Daewoo Frs 2011i Service Manual

50
DIAGRAM
Front PCB
 

51
INSTALLATION GUIDE
Installation Preparation
Dimensions( including Door Handles)
(Width*Depth*Height) 928mm 816mm 1808mm FRS-20
(Width*Depth*Height) 928mm 896mm 1808mm FRS-24
Sufficient space from refrigerator back to the
wall for free air ventilationAvoid direct sunlight.
Once the installation place is ready follow the installation instructions.If surround temperature of refrigerator is low (below 5), foods can be frozen or the refrigerator can work
in abnormal way.  
Check if the refrigerator can...

52
INSTALLATION GUIDE
Remove front bottom cover first, if it is attached.Removing Freezer Door 
1
Remove the bottom cover first.
Pull out the left collar of the coupling
first, then hold the coupling and pull
out the left water tube.
3
Turn top hinge fastener
counterclockwise 3~4 times. 
Disconnect the harness wires.
4
Lift up the front of hinge to remove. 
( After the hinge is removed the
door can fall down forward. Be
careful !)
5
Be careful not to damage the water
line when removing the door.
2Turn...

53
INSTALLATION GUIDE
How to install Water Line
WATER SUPPLY KIT
1.  The water pressure should be 3kgf/cm2or more to run the
automatic icemaker .
Checkup your tap water pressure ; if a cup of 180cc is full
within 10 seconds, the pressure is OK.
2.  When installing the water tubes, ensure they are not colse to any hot surfaces.
3.  The water filter only   filters water ;  it does not eliminate any
bacteria or microbes.
4. If the water pressure is not so high to run the icemaker ,  call the local plumber...

54
INSTALLATION GUIDE
7. Fasten the Water Tube. 5. Attach the Filter Box
6. Connect the Water Tube to the refrigerator.
1) Remove the rear cover at the bottom back of the refrigerator.
2) Insert the fastening ring into the Water tube. 
(Be careful to follow the direction of the nut.)
3) Insert the Water Tube into the top of Water Valve, turn the nut clockwise to
fasten it. (The Water valve is to the right of the motors.)
4) Check for any bent tubes or water leaks; if so, re-ckeck instalation procedure....

55
INSTALLATION GUIDE
Replacing Freezer Door
2Insert the bottom hole of freezer
door straight to the bottom hinge pin.1Insert the water tube into the hole of
the bottom hinge pin first, then 
Insert the bottom of freezer door into
the bottom hinge pin.
3Let the top of door close to the
cabinet and insert the top hinge
pin to the top hole of freezer door.
( Insert the back of hinge to the
groove of protrusion first, then
front to the top hole of door.)
4Turn the hinge fastener tightly to the
end.
Connect...

56
INSTALLATION GUIDE
Refrigerator Leveling & 
Door Adjustment ( If needed. )
Refrigerator must be level in order to maintain optimal performance and desirable front appearance.
(If the floor beneath the refrigerator is uneven, freezer and refrigerator doors look unbalanced.) 
In case freezer door is lower than refrigerator door ...
The front of refrigerator needs to be higher just a little than the back for easy
door closing, but if the wheel is raised too much for door balance, i.e. front of...

57
EXPLODED VIEW AND PARTS LIST
Total Explded View
FRS-2011
CABINET
MECH ROOM
17
16
15
14
 1 8
 3
1113
 2 4 6
 7
 91012
181920
21
31
23
32
26
2728
25
2224
3334
29
30
56
3736
43
51
45
46
54
383940
47
50
52
4948
44-1
55
53
41
4244-2
 

58
EXPLODED VIEW AND PARTS LIST
FRS-2011
R ROOM
66
70
64
65
71
72
59
60
57
58
61
62
82
83
93
94
9798
92
99
9091
88
89
68
74
67
69
76
73
79
63
77
80
81
86
96
87
7595
8485
 

59
EXPLODED VIEW AND PARTS LIST

FRS-2011
F ROOM119
121
122
120
118
117
110
126
106
105
104
131
132
129
128
130
109
133
74
134
108
127
107
75100
101
114
102
103
112
124123
111
125
113