Dell S300w Projector Users Guide

							Using Your Projector51
 NOTE: Closed caption option is available for NTSC only.
TEST PATTERN—Test Pattern is used to test focus and resolution.
You can enable or disable the Te s t  Pa t t e r n by selecting Off, 1 or 2. You can also 
invoke the Te s t  Pa t t e r n  1 by pressing and holding down   and   buttons on the 
control panel simultaneously for 2 seconds. You can also invoke the test pattern 2 
by pressing and holding down   and   buttons on the control panel 
simultaneously for 2 seconds.
FACTORY RESET—Select and press   to reset all settings to its factory default, the 
warning message below appears.
Reset items include both computer sources and video source settings. 
Test Pattern 1:
Test Pattern 2: 
						

							52Using Your Projector
Wireless Networking Installation
 NOTE: Your computer must have the following minimum system requirements:
Operating System:
•Windows
Microsoft Windows 2000 with service pack 4 or later, Windows XP Home or 
Professional Service pack 2 32-bit(recommended), Windows Vista 32-bit, and 
Windows 7 Home or Professional 32-bit or 64-bit
•MAC 
MacBook and above, MacOS 10.5 and above
Minimum Hardware:
aIntel Pentium III-800 MHZ (or greater) 
b256MB of RAM required, 512 MB or more recommended. 
c10MB of available hard-disk space 
dSuper VGA supporting 800 x 600 16 bit high color or higher-resolution display 
recommended (PC and display) 
eEthernet adapter (10 / 100 bps) for an Ethernet connection 
fA supported WLAN adapter for a WLAN connection (any NDIS-compliant 
802.11b or 802.11g Wi-Fi device)
Web browser
Microsoft Internet Explorer 6.0 or 7.0 (recommended) or 8.0, Firefox  1.5 or 2.0, 
and Safari 3.0 and above 
						

							Using Your Projector53
In order to use your projector wirelessly, you need to complete the steps below:
1
Install the wireless antenna. See Installing the Antenna on page 10.
2Enable wireless connection on the projector. See WIRELESS / NETWORK 
on page 43.
3Set the Input Select menu then select the Multiple Display to Wireless display. 
See INPUT SELECT on page 35. The 
Wireless Guide Screen shown below 
appears:.
4Take note of the LOGIN CODE, NETWORK NAME (SSID), and IP 
ADDRESS
. You will need these information to login later.
5Connect your computer to the S300w network. 
						

							54Using Your Projector
 NOTE: 
• Your computer must have wireless network function to detect the 
connection.
• When you connect to the 
S300w network, you will lose wireless connectivity 
with other wireless networks.
6Open your internet browser. You will be automatically directed to the S300w 
We b  M a n a g e m e n t
 web page.
 NOTE: If the web page does not load automatically, enter the IP address noted 
from the projector’s screen in the browser’s address bar.
7
The S300w Web Management page opens. For first time use, click Download.  
						

							Using Your Projector55
8Select the appropriate operating system, then click Download.
9Click Run to proceed with the 
one-time installation of the 
software.
 NOTE: You may choose to 
save the file and install it at 
latter time. To do this, click 
Save.
 
NOTE: The following warning messages may appear, select Run and Allow 
respectively. 
						

							56Using Your Projector
10The installation software will launch. Follow the on-screen instructions to 
complete setup.
S300w Wireless Application Software
Once the installation is complete, S300w Wireless Application software will 
launch and will search for the projector automatically. The screen below appears.
Login
To communicate with your projector, enter the Login Code provided for in Step 4 
of Wireless Networking Installation, then click OK.
 
NOTE: If IP Address is not detected, enter the IP Address displayed at the 
bottom left corner of the screen. 
						

							Using Your Projector57
Understanding the Buttons
After a successful login, the following screen appears.
Projecting the Presentation
• To project the presenation, click any of the projection buttons  .
• To pause the presentation, click  . The icon turns green.
• To continue the presentation, click   again.
• To stop the presentation, click  .
Item Description
1Status BarDisplays IP and LOGIN CODE information.
Menu  Click to activate the application menu.
Minimize button Click to minimize the application.
Close button Click to exit the application.
2Controls Toolbar
Full screen Click to project the image in full screen.
Split 1 Click to project the image in the upper left 
corner of the screen.
Split 2 Click to project the image in the upper right 
corner of the screen.
Split 3 Click to project the image in the lower left 
corner of the screen.
Split 4 Click to project the image in the lower right 
corner of the screen.
Stop Click to stop projection.
Pause Click to pause projection.
Refresh Click to refresh projected image.
3Connection Status
Connection Icon Blinks when projection is in progress.
1
2
3 
						

							58Using Your Projector
 NOTE: The following information is for wireless data presentation mode only. 
Image display could be slow or not displayed smoothly if displaying a video clip 
or animation, refer to the frame rate table below for reference.
Frame Rate of Wireless Presentation
 NOTE: 
1The percentage of screen variation is based on 1024 x 768.  Example, display a 320 
x 240 video clip on 1024 x 768 desktop, the screen variation is 9.8%.
2Actuate frame rate could be different depending on factors, such as network 
environment, image content, signal conditions, locations, and CPU performance.
3Under clean WLAN environment using 802.11g connection, and no screen 
stretching.
4Compressed to 1024 x 768 and under 802.11g.
 NOTE: Your computer will not enter S1 (standby mode) / S3 (sleep mode) / S4 
(hibernate mode) when running a wireless presentation.
Using the Menu
Click   to display the menu.
W
EB MANAGEMENT—Click to open the Web Management page. See Managing the 
Projector From Web Management on page 60.Screen Variation % 
1Estimated frame per second 2

						

							Using Your Projector59
SEARCH FOR PROJECTOR—Click to search and connect to wireless projector..
MAKE APPLICATION TOKEN—Click to make application token. See Make 
Application Token on page 79.
INFO—Click to display system information.
ABOUT—Click to display the application version.
EXIT—Click to close the application. 
						

							60Using Your Projector
Managing the Projector From Web 
Management
Configuring the Network Setting
If the projector is connected to a network, you can access the projector using a web 
browser. For configuring the network setting, refer to WIRELESS / NETWORK 
on page 43.
Accessing Web Management
Use Internet Explorer 5.0 and above or Firefox 1.5 and above and enter the IP 
address. You can now access Web Management and manage the projector from a 
remote location.
Home Page
• Access the Web Management Home page by entering the projector’s IP 
address at the web browser. See WIRELESS / NETWORK on page 43.
• Select the language for web management from the list.
• Click any menu item on the left tab to access the page.