DELL 2350dn User Manual

							7.
From the Printer Settings page, select  Paper Menu.
8.
Select  Paper Type .
9.
Select the paper type you have in each tray.
10.
Click  Submit .
11.
Loading the 250-Sheet Paper Tray
Follow these instructions to load paper in the 250-sheet paper tray.
Remove the tray.
1.If you are loading legal or folio-size paper, you must adjust the paper tray to accommodate the larger
paper.
Press down on the latch at the back of the tray.
a.
Expand the tray until the extender locks into place.
b.
2. 
						

							b.
If you are loading an A6, you must lift the tab to accommodate the paper.
NOTE: Make sure the paper is below the maximum fill line located on the edge of the tab.
Overloading the tray can cause paper jams and possible printer damage.
3.
Flex a stack of paper back and forth. Straighten the edges on a level surface.
4. 
						

							4.
Load the paper in the tray with the print side facing down.
Ensure that the paper is below the maximum fill line on the side paper guides. Overloading may cause
paper jams.
5.
Slide the two side guides and the rear guide until they rest against the edges of the paper.
6.Replace the tray.
7.Extend the paper support on the output bin.
8. 
						

							8.
Loading the 550-Sheet Paper Tray
Follow these instructions to load paper in the 550-sheet paper tray.
Remove the tray.
1.If you are loading legal or folio-size paper, you must adjust the paper tray to accommodate the larger
paper.
Press down on the latch at the back of the tray.
a.
Expand the tray until the extender locks into place.
b.
2. 
						

							b.
Flex a stack of paper back and forth. Straighten the edges on a level surface.
3.Load the paper in the tray with the print side facing down.
Ensure that the paper is below the maximum fill line on the side paper guides. Overloading may cause
paper jams.
4.Slide the two side guides and the rear guide until they rest against the edges of the paper.
5. 
						

							5.
Replace the tray.
6.
Extend the paper support on the output bin.
7.
Using the Rear Exit
The single-sheet rear exit provides a straight-through paper path to help reduce curling and potential jams.
This is especially useful for specialty media, such as transparencies, envelopes, labels, card stock, or index
cards.
To use the rear exit, open the rear exit door. When the rear exit door is open, all print jobs come out the
rear exit. When closed, all print jobs are sent to the output bin on top of the printer. 
						

							Using the Multipurpose Feeder
Configuring the Multipurpose Feeder
This setting is used to designate the mode of operation for the multipurpose feeder.
Mode  
Cassette* The multipurpose feeder source:functions as a non-sensing automatic source
is assigned an installed size and paper type like any of the other input
sources
is included in the value lists of all printer settings such as the Paper
Source
Manual The multipurpose feeder source:is used strictly for manual feed
is removed from the value lists of all printer settings, including Paper
Source
When manual feed is selected, the printer suspends printing and prompts
the user to load print media manually into the multipurpose feeder.
* Factory default setting
Opening the Multipurpose Feeder
The multipurpose feeder is located at the front of your printer and can feed 50 sheets of print media at a
time. You can use the multipurpose feeder to make quick runs of paper types or sizes that are not currently
loaded in the paper tray.
To open the multipurpose feeder:
Pull the multipurpose feeder door down.
1. 
						

							1.
Slide the multipurpose feeder tray forward.
2.Pull the extension so it flips forward.
3.Guide the extension down gently to fully extend the multipurpose feeder.
4.
Loading the Multipurpose Feeder
To load the multipurpose feeder:
Place a sheet of the selected print media, print side facing up, at the center of the multipurpose feeder,
but only to the point where its leading edge can contact the paper guides. Otherwise, the printer
1. 
						

							engages the print media too soon and likely skews the print job.
NOTE: Do not exceed the maximum stack height by forcing paper or specialty media under the
stack height limiters which are located on the guides.
1.
Adjust the paper guides to the print medias width.
2.Prepare the print media for loading. Flex sheets of paper or paper labels back and forth to loosen them. Do not fold or crease the
paper or labels. Straighten the edges on a level surface.
NOTE: Avoid touching the print side of the transparencies. Be careful not to scratch them.
3. 
						

							Flex a stack of envelopes back and forth to loosen them. Straighten the edges on a level surface.
NOTE: Do not fold or crease envelopes.
Hold both sides of the print media close to the multipurpose feeder, and load it into the printer.4.
NOTICE: Do not force the print media into the feeder. Forcing the media causes jams.
Insert envelopes with the flap side facing down and with the stamp area as shown.
NOTE: For best performance do not use envelopes that have postage stamps attached.
Hold transparencies by the edges, and avoid touching the print side. Oil from your fingers that is
deposited on the transparency can affect print quality.