Dell 2208wfp Users Guide

 
Notes, Notices, and Cautions  
   
   
   
 
Information in this document is subject to change without notice.  
 
Reproduction in any manner whatsoever without the written permission of Dell Inc.   is strictly forbidden.  
Trademarks used in this text:  Dell , the  DELL  logo,  Inspiron ,  Dell Precision ,  Dimension ,  OptiPlex ,  Latitude, PowerEdge, PowerVault, PowerApp, and Dell OpenManage  are trademarks of Dell 
Inc;   Microsoft, Windows,  and  Windows NT  are registered trademarks of Microsoft...

Back to Contents Page    
 
About Your Monitor   
 
Product Features  
The  2208WFP  flat panel display has an active matrix, thin - film transistor (TFT), liquid crystal display (LCD). The monitor features include:   
■  22 - inch (573.6 mm) viewable area display.   
■  1680 x 1050  resolution, plus full - screen support for lower resolutions.   
■  Wide viewing angle to allow viewing from a sitting or standing position, or moving side - to - side.   
■  Tilt, swivel, vertical extension and rotate...

Back View  
Side View  Front panel controls
Label Description
1 Input Source select
2  OSD Menu/Select button
3 Brightness & Contrast/ Down ( - ) button 
4 Auto - adjust/ Up (+) button
5 Power button (with power light indicator)
Back view Back View with monitor stand
Label Description
1 VESA mounting holes (100mm)  
(Behind attached base plate)   Use t o mount the monitor.  
   
2  Barcode serial number label Refer to this lable if you need to contact Dell for 
technical support. 
3 Security lock slot...

Bottom View     USB 
connectors 
(downstream)
     
    Right view
   
Label Description
1 AC power cord connector.
2 DC power  connector  for Dell Soundbar.
3 DVI connector
4 VGA connector
5 USB upstream port
6 USB connector port 
Monitor Specifications  
The following sections give you information about the various power management modes and pin assignments for various connectors for your monitor.   
Power Management Modes  
If you have VESA's DPM™ compliance display card or software installed in...

The OSD will only function in the  normal operation  mode. When the  menu  or  plus  buttons are pressed in Active - off mode, one of the following messages will be displayed: 
Analog Input In Power Save Mode. Press Computer Power Button  or Any Key on Keyboard or Move Mouse  
OR   
Digital Input In Power Save Mode. Press Computer Power Button or Any Key on Keyboard or Move Mouse  
Activate the computer and the monitor to gain access to the  OSD.  
* Zero power consumption in OFF mode can only be...

6 DDC Clock
7 DDC Data
8 No connector 
9 T.M.D.S. Data 1 -
10 T.M.D.S. Data 1+
11 T.M.D.S. Data 1 Shield 
12 No connector 
13 No connector 
14 +5V power
15 Self test 
16 Hot Plug Detect
17 T.M.D.S. Data 0 -
18 T.M.D.S. Data 0 Shield
19 T.M.D.S. Data
20 No connector
21 No connector
22 T.M.D.S.Clock Shield
23 T.M.D.S. Clock+
24 T.M.D.S. Clock -
Universal Serial Bus (USB) Interface  
This section gives you information about the USB ports that are available on the left side of your monitor.  
USB Upstream C...

USB P orts    
l 1 upstream  -  rear   
l 4 downstream  -  2 on rear; 2 on left side  
NOTE:  USB 2.0 functionality requires a USB 2.0 - capable computer  
NOTE:  The monitors USB interface works only when the monitor is on or in power save mode. If you turn off the monitor and then turn it on, the attached peripherals may take a few 
seconds to resume normal functionality. 
Plug and Play Capability  
You can install the monitor in any Plug and Play - compatible system. The monitor automatically provides...

VESA, 1152 x 864 67.5 75.0 108.0 +/+
VESA, 1280 x 1024 64.0 60.0 135.0 +/+
VESA, 1280 x 1024 80.0 75.0 135.0 +/+
VESA, 1680 x 1050 65.2 60.0 146.3 - /+
VESA, 1680 x 1050 64.6 60.0 119.0 +/ -
Electrical  Specifications  
Video input signals Analog RGB, 0.7 Volts +/ - 5%, positive polarity at 75 ohm input impedance  
Digital DVI - D TMDS, 600mV for each differential line, positive polarity at 50 
ohm input impedance  
Synchronization input signals Separate horizontal and vertical synchronizations, polarity...

               
Maintenance Guidelines  
Cleaning Your Monitor  
For best practices, follow the instructions in the list below while unpacking, cleaning, or handling your monitor:  
l To clean your antistatic screen, lightly dampen a soft, clean cloth with water. If possible, use a special screen - cleaning tissue or solution suitable for the 
antistatic coating. Do not use benzene, thinner, ammonia, abrasive cleaners, or compressed air.   
l Use a lightly - dampened, warm cloth to clean the monitor....

Back to Contents Page    
 
Appendix   
 
  Safety Instructions  
  FCC Notice (U.S. Only) and Other Regulatory Information   
  Contacting Dell  
CAUTION: Safety Instructions  
For information on safety instructions, see the  Product Information Guide .   
FCC Notices (U.S. Only) and Other Regulatory Information  
For FCC notices and other regulatory information, see the regulatory compliance website located at  www.dell.com
egulatory_compliance .  
Contacting Dell  
For customers in the United States,...