Compaq hp pavilion ze4100 notebook pc User Manual
Here you can view all the pages of manual Compaq hp pavilion ze4100 notebook pc User Manual. The Compaq manuals for Notebook are available online for free. You can easily download all the documents as PDF.
Page 31
2-10 Removal and Replacement Service Manual Removing the Keyboard Cover (User-Replaceable) Required Equipment • #1 Phillips screwdriver. • Small flat-blade screwdriver. Removal Procedure 1. Unplug the AC adapter, if present, and then remove the battery. 2. Remove the two hinge cover screws that secure the keyboard cover to the rear of the notebook. 3. Carefully insert a flat-blade screwdriver blade under the keyboard cover near the right end, then near the center, then near the left end, and...
Page 32
Service Manual Removal and Replacement 2-11 4. If necessary, while holding the center of the cover, carefully insert the flat-blade screwdriver under the right side of the display assembly hinge, gently pry up, and then lift the cover out. This procedure might need to be repeated on the left side of display assembly hinge to completely remove the cover. Figure 2-7. Removing the Keyboard Cover Reassembly Note • Insert the tabs on the left- and right-center of the panel into the mating slots...
Page 33
2-12 Removal and Replacement Service Manual Removing the Speaker Assembly (User-Replaceable) Note: The following speaker assembly removal procedures apply only to Compaq Evo Notebook N1010v and Compaq Presario 1100 Series notebooks. The Pavilion ze4100 Series notebook speakers are integrated into the top case. Refer to the “Removing the Top Case” section later in this chapter for procedures on removing the top case and speakers on the Pavilion ze4100 Series notebook. Required Equipment • #1 Phillips...
Page 34
Service Manual Removal and Replacement 2-13 Removing the Keyboard (User-Replaceable) Required Equipment • #1 Phillips screwdriver. Removal Procedure 1. Unplug the AC adapter, if present, and remove the battery. 2. Remove the keyboard cover (page 2-10). 3. Remove the screws that secure the keyboard to the top case. 4. Lift up on the keyboard at the switchboard PCA end and then pull it toward the display assembly to release the tabs from the top case. 5. Turn the keyboard over and...
Page 35
2-14 Removal and Replacement Service Manual Figure 2-9. Removing the Keyboard Screw, M2.5×4mm (4)
Page 36
Service Manual Removal and Replacement 2-15 Removing the Switchboard PCA (User-Replaceable) Required Equipment • #1 Phillips screwdriver. Removal Procedure 1. Unplug the AC adapter, if present, and then remove the battery. 2. Remove the keyboard cover (page 2-10). 3. Disconnect both the 2-wire and 4-wire cables that connect the switchboard PCA to the top case and speaker assembly, respectively. 4. Remove the screws that secure the keyboard and switchboard PCA to the top case (page 2-13)....
Page 37
2-16 Removal and Replacement Service Manual Removing the CD/DVD Drive (User-Replaceable) Required Equipment • #1 Phillips screwdriver. Removal Procedure 1. Unplug the AC adapter, if present, and remove the battery. 2. Remove these additional assemblies: • Keyboard cover (page 2-10). • Keyboard (page 2-13). 3. Remove the screws that secure the CD/DVD drive to the top case and motherboard. 4. Place your index finger in the top case opening and push out on the CD/DVD drive to release it...
Page 38
Service Manual Removal and Replacement 2-17 Removing the Display Assembly (Authorized Service Providers Only) Required Equipment • #1 Phillips screwdriver. Removal Procedure 1. Unplug the AC adapter, if present, and remove the battery. 2. Remove the keyboard cover (page 2-10). 3. Remove the two retaining screws from the rear of the notebook. 4. Remove the screws from the left and right antenna PCAs. Relocate the antenna PCAs away from the display assembly hinges. 5. Disconnect the...
Page 39
2-18 Removal and Replacement Service Manual Figure 2-12. Removing the Display Assembly Screws, silver M2x4mm (2) Screws, M2.5×6mm (8)
Page 40
Service Manual Removal and Replacement 2-19 Reassembly Notes Important After replacing the display assembly or motherboard, you must use the Service Utilities floppy disk to reprogram the EEPROM on the motherboard for the new display. 1. Download the notebook series service package from the Partnership W eb site (see page vi), and create a Service Utilities floppy disk as described in the package’s Readme file. 2. Plug in an AC adapter. 3. Insert the Service Utilities floppy disk in the floppy...