Dell S300 Projector Users Guide

							Using Your Projector51
Managing Properties
Home
• Access the Web Management Home page by entering the projector’s IP 
address at the web browser. See Network on page 41.
•Language: Allows you to set the language for web management. 
						

							52Using Your Projector
Network Settings
See OSD section on page 41.
•Set up the Model Name, Projector Name, Location and Contact 
information (up to 21 characters for each field). Press Save to store the 
settings.
• Choose DHCP to assign an IP address to the projector from a DHCP server 
automatically, or Manual to assign an IP address manually.
•Set up the IP Address, Device ID and Po r t information on the Crestron 
function. 
						

							Using Your Projector53
Projector Status and Control Page
•Projector Status: There are 5 status: Lamp On, Standby, Power Saving, 
Cooling and Warming up. Click the Refresh button to refresh the status and 
control settings.
•Po w e r  S a v i n g: Power Saving can be set to Off, 30, 60, 90, or 120 minutes. 
Refer to page 45.
•Alert Status: There are 3 error status: Lamp warning, Low lamp life, and 
Temperature warning. Your projector might lock up in protection mode if 
any of the alerts is activated. To exit protection mode, click the Clear button 
to clear the Alert Status before you could Power ON your projector.
•Projector Mode: Allows you to select the projector mode, depending upon 
how the projector is mounted. There are 4 projection modes: Front 
Projection-Desktop, Front Projection-Ceiling Mount, Rear Projection-
Desktop and Rear Projection-Ceiling Mount
•Source Select: The Source Select menu allows you to select your projector 
input source. You can select VGA-A, VGA-B, S-V
IDEO, COMPOSITE VIDEO, 
and HDMI. 
•Video Mode: Select a mode to optimize the display image based on how the 
projector is being used:
 - Presentation: Best for presentation slides. 
						

							54Using Your Projector
 - Bright: Maximum brightness and contrast.
 - 
Movie: For viewing movie & photo.
 - 
sRGB: Provide a more accurate color representation.
 - 
Custom: User preferred settings.
•Blank Screen: You can select On or Off.
•Aspect Ratio: Allows you to select the aspect ratio to adjust how the image 
appears.
•Brightness: Select value 
to adjust the brightness of the image.
•Contrast: Select value to adjust the display contrast.
•Audio Input: You can select Audio-A, Audio-B, HDMI and Microphone for 
the input source
•Vo l u m e: You can select the value (0~20) for the audio volume
•Speaker: You can select On to enable the audio function or select Off to 
disable the audio function. 
						

							Using Your Projector55
E-mail Alert
• E-mail Alert: You can set whether to be notified by email (Enable) or not 
(Disable).
•To/CC/From: You can enter email address of sender (From) and recipients 
(To/Cc) to receive notification when an abnormality or warning occurs.
• Alert Condition: You can select the abnormalities or warnings to be notified 
by email. When any of the alert conditions occur, an email will be sent to 
the recipients (To/Cc).
•Out going SMTP server, User name and Password should be provided by 
your network administrator or MIS. 
						

							56Using Your Projector
Password Setting
Use Password Setting to set up an administrator password to access the We b  
Management. When enabling password for the first time, set the password before 
enabling it. When the password function is enabled, the administrator password 
will be required for accessing the Web Management.
•New Password: Enter new password
•Confirm Password: Enter password again and submit
•Write Community: Set security for SNMP. Enter password and submit.
 
NOTE: Contact Dell if you forget your administrator password. 
						

							Using Your Projector57
Login Page
•Administrator Password: Enter the Administrator Password and click Login. 
						

							58Using Your Projector
Firmware Update
Use the Firmware Update page to update your projector’s firmware. Press Update 
to start.
• Please wait till the count reaches 0. 
						

							Using Your Projector59
• Wait for 3 seconds and it will proceed to the next step automatically.
• Select the file to upgrade and click the Upgrade button. When upgrading is 
in progress, the Cancel button is disabled. 
						

							60Using Your Projector
• Please wait till the count reaches 0.
• When upgrade is complete, please click the ReLogin button to go back to 
the Web Management Home Page.