Daewoo Dwd M1031 Instruction Manual

							11
Changing the program
If you have accidentally selected the wrong program, follows next procedure. 
Using Time delay
Firstly, you select the desired program and option(s).• Press the Start/Hold button.
The selected program stops and the indicator light of 
Start/Hold button is not twinkle but on. 
• Turn the program selector to OFF and reselect
the desired program by using the program selector.
• If required, select the option(s). 
And press the Start/Hold button. The newly selected  
program starts
• Pressing the “Time delay  ” button, 
select the delayed time.
• Press the “Start/Hold” button. 
The indicator light of “Start/Hold” is off and the
indicator light corresponding to the selected time is on.
•  The displayed time shows program finishing time. 
❋Canceling Time delay
• Press the “Start/Hold” button. 
(Then the indicator light of “Start/Hold” is on.)
• Turn the program selector to OFF.
When the washing is complete, the indicator light of Start/Hold button is not twinkle but on.
• Turn the program selector to OFF .
After washing
 
						

							12
MAINTENANCE
Proper care of your washer can extend its life. This section explains how to care for your washer
properly and safely.
Cleaning your washer
Winter storage or moving care
Install and store your washer where it will not freeze. Because some water may stay in the
hoses, freezing can damage your washer.
If you store or move your washer during freezing weather, winterize it.
Non-use or vacation care
Operate your washer only when you are at home.
If you are on vacation or don’t use your washer for an extended period of time, you should:
• Unplug the power supply cord or turn off eletrical power to the washer.
• Turn off the water supplier to the washer.
This helps avoid accidental flooding (due to a water pressure surge) while you are away.
Wipe up detergent, bleach, and other spills with
a soft, damp cloth or sponge as they occur.
Occasionally wipe the outside of the washer to
keep its looking like new one.Clean interior with 250ml of chlorine bleach
mixed with 500ml of detergent.
Run washer through a complete cycle.
Repeat this process if necessary. Exterior Interior
• Turn off the water tap.
• Disconnect inlet hoses and drain the water
of inlet hoses.
• Run the washer on the drain and spin cycle
setting.
• Unplug the power supply cord.• Flush water pipes and hoses.
• Reconnect water inlet hoses.
• Turn on water faucet.
• Reconnect power supply cord. To winterize washer To use washer again
Do not put sharp or metal object in your washer, or they
can damage the finish. Check all pockets for pins, clips,
money, bolts, nuts, etc.
Do not lay these objects in your washer after emptying
pockets.
 
						

							13
HOW TO CLEAN THE FILTER
Cleaning the water inlet filter
• Clean the filter when water leaks from the water inlet.
Cleaning the drain filter
• This drain filter is used to screen the foreign stuffs such as threads, coins, pins, buttons etc..
• If the drain filter is not cleaned at proper time(every 10 times of use), drain problem could be
caused.
CAUTION: Be careful when draining if the water is hot.
Cleaning the detergent case
• In case of residual detergents or fabric softeners have accumulated ;
- it should be cleaned with a jet of running water.
- If necessary, it can be removed completely from the washing machine. 
• Detergents can be also accumulate the inside cavity. 
In this case, the inside cavity should be cleaned with a brush.
• After cleaning, replace the detergent case and run Rinse cycle without laundry. 
1Turn off the water
tap. 2Separate the inlet
hose.3Pull out the inlet filter.
Clean the inlet filter
with the brush 4Connect the inlet
hose
1. Open the cover-pump(1)  
by using coin. 
Separate the cover-pump(1) 
from the washing machine. 2. Install the cover-pump(1) to the
lower frame(2). 
Open the pump-filter(3) slowly
and allow the remaining water to
flow into a suitable container.3. Remove foreign objects 
from the pump-filter(3) and
clean the interior.
Close the pump-filter(3) and
replace the cover-pump(1).
12
1
3
1
3
1 Pull-out
2 Push and pull again
Push point
 
						

							14
Stained, heavily-soiled, or greasy items may need to be prewashed or soaked for best results.
Soaking helps remove protein-type stains like blood, milk or grass. Prewashing helps loosen soil
before washing.
Stain removal rules
• Use warm water for soaking or prewashing stained laundry. Hot water can set stains.
• Most stains are easier to remove when they are fresh.
• Before treating any stain, find out what kind of stain it is, how old the stain is, what kind of
fabric it is, and whether the fabric is colorfast. (Check the care label)
• Washing and drying can set some stains.
• Start with cold or warm water. Hot water can set some stains.
• When bleach is recommended, use a bleach that is safe for the fabric.
• Put the stained area face down on a paper towel or white cloth. Apply the stain remover to the
back of the stain. This forces the stain off fabric instead of through it.
Stain removal guide
REMOVING STAINS
Rinse immediately in COLD water.
If stain remains, soak in cold water with an enzyme prewash.
Use ice in plastic bag to harden the gum.
Scrape off what you can and the sponge with white spirits.
Sponge with COLD water and soak in an enzyme prewash.
If stains persist, rub in a little detergent and rinse in cold water.
Blot up quickly and rinse out in COLD water.
Rub in a little detergent and wash in the maximum temperature allowed for the
fabric type.
Rinse in COLD water and wash normally.
If stain is still apparent, sponge with white spirits.
Rub affected area with white vinegar and then rinse out in COLD water.
Sponge with white spirits.
Treat stiffened areas with enzyme prewash.
Soak in a COLD enzyme prewash, rinse and wash normally.
Rub affected area with bar soap and wash normally.
Treat as soon as possible by sponging with COLD water.
Rub a little detergent on the stain and wash normally.
Sponge with white spirits.
Rub in an enzyme prewash and wash as normally.
Lay the affected area face down on an absorbent cloth and work from the back.
Sponge with white spirits or dry cleaning fluid. Wash normally.
Apply lemon juice and salt and place in the sun. Wash normally.
Sponge with white methylated spirits and wash normally.
Wash in WARM water and detergent.
Moisten area with lemon juice, dry in the sun and wash normally.
If stain persists and the fabric allows, use a bleach.
Brush off any dry mud. Rinse in cold water.
If stain persists rub in a little detergent and wash normally.
Scrape off any fresh paint and sponge with a non flammable dry cleaning fluid
and wash normally.
Treat while still wet, rinse in WARM water and wash normally.
Dampen a cloth with hydrogen peroxide, lay it over the affected area and press
with a fairly hot iron. Blood
Chewing gum
Cocoa, Chocolate
Coffee
Cream/Milk
Ice cream
Deodorant
Egg
Fabric/Softener
Fruit stains
Grass
Grease and oil
Iron or rust
Lipstick
Mildew
Mud
Paint-oil based
Paint-water based
Scorch marks
STAIN TO REMOVE
 
						

							Most problems are easily solved if you understand the cause.
Check the following list for problem before calling for service.
15
TROUBLE SHOOTING
Program dose not start.
Water dose not enter
the washing machine.
Washing machine is
not drain.
Washing machine is
not spin.
Spin result is
unsatisfactory.
Foam come out of the
detergent case.
Serious noise  and
vibrationPlug is loose or not plugged in.
Power failure.
Loading door is not closed.
Program is not selected.
Start/hold button is  not pressed.
Water tap is not turned on.
Inlet hose is kinked or folded.
Filters is blocked in water inlet
filter.
Drain hose is kinked or clogged.
Pump filter is clogged.
The amount of laundry is too
small. 
The laundry is unbalanced.
Drain hose is placed over 1m
above the floor.
Too much detergent or unsuitable
detergent used.
Transit bolts are not removed.
Washing machine is installed on
uneven floor.
Washing machine is not leveled.Insert plug tightly.
An interrupted program will be resumed when the
power return.
Check whether laundry is trapped in door.
Close the loading door. (a click should be heard)
Select the desired program.
Press the Start/hold button.
Turn the water tap on.
Straighten the inlet hose.
Clean the water inlet filter.
Straighten and clean the drain hose.
Clean the pump filter
Add the laundry to balance. And repeat the Spin
cycle.
Rearrange the laundry. And repeat the Spin cycle.
If articles of heavy clothing (e.g. bath robe) are
loaded, washing machine may skip or stop the spin
cycle. 
Place the drain hose under 1m above the floor.
Repeat the Rinse cycle. 
Remove the transit bolts
Reinstall washing machine on even floor.
Adjust the level of washing machine using adjustable
legs.
Problem Cause Solution
The water tap is closed.
The filter of the valve inlet is clogged.
The valve inlet is an inferior product or broke
down.
The water level sensor (sensor pressure) is an
inferior product or broke down.
The drain motor works during water supply.
The PCB ASS’Y does not check the water level.
The drain hose is kinked or clogged.
The drain motor is an inferior product.
The valve inlet works during drain.
The water level sensor is an inferior product.
The PCB ASS’Y does not check the water level.
The laundry is concentrated to one side of the
drum during spin.
The Start/Hold button is pressed while the door is
opened.
The switch door lock is an inferior product.
The PCB ASS’Y does not check the door lock.CAUSE
IE
OE
UE
LEWATER
INLET 
ERROR
DRAIN 
ERROR
UNBALANCE
ERROR
DOOR
OPEN
ERROR MESSAGE ERROR
Open the water tap.
Clean the filter of the valve inlet.
Change the valve inlet.
Change the water level sensor
(sensor pressure). 
Change the drain motor.
Change the PCB ASS’Y.
Clean and straighten the drain hose.
Change the drain motor.
Change the valve inlet
Change the water level sensor. 
Change the PCB ASS’Y.
Rearrange the laundry.
Close the door.
Change the switch door lock.
Change the PCB ASS’Y.SOLUTION
■ DISPLAY ERROR MESSAGE
 
						

							16
Power Consumption
Dimension (mm)
Maximum mass of textile (kg)
Unit Weight (kg)
Standard Water Consumption
Spin Speed (RPM)
Operating Water Pressure220V~240V/50Hz (2000W)
595x440x850 (WxDxH)
6 kg
54(Net) / 57(Gross)
42
1000/800/600
0.03MPa  ~ 0.8MPa (0.3kgf/cm
2~ 8kgf/cm2) MODEL DWD-M1031
SPECIFICATION
 
						

							# #$
$%
%$
$&
&
!!
( ()
)*
*+
+,
,$
$#
#*
*-
-! !
$ $
(
(.
./0 123 456
789 :;?
ABOUT THIS MANUAL ABOUT THIS MANUAL
@ABCD E
FGHI+*J&& K L M L
N.!O&I*P IQNRSTUS
V.!O&I*P IJIQOSTUS
SW XTTY.TZ.S[Q\] B^ _`
XW
DaUW
>W
[W
bcde ef
f
6D
O*O&!ghi!jkS7lm
nop
#$%$&@A
qrh
,*Pi ZUTQT77T!N+si ZUTQUZYY
TY.T7.T>Qt9-!Xl-![l-!Yl-!ul-!STl-!SSl-!S7lvhav!wx Yl
TY.T7.TuQt9-!Yl-!ul-SSl-!S7lvhav!wx [l
TY.T7.TuQSSl!hav!wx Sl
TY.T7.SuQYl!hav!wx Sl
TY.TZ.XXQYl-!STl-S7lvhav!wx Ul
TY.TZ.XuQSTl-!S[l-S7lvhav!wx Ul
TY.Tu.T>QS7lvhav!wx Sl
TY.Tu.T[Qt9-!S7lvhav!wx Xl
TY.ST.USQYlvhav!wx Sl!jha y:9 \]_`m
TY.SS.X7QYl!hav!wx Sl