Authorized Service Providers Only)
Required Equipment
 • 
Small flat-blade screwdriver.
Removal Procedure
 
1. 
Unplug the AC adapter, if present, and remove the battery.
 
2. 
Remove these additional assemblies:
 • 
Hard disk drive (page 2-6).
 • 
Keyboard cover (page 2-10).
 • 
Switchboard PCA (page 2-13).
 • 
Keyboard (page 2-13).
 • 
Display assembly (page 2-17).
 • 
Top case (page 2-20).
 • 
Heatsink (page 2-16). 
Start reading compaq evo notebook n1010v series User Manual

Related Manuals for compaq evo notebook n1010v series User Manual

All Compaq manuals