Daewoo Fr 291 Service Manual

 11 
9. FAN MOTOR                                             
 FR – 291 
MODEL DAI-6122-DESFD 
TYPE SHADED POLE 
RATING 230V/50HZ 
INPUT 5.0W 
POLE 2 POLE 
RPM  2000 ± 150 rpm 
 
 
 
10. R-THERMOSTAT                                        
 FR – 291 
MODEL GNF-175D-01F(1) 
RATING AC 250V/60Hz 
ON/OFF TEMP. 
2.5 ± 2.5 ℃ 
 
 
 
11. DOOR SWITCH                                          
 FR – 291 
TYPE  1 BUTTON 2 PIN 
RATING AC 250V/0.5A 
MODEL WDS 001C-01 
 
 
12. CONTL BOX HEATER...

 
13
NO PART CODE PA R T  N A M E  Q’TY REAMRK 
1  3010815700  CABINET URT AS  1   
2  3011755200  DOOR S/W AS  1  WDS001C-01 
3  3012924600  HINGE *T AS  1   
4  3016000301  SPECIAL BOLT  3  M5 x L14 
5  3001400000  COVER *T HI  1  PP 
6  3012924500  HINGE *M AS  1   
7  3016004000  SPECIAL BOLT  2  M6 x L10 
8  3012924700  HINGE *U AS  1   
9  7650602511  BOLT HEX  2  M6 x L25 
10  3012105300  FOOT ADJ AS  2  PP+INSERT 
11  3001400200  COVER FAN A  1  HIPS 
12  3013412000  KNOB F CONTL  1  HIPS-c 
13...

 
14 35 3015511000 WINDOW R  1  GPPS 
36 3011187300 CASE ICING  1  PP 
37 3017843700 SHELF F  1  GPPS 
38 3017843600 SHELF R  2  GPPS 
39  3001400700  COVER VEGETB CASE  1  GPPS 
40 3011187600 CASE VEGETB  1  GPPS 
41 3019027900 POCKET F  2  GPPS 
42  3012319500  GASKET F DR AS  1  PVC-S+MAGNET 
43  3011766900  DOOR F URT AS  1   
44 3011187200 CASE EGG  1  PP 
45 3019027800 POCKET EGG  1  GPPS 
46 3019028200 POCKET UTILITY  1  GPPS 
47 3019028000 POCKET JUMBO  1  GPPS 
48 3019028100 POCKET R  1  GPPS...

 
15
9. Methods of exchanging main parts. 
1. F LOUVER    PART 
  
 
 
 
 
- Remove the screw cap, and unscrew the 
 fixing screw(2EA). 
 
 
 
 
 
  
 
 
 
 
-  Pull the louver forward, grasping at the fan 
cover and upper corner of louver. 
 
 
 
 
 
  
 
 
 
 
- Disassemble fan motor harness and remove 
Louver As..   
 
 
 
 
 
 
  
 
 
 
- Unscrew the fixing screw at the back of 
louver(hidden under Al tape). 
 
- To remove the fan cover, pull the bottom of 
 fan cover. 
 
 
 
  
 

 
16 
2.  EVAPORATOR PART 
  
 
 
 
 
- Pull the suction pipe and capi. Tube forward,   
with care not to bend the pipes sharply. 
 
 
 
 
 
  
 
 
 
 
 
-    Hold up evaporator and pull it forward. 
 
 
 
 
 
  
 
 
 
 
- Remove the evaporator pad. 
 
 
 
 
 
 
  
 
 
- To remove defrost heater, cut the clamp cable 
first, disassemble the harness then pull down 
the heater. 
 
- The assembling procedure of new heater is 
  the reverse of disassemble steps. 
 
 
  
 
 

 
17
 
  
 
 
 
 
- To exchange the Bi-Metal, first cut the 
  clamp cable then disassemble the harness. 
 
 
 
 
 
  
 
 
- Extract the Temp. Fuse in the evaporator 
then disassemble the harness . 
 
- The new Temp. Fuse should be located in the 
same position in the evaporator. 
 
 
 
  
3. CONTROL BOX PART 
  
 
 
 
 
- To remove the temperature control dail, 
Pull it down. 
 
 
 
 
  
 
 

 
18
  
 
 
 
 
 
- Unscrew the fixing screw(1EA) . 
 
 
 
 
 
  
 
 
 
 
- Pull down the control box, then 
  disassemble the harness. 
 
 
 
 
 
  
 
 
 
 
- Remove the lamp cover with screwdriver etc. 
pushing the front hooker part of the cover 
then lift up the cover. 
 
 
 
 
 
  
 
 
 
 
- Unscrew the fixing screw of the lamp socket. 
 
 
 
 
 
  
 

 
19
  
 
 
 
- Pull the lamp forward, then disassemble the 
connector. 
 
- The assembling procedure of new lamp is 
    the reverse of disassemble steps. 
 
 
  
 
4.  DOOR SWITCH PART 
  
 
- In removing the door switch, push the door 
  switch left, insert a pointed rods as screw- 
driver in the right gap, and push the rod left 
and pull the door switch forward. 
 
- Be careful not to harm the surface of cabinet 
. (Use name plate etc. under the pointed rod) 
 
 
  
 
 
 
 
- Pull the door switch...