Dell E2009w Users Guide

Push  to  go back  to  the main menu.
 and   buttons to  adjust  image left  and  right. Minimum  is 0  (-). Maximum is 100  (+).
NOTE:  When  using
 and   buttons to  adjust  image up  and  down. Minimum  is 0  (-). Maximum is 100  (+).
NOTE:  When  using
 or  to  adjust  the sharpness from  0  to  100.
 and   buttons to  adjust   for best image quality.
OTHER
SETTINGS
 to  go back  to  the main menu.
 and   buttons to  adjust  the slider in 1 second  increments,  from  5 to  60  seconds.
 button....

NOTE: For  best user  experience and  optimum performance  of your  monitor,  keep this feature  enabled.
NOTE:  Press  any button on the monitor to  terminate LCD  Conditioning  at any time.
 

Activate the computer  and  wake  up  the monitor to  gain access  to  the OSD
or
OSD Warning Messages
One  of the following warning  messages may appear on the screen indicating  that  the monitor is out of synchronization.
or
This means that  the monitor cannot synchronize with the signal  that  it  is receiving from  the computer. See 
Monitor Specifications for the Horizontal  and  Vertical
When  monitor enters Power Save mode, the following message  appears :
Solving  Problems for more...

If  you do not see 1680 x  1050 as an option,  you may need  to  update your  graphics driver. Depending on your  computer, complete  one  of the following procedures:
If  you have  a  Dell desktop or portable computer:Go to  support.dell.com ,  enter your  service  tag, and  download the latest  driver  for your  graphics card.If  you are using  a  non-Dell computer  (portable  or desktop):Go to  the support site for your  computer  and  download the latest  graphic drivers.Go to  your  graphics card...

You  can  tilt  the monitor to  best fit  your  viewing needs.
Back to  Contents Page
 

Back to  Contents Page
Troubleshooting
Dell™ E2009W/E2209W Flat Panel Monitor  Users Guide
Troubleshooting Your  Monitor
Common Problems
Product Specific  Problems
CAUTION: Before  you begin any of the procedures in this section, follow  the Safety Instructions
Troubleshooting Your Monitor
Self-Test Feature Check
Your  monitor provides  a  self-test feature  that  allows  you to  check  whether  your  monitor is functioning properly. If  your  monitor and  computer  are properly
connected but the monitor...

Verify  that  the power outlet is functioning properly  by using  any other electrical equipment.Ensure  that  the power button is depressed fully.
No  Video/ Power LED on No  picture
or no
brightness
Increase brightness & contrast  controls via OSD.Perform monitor self-test feature  check.Check for bent or broken pins in the video  cable  connector.Run the built -in diagnostics.
Poor Focus Picture  is
fuzzy,
blurry,  or
ghosting
Perform Auto Adjust  via OSD.Adjust  the Phase and  Pixel  Clock  controls...

Specific  SymptomsWhat You Experience Possible Solutions
Screen image is too  small Image is centered on screen, but does  not fill
entire  viewing areaCheck the Scaling  Ratio setting  in Image Setting  OSD.Reset  the monitor to  Factory Settings .
Cannot adjust  the monitor
with the buttons on the front
panel OSD does  not appear on the screen
Turn off the monitor,  unplug  the power cord, plug back, and  then  turn
on the monitor
.
The  picture does  not fill  the
entire  screen. The  picture cannot...

Back to  Contents Page
Appendix
Dell™ E2009W/E2209W Flat Panel Monitor  Users Guide
Safety Instructions
FCC Notice (U.S.  Only) and  Other  Regulatory  Information
Contacting Dell
CAUTION: Safety Instructions
CAUTION: Use of  controls,  adjustments, or  procedures other  than those  specified  in this  documentation  may result  in exposure  to shock,
electrical hazards, and/or mechanical  hazards.
For  information  on safety instructions,  see the  Product Information  Guide.
FCC Notices (U.S. Only) and...