D-Link Router DIR-825 User Manual

26D-Link DIR-825 User Manual
Section 3 - Configuration
Wireless Settings
If you want to configure the wireless settings on your 
router using the wizard, click Wireless Security Setup 
Wizard and refer to page 84.
Click Add Wireless Device with WPS if you want to 
add  a  wireless  device  using  Wi-Fi  Protected  Setup 
(WPS) and refer to page 86.
If you want to manually configure the wireless settings 
on your router click Manual Wireless Network Setup 
and refer to the next page. 

27D-Link DIR-825 User Manual
Section 3 - Configuration
Check the box to enable the wireless function. If you do 
not want to use wireless, uncheck the box to disable all 
the wireless functions.
Select  the  time  frame  that  you  would  like  your  wireless 
network enabled. The schedule may be set to Always. Any 
schedule  you  create  will  be  available  in  the  drop-down 
menu. Click Add New to create a new schedule.
Service Set Identifier (SSID) is the name of your wireless 
network. Create a...

28D-Link DIR-825 User Manual
Section 3 - Configuration
Select the Channel Width:
Auto 20/40 - This is the default setting. Select if you are using both 802.11n and\
 non-802.11n wireless devices.
20MHz - Select if you are not using any 802.11n wireless clients.
40MHz - Select if you are using 802.11n wireless clients only.
Select Invisible  if  you  do  not  want  the  SSID  of  your  wireless  network  to  be  broadcasted  by  the  DIR-825.  If  Invisible  is 
selected,  the  SSID of the  DIR-825  will...

29D-Link DIR-825 User Manual
Section 3 - Configuration
802.11n/a (5GHz)
Check the box to enable the wireless function. If you do 
not want to use wireless, uncheck the box to disable all 
the wireless functions.
Select  the  time  frame  that  you  would  like  your  wireless 
network enabled. The schedule may be set to Always. Any 
schedule  you  create  will  be  available  in  the  drop-down 
menu. Click Add New to create a new schedule.
Service Set Identifier (SSID) is the name of your wireless...

30D-Link DIR-825 User Manual
Section 3 - Configuration
Select the Channel Width:
Auto 20/40 - This is the default setting. Select if you are using both 802.11n and\
 non-802.11n wireless devices.
20MHz - Select if you are not using any 802.11n wireless clients.
40MHz - Select if you are using 802.11n wireless clients only.
Select Invisible  if  you  do  not  want  the  SSID  of  your  wireless  network  to  be  broadcasted  by  the  DIR-825.  If  Invisible  is 
selected,  the  SSID of the  DIR-825  will...

31D-Link DIR-825 User Manual
Section 3 - Configuration
This section will allow you to change the local network settings of the router and to configure the DHCP settings.
Network Settings
Enter  the  IP  address  of  the  router.  The  default  IP 
address is 192.168.0.1.
If you change the IP address, once you click Apply, 
you  will  need  to  enter  the  new  IP  address  in  your 
browser to get back into the configuration utility.
Enter  the  Subnet  Mask.  The  default  subnet  mask  is...

32D-Link DIR-825 User Manual
Section 3 - Configuration
DHCP Server Settings
DHCP stands for Dynamic Host Control Protocol. The DIR-825 has a built-in DHCP server. The DHCP Server will automatically assign 
an IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP 
settings to “Obtain an IP Address Automatically.” When you turn your computers on, they will automatically load the proper TCP/IP settings 
provided by the DIR-825. The...

33D-Link DIR-825 User Manual
Section 3 - Configuration
DHCP Reservation
If you want a computer or device to always have the same IP address assigned, you can create a DHCP reservation. 
The router will assign the IP address only to that computer or device. 
Note: This IP address must be within the DHCP IP Address Range.
Check this box to enable the reservation.
Enter the computer name or select from the drop 
down menu and click 

34D-Link DIR-825 User Manual
Section 3 - Configuration
USB Settings
Use  this  section  to  configure  your  USB  port.  There  are 
two  configurations  to  choose  from:  Network  USB  and 
WCN Configuration.
Note: If  using  the  Network  USB  option,  users  will  need 
to  install  the  Network  USB  Utility  into  the  computers  to 
share the USB device through the router.
Choose between these two configuration: Network 
USB and WCN Configuration.
Please  set  the  Network  USB  Detection...

35D-Link DIR-825 User Manual
Section 3 - Configuration
The DIR-825 can be configured as a virtual server so that remote users accessing Web or FTP services via the public 
IP address can be automatically redirected to local servers in the LAN (\
Local Area Network). 
The DIR-825 firewall feature filters out unrecognized packets to protect your LAN network so all computers networked 
with the DIR-825 are invisible to the outside world. If you wish, you can make some of the LAN computers accessible 
from...