DELL 1110 User Manual

   
 
 
2. Pull the used toner cartridge out and lift it up and away from the printer.  
 
   
 
 
 
3. Unpack a new toner cartridge. Hold the cartridge carefully and thoroughly shake it from side - to - side 5 or 6 times to distribute the toner.  
 
   
4. Pull the tape to remove the protective paper.    
   
       
 
5. Locate the cartridge slot inside the printer, one on each side.    
   
    CAUTION:  Avoid reaching too far into the printer. The fusing area may be hot.
NOTE:  If toner comes into...

6. Unfold the toner cartridge handle and grasp it. Insert the cartridge into the printer until it snaps into place.    
   
 
7. Close the front cover. Make sure that the cover is securely closed. If it is not firmly closed, printing errors may occur.    
   
Ordering Supplies  
     
You can order supplies using the Dell   Toner Management System or by contacting Dell at  www.dell.com/supplies .  
     
In addition to the toner level indicator that is displayed in the Printing Status window each time...

Paper Handling   
   
Print Media Guidelines  
Printer media includes paper, card stock, transparencies, labels, and envelopes. Your printer provides high quality printing on a variety of print media. Selecting 
the appropriate print media for your printer helps you avoid printing problems. To get the best possible print quality, use only high - quality, copier - grade paper.  
When you choose print materials, consider the followings:  
   
l Desired outcome : The paper you choose should be appropriate...

l Store unused materials at temperatures between 15 ° C and 30 o C (59 ° F to 86 ° F). The relative humidity should be between 10% and 70%.  
 
     
l During storage, you should use moisture - proof wrap, such as a plastic container or bag, to prevent dust and moisture from contaminating your paper.  
 
     
l Load special paper types one sheet at a time.  
 
     
l Only use materials specifically recommended for use with laser printers.  
 
     
l To prevent special materials, such as transparencies...

   
   
Loading Print Media in the Paper Tray  
   
Proper paper loading helps prevent paper jams and ensures trouble - free printing. Do not remove the paper in the tray while a job is printing. Doing so may 
cause a paper jam. See  Types, Input Modes, and Capacities  for acceptable paper size and capacity for the tray. You can load approximately 150 sheets of 
plain paper in the tray.  
   
Open the paper input tray and load the paper in the paper tray with the side to be printed on facing up....

   
 
Adjust the paper length and width guides against the print material without bending it.  
2. To print a document in Manual Feed mode, you must select  Manual Feed  for  Source  from the software application, and then select the appropriate 
paper size and type. For details, see  Paper Tab .  
 
3. Press    on the printers operator panel to start feeding.  
Printing starts.    
 
4. If you are printing multiple pages,  load the next sheet after the first page prints out, and press  .  
Repeat this...

   
 
 
 
l Load a transparency in the tray  with the side to be printed on facing up , and the  top  with the adhesive strip inserted first .  
 
   
 
 
 
 
 
l Load a sheet of card stock  with the side to be printed on facing up , short edge first,  from the center of the tray.  
 
 
   
 
 
l Load a letterhead in the tray  with the design face up ,  top edge toward the printer .  
 
 
   
 
  NOTE:  To prevent labels from sticking to each other, do not let the printed label sheets stack up as they...

Printing   
     
   
Printing a Document  
  The driver provided with your printer allows a wide variety of options. The features provided by the printer driver are as follows:  
   
The following procedure describes the general steps required for printing from various Windows applications. The exact steps for printing a document may vary 
depending on the application program you are using. Refer to your software applications  Users Guide  for the exact printing procedure.   
1. Open the document you...

Press  . In Manual Feed mode, you cant cancel a print job by pressing  .    
 
   
   
Your printer finishes printing the page that is moving through the printer and deletes the rest of the print job. Pressing    cancels only the current job.  If more 
than one print job is in the printers memory,  you need to press    once for each job.  
 
To stop a print job from the Printers folder:  
1. From the Windows  Start  button, click  Settings .  
 
2. Select to  Printers  (Windows 98/Me/2000) or  Printers...