D-Link Router DHP-1565 User Manual

66
D-Link DHP-1565 User Manual
Section 3 - Configuration
QoS Engine
This  option  is  disabled  by  default.  Enable  this  option 
for  better  performance  and  experience  with  online 
games and other interactive applications, such as VoIP.
This option is enabled by default when the QoS Engine 
option  is  enabled.  This  option  will  allow  your  router 
to  automatically  determine  the  uplink  speed  of  your 
Internet connection.
This displays the detected uplink speed.
The speed at which data...

67
D-Link DHP-1565 User Manual
Section 3 - Configuration
A  QoS  Engine  Rule  identifies  a  specific  message  flow 
and assigns a priority to that flow. For most applications, 
automatic  classification  will  be  adequate,  and  specific 
QoS Engine Rules will not be required.
The QoS Engine supports overlaps between rules, where 
more  than  one  rule  can  match  for  a  specific  message 
flow.  If  more  than  one  rule  is  found  to  match  the  rule 
with the highest priority will be used....

68
D-Link DHP-1565 User Manual
Section 3 - Configuration
Network Filter
Select Turn MAC Filtering OFF,  Turn MAC Filtering ON 
and ALLOW computers listed to access the network , or 
Turn MAC Filtering ON and DENY computers listed to 
access the network from the drop-down menu. 
Enter the MAC address you would like to filter.
To find the MAC address on a computer, please refer to 
the Networking Basics section in this manual. 
Select a DHCP client from the Computer Name drop
down menu and click 

69
D-Link DHP-1565 User Manual
Section 3 - Configuration
Access Control
Check the  Enable Access Control check box and 
click  the  Add  Policy   button  to  start  the  Access 
Control Wizard. 
Add Policy:
The Access Control section allows you to control access in and out of your network. Use this feature as Parental Controls to only grant access to 
approved sites, limit web access based on time or dates, and/or block access from applications like P2P utilities or games.
Click Next to continue with the...

70
D-Link DHP-1565 User Manual
Section 3 - Configuration
Enter a name for the policy and then click Next to continue.
Select  a  schedule  (I.E.  Always)  from  the  drop-down  menu  and 
then click Next to continue.
Enter the following information and then click  Next to continue.
• Address Type - Select IP address, MAC address, or Other Machines.
•  IP Address  - Enter the IP address of the computer you want to apply 
the rule to.
Select the filtering method and then click Next to continue.  

71
D-Link DHP-1565 User Manual
Section 3 - Configuration
Enter the rule:
  Enable - Check to enable the rule.
  Name - Enter a name for your rule.
  Dest IP Start - Enter the starting IP address.
  Dest IP End - Enter the ending IP address.
  Protocol - Select the protocol.
  Dest Port Start - Enter the starting port number.
  Dest Port End - Enter the ending port number.
To enable web logging, click Enable.
Click Save to save the access control rule.
Once your changes have been saved, you can select...

72
D-Link DHP-1565 User Manual
Section 3 - Configuration
Configure Web  Filtering:
Website URL:
Website Filter
Select ALLOW computers access to ONLY these sites, or 
DENY  computers  access  to  ONLY  these  sites   from  the 
drop-down menu. 
Enter the keywords or URLs that you want to allow or block. 
Website Filters are used to allow you to set up a list of Web sites that can be viewed by multiple users through the network. To use this feature select 
the appropriate Web Filtering option, enter the...

73
D-Link DHP-1565 User Manual
Section 3 - Configuration
Inbound Filter
Enter a name for the inbound filter rule.
Select Allow or Deny.
Check to enable rule.
Enter  the  starting  IP  address.  Enter  0.0.0.0  if  you 
do not want to specify an IP range.
Enter the ending IP address. Enter 255.255.255.255 
if you do not want to specify and IP range.
Click the Add button to apply your settings. 
Name:
Action:
Enable:
Remote IP  Start:
Remote IP End:
Add:
The  Inbound  Filter  option  is  an  advanced...

74
D-Link DHP-1565 User Manual
Section 3 - Configuration
Check  the Enable  SPI   box  to  enable  the  SPI  (Stateful 
Packet Inspection, also known as dynamic packet filtering) 
feature.  Enabling  SPI  helps  to  prevent  cyber  attacks  by 
tracking more state per session. It validates that the traffic 
passing through the session conforms to the protocol.
Select one of the following for TCP and UDP ports:
Endpoint  Independent  -  Any  incoming  traffic  sent  to 
an  open  port  will  be  forwarded...

75
D-Link DHP-1565 User Manual
Section 3 - Configuration
1. Check the Enable DMZ box.
2.  Specify  the  IP  address  of  the  computer  on  the 
LAN that you want to have unrestricted Internet 
communication  in  the  DMZ  IP  address  field. To 
specify an existing DHCP client, use the  Computer 
Name drop-down  to select the  computer that 
you  want  to  make  a  DMZ  host.  If  selecting  a 
computer that is a DHCP client, be sure to make 
a  static  reser vation  in  the  Setup  >  Network 
Settings...