Denon D M51dvs Operating Instructions

							81
ENGLISH
(1) Setting the clock (12-hour display)
18USING THE TIMER
1Turn on the power.
2Press the MENU/SET button to display “Ti m e”.
MENU / SET
Main unit
•If the time has not yet been set or if there has been a
power shortage, the time display flashes.
• If the time has been set, the current time is displayed.
3Press the MENU/SET button and hold it in for over 2 seconds.
•The hours position flashes.
Time AM1\b:00
Adj AM1\b:00MENU / SET
Main unit
Example: Setting the current time to “7:30 p.m.”
6Turn the SURROUND/SELECT knob to move to the minutes
position.
Adj PM 7:30SURROUND / SELECTPUSH - PARAM.
Main unit
7
Press the MENU/SET button at the sound of a time signal,
etc.
•The  “30” in the minutes place stops flashing and the
current time is displayed.
Time PM 7:30MENU / SET
Main unit
To check the current time when the regular display is displayed,
press the MENU/SET button once. The current time remains
displayed until some other operation is performed.
The time can be displayed by pressing the MENU/SET button
when the power is in the standby mode. (When this is done, the
set is no longer in the low power consumption standby mode.)
When pressed twice while the time is displayed, the display turns
off and the set is put back in the low power consumption standby
mode.
The current time can also be set when the power is in the standby
mode by pressing the MENU/SET button to display the time then
performing steps  3to  7.
The clock runs by synchronizing with the power supply frequency.
The time may be off by 2 to 3 minutes per month. If so, reset the
time.
BAND
PHONES
VOLUME
ON / STANDBY
DVD SURROUND RECEIVER  ADV-M51
TONE / SDB
FUNCTION MENU / SET+-
SURROUND / SELECTPUSH - PARAM.
1 4,6
2,3,5,7
2
Timer and system operations are possible once the setup procedure has bee\
n completed.
4Turn the SURROUND/SELECT knob to set the hours.
Adj PM 7:00SURROUND / SELECTPUSH - PARAM.
Main unit
5Press the MENU/SET button.
MENU / SET
Main unit
Adj PM 7:00
2Be sure to set the current time. If the current time is not set, the tim\
er standby indicator  does not light and the timer will not function.
2 Be sure to preset the broadcast station before setting the timer. (See page 60.).
2 Everyday timer: The power is switched on and off (standby) once at the\
 same time each day.
Once timer: The power is switched on and off (standby) at the specifie\
d time once only.
Sleep timer: The power can be set to turn off in 120 minutes, 90 minutes\
, or between 60 and 10 minutes in 10 minute steps.
2 If the times set for the everyday timer, once timer and sleep timer overlap, the sleep timer has priority. The once time has priority if the everyday
timer and once timer times overlap.
2 It is not possible to set the timer start and stop times to the same tim\
e.
ON / STANDBY
Main unit
Before setting the timer

Denon  D-M51DVS  User Guide  Manual  
						

							82
ENGLISH
Example 1: Listening to preset station “3” (FM 92.5 MHz) from p.m.12:35 to p.m.12:56 with the everyday timer
BAND
PHONES
VOLUME
ON / STANDBY
DVD SURROUND RECEIVER   ADV-M51
TONE / SDB
FUNCTION MENU / SET+-
SURROUND / SELECTPUSH - PARAM.
1,18 2,3,4,6,8
,
10,12,14,16 
3,5,7,9,11,
13,15,17
(2) Setting the everyday timer and once timer
2 Be sure to set the current time before setting the timer. (See page 81.)
2 Use the everyday timer to switch the power on and off (standby) once a\
t the same time each day.
Use the once timer to switch the power on and off (standby) at the spe\
cified time once only.
2 With the ADV-M51 it is possible to play the tuner, a DVD or a CD with the timer.
2 It is possible to play a DVD, CD, tape, the tuner, MD or the device connected to the AUX terminals with the timer and to \
record  the tuner or
the device connected to the AUX terminals onto an MD recorder or cassett\
e deck using the timer.
Timer playback is not possible for some DVDs. (Most DVDs stop at the men\
u screen.)
1Turn on the power.
2Press the MENU/SET button to display “TIMER”.
MENU / SET
Main unit
3Turn the SURROUND/SELECT knob to display “EVERYDAY”,
then press the MENU/SET button.
• The display switches as follows
each time the SURROUND/SELECT
knob is turned:
TIMER
EVERY\fAY
SURROUND / SELECTPUSH - PARAM.
Main unit
4Press the MENU/SET button.
E FUNCMENU / SET
Main unit
ON / STANDBY
Main unit
The display switches as follows
each time the
SURROUND/SELECT knob is
turned:MENU / SET
Main unit
5Turn the SURROUND/SELECT knob and set the function to
“TUNER”.
SURROUND / SELECTPUSH - PARAM.
Main unit
E TUNER
The function switches as shown below each time thesurround button is pressed.
Functions marked “*” differ according to whether “LINE- 1” or “LINE-2” is set.
DVD TUNER(LINE1)
(LINE2)
(LINE1)
TU
AUX
 (LINE1           2)
TU
 (LINE2)
*
*
*
*
*
:Clockwise turn 
:Counterclockwise turn
6Press the MENU/SET button.
MENU / SET
Main unit
7Turn the SURROUND/SELECT knob and select preset number
“P03”.
P03 FM 9\b.50MSURROUND / SELECTPUSH - PARAM.
Main unit
8Press the MENU/SET button.
• The data for the selected station is stored in the memory
and the unit is set to the timer start time setting mode.
•“ E” and “on” are displayed.
E on AM1\b:00
MENU / SET
Main unit
9
Turn the SURROUND/SELECT knob to set the hours place to
“PM12”.
E on PM1\b:00SURROUND / SELECTPUSH - PARAM.
Main unit
or

Denon  D-M51DVS  User Guide  Manual  
						

							83
ENGLISH
10Press the MENU/SET button.
•The  “PM12” in the hours place is stored in the memory.
MENU / SET
Main unit
E on PM1\b:00
11Turn the SURROUND/SELECT knob and set the minutes
place to “35”.
E on PM1\b:35
SURROUND / SELECTPUSH - PARAM.
12Press the MENU/SET button.
•The start time is stored in the memory and the unit is set
to the timer stop time setting mode.
•“ E” and “off” light.
Main unit
MENU / SET
Main unit
E offAM1\b:00
13
Turn the SURROUND/SELECT knob to set the hours place to
“PM12”.
E offPM1\b:00
SURROUND / SELECTPUSH - PARAM.
Main unit
14Press the MENU/SET button.
•The  “PM12” in the hours place is stored in the memory.
MENU / SET
Main unit
E offPM1\b:00
15Turn the SURROUND/SELECT knob and set the minutes
place to “56”.
E offPM1\b:56
SURROUND / SELECTPUSH - PARAM.
Main unit
16Press the MENU/SET button.
•The stop time is stored in the memory.
MENU / SET
Main unit
17Turn the SURROUND/SELECT knob to display “Eon”.
•The everyday timer is turned on and
the timer standby indicator 
lights. This completes the setting of
the timer.
For more details, see  “Turning the
everyday timer and once timer on
and off” on page 82.
SURROUND / SELECTPUSH - PARAM.
Main unit
1 off/E on
18
ON / STANDBY
Main unit
Turn off the power.
• The standby mode is set.
(The power indicator turns orange.)
• When the timer start time is
reached, the timer operates.
If you make a mistake when setting the
timer.
• Press the stop button at any point
between steps 4 and 15. (The display
returns to as it was in step 3.)
• Press the MENU/SET button repeatedly
to display the item you want to correct,
then correct the item.
• After correcting the item, press the MENU/SET button again
repeatedly to proceed to step 18 and complete the setting of the
timer.
NOTE:
•The timer standby indicator  does not light if the current time
has not been set. Set the current time before setting the timer.
(See page 81.)
BAND
Main unit

Denon  D-M51DVS  User Guide  Manual  
						

							84
ENGLISH
Example 2: Listening to a CD with the once timer
B
BAND
PHONES
VOLUME
ON / STANDBY DVD SURROUND RECEIVER   ADV-M51TONE / SDB
FUNCTION MENU / SET+-
SURROUND / SELECTPUSH - PARAM.
1
3,4,5,7
4,6
2
2
1Turn on the power.ON / STANDBY
Main unit
4Turn the SURROUND/SELECT knob to display “ONCE”, then
press the MENU/SET button.
SURROUND / SELECTPUSH - PARAM.
Main unit
ONCE
The display switches as follows
each time the
SURROUND/SELECT knob is
turned:
2Open the disc holder, load the CD,
then close the disc holder.
Main unit
3Press the MENU/SET button to
display  “TIMER”.MENU / SET
Main unit
TIMER
5Press the MENU/SET button.
•The once timer time setting mode is set.
•“ 1” (once) lights.
1 FUNC
MENU / SET
Main unit
6Turn the SURROUND/SELECT knob and set the function to
“DVD”.
1\fV\fSURROUND / SELECTPUSH - PARAM.
Main unit
7Press the MENU/SET button.
•Timer function, “DVD”, is stored in
the memory.MENU / SET
Main unit
8Now follow steps 9 to 18 under “Setting the everyday timer
and once timer” (pages 82 and 83).
•“ 1” and “on” light when setting the start time.
“1” and “off” light when setting the stop time.
• Turn the once timer on at step  17.
2 Timer playback and recording can be performed when system connections are\
 made between the ADV-M51 and the D-M31 series cassett e
deck (DRR-M31). (Both the everyday and once timer can be used.)
• Timer playback of the cassette deck (when TAPE is set for LINE-2)
• Timer playback of the device connected to the AUX input terminals (when \
AUX is set for LINE-1 or LINE-2)
• Timer recording of radio programs from the ADV-M51 onto the cassette deck (when TAPE is set for LINE-1)
• Timer recording from the device connected to the AUX input terminals onto\
 the cassette deck (when AUX is set for LINE-1 and TAPE is set
for LINE-2)
Timer recording onto the device connected to the AUX input terminals is n\
ot possible. The timer function changes automatically  according
to the function set for LINE-1 and LINE-2.
NOTE:
• For timer recording and playback using the device connected to the AUX i\
nput terminals, note that the ADV-M51 cannot control th e power
of the device or playback operations on it. Make the settings accordingl\
y.
MENU / SET
Main unit

Denon  D-M51DVS  User Guide  Manual  
						

							85
ENGLISH
(3) Turning the everyday timer and once timer on and off
•After the timer has been set using the procedure described under  “(2) Setting the everyday timer and once timer” (pages 82 to 83), turn the
everyday timer and/or once timer on so that the set operations will be p\
erformed.
B
BAND
PHONES
VOLUME
ON / STANDBY DVD SURROUND RECEIVER   ADV-M51TONE / SDB
FUNCTION MENU / SET+-
SURROUND / SELECTPUSH - PARAM.
1
2
1Press the MENU/SET button to set the timer standby setting
mode.
•
The current settings are displayed.
MENU / SET
Main unit
1 on/E on
2
Turn the SURROUND/SELECT knob and select the timer to be
operated.
•The display switches as follows
each time the
SURROUND/SELECT knob is
turned:
1 on/E on
1 on/E off
1 off/E on
1 off/E offBoth the once timer and everyday
timer are activated.
Only the everyday timer is activated.
Only the once timer is activated.
• When either the once or everyday timer is activated, the
timer standby indicator  lights. The display returns to
normal about 4 seconds after the timer standby indicator
is displayed.
SURROUND / SELECTPUSH - PARAM.
Main unit
The timer operation is performed when the SURROUND/SELECTknob has been turned and the timer standby indicator  has
been lit.
SURROUND / SELECTPUSH - PARAM.
Main unit
NOTES:
• The timer standby indicator  does not light if the current time
has not been set. Set the current time before setting the timer.
(See page 81.)
• If the times set for the everyday timer and once timer overlap,
the once time has priority.
• Be sure to set the power to the standby mode when you want
the timer to operate.
Neither the once timer nor the
everyday timer are activated.
If you do not want the timer to operate,
turn the SURROUND/SELECT knob to turn
the timer standby indicator  off.
• If only the once timer is set, the setting
changes as shown below each time the
SURROUND/SELECT knob is turned.SURROUND / SELECTPUSH - PARAM.
Main unit1on/E off f
1off/E of
• If only the everyday timer is set, the setting changes as follows:
1off/E on f
1off/E of
DownloadedCFromCTheatreSystem-Manual.comCManuals
Denon  D-M51DVS  User Guide  Manual  
						

							86
ENGLISH
•If the times set for the everyday timer and once timer overlap, the once\
 time has priority.
(4) Everyday timer and once timer priority
2 Checking the timer settings
• Use the same procedure as when setting the timer to check the timer sett\
ings.
q Press the MENU/SET button to display “TIMER”.
w Turn the SURROUND/SELECT knob to display  “EVERYDAY” or “ONCE”.
e The display switches between the set function, start time, stop time and\
 timer standby indicator each time the MENU/SET button  is pressed.
r The display returns to as it was before the everyday timer or once timer\
 was set about 4 seconds after the timer standby indicator is
displayed.
2 Changing the timer settings
• Reset the timer from the start using the desired settings.
The new settings overwrite the previous settings.
• To change a setting during the process of setting the timer, press the stop button (
2) to return to the “EVERYDAY” or “ONCE” display, then
redo the operation from there.
2 Clearing the timer settings
q Press the MENU/SET button to display “TIMER”.
w Turn the SURROUND/SELECT knob to display  “EVERYDAY” or “ONCE” (the timer whose settings you want to clear).
e While  “EVERYDAY” or “ONCE” is displayed, press the stop button (
2) and hold it in for at least 2 seconds. Those timer settings are clear\
ed.
2 Quitting the timer setting (turning the operation of the timer off)
• Operate as described under  “(3) Turning the everyday timer and once timer on and off ” (page 85) and change the setting to the mode in
which neither the once timer nor the everyday timer are activated ( “1off/Eoff”).
2 If there is a power failure)
• If there is a power failure or the power cord is unplugged from the powe\
r outlet, the time display flashes when the power comes back on.
Reset the current time.
• The once timer settings are deleted. Remake the settings.
• If the everyday timer settings and the tuner presettings have been delet\
ed, reset them.
(5) About the everyday timer and once timer

Denon  D-M51DVS  User Guide  Manual  
						

							87
ENGLISH
•The included remote control unit can be used to turn the power to the st\
andby mode after a maximum of 120 minutes. (Sleep timer )
• Use this function to automatically switch the power to the standby mode \
after a specific amount of time (minutes).
Example:  To set the power to the standby mode in 50 minutesaccording to the clock.\
 Be sure to correct the current time setting .
(6) Setting the sleep timer (remote control unit only)
1Select and play the desired function.
2Press the SLEEP button.
•“120” is displayed and the “SLEEP” indicator flashes.
SLEEP
SOURCE
Remote control unit
     1\b0      SLEEP
The display switches as follows each time the SLEEP button is pressed:
90
120 60 50 3040 20 10
3When the “SLEEP” indicator is flashing, press the SLEEP
button again until “50” is displayed.
•“ 50” is displayed and the “SLEEP” indicator flashes.
SLEEP
SOURCE
Remote control unit
      50      SLEEP
• After 4 seconds, the display returns to as it was before the
sleep timer was set, and the “SLEEP” indicator stops
flashing, remaining lit. (This completes the sleep timer
setting.)
4The power is set to the standby mode 50 minutes later.
To turn the sleep timer off, press the SLEEP button repeatedly until the  “SLEEP” indicator turns off. The sleep timer can also be
turned off by press the power button on the main unit or the
remote control unit to turn the entire system ’s power to the
standby mode.
NOTES:
• If the SLEEP button is pressed while the sleep timer is
operating, the setting returns to 120 minutes. Make the setting
over.
• If the sleep timer and everyday timer settings overlap, the sleep
timer has priority.
8:00p.m. 9:00p.m. 10:00p.m.
8:00p.m. 9:00p.m.
10:00p.m.
ON
OFF
ON OFF+
ON
OFF
8:00p.m. 9:00p.m.10:00p.m.
ON
OFF
ON OFF+
• Also, the everyday timer will not operate if its start time is set
within the time during which the sleep timer is operating.
“SLEEP” indicator off
Everyday timer
once timer setting
Sleep timer setting
Timer operation If the timers overlap like this, the timer operates as follows:
Everyday timer
once timer setting
Sleep timer setting
Does not operate
• The remaining time of the sleep timer can be checked with the
STATUS button.
Does not operate
ON / STANDBYOFF
Main unit Remote control unit
SLEEP
SOURCE
Remote control unit
+
-
+
-
A-B REPEAT
SEARCH MODE
ON
OFF
REPEAT RANDOM
CLEAR ZOOM
SLIDE MODE
PROG/ DIRECT MEMO BAND
MODE
FUNCTION
SURROUND
INPUT MODE
TEST TONE TUNER
CH
3
-+
21654
987
0
/ 10CALL+
10
VCR
NTSC/PAL
SLEEP
ENTER
CD SRS
EDIT
/
MENU
CHARAC.
REC
TIME
TITLE
TUNING /TV VOL
TV CH TV CH
TUNER
DVD
MD / LINE-1 TAPE / LINE-2
AUTO DECODE
VIRTUAL
DIRECT 5CH STEREO
STEREO D.AUXT     V
T V  IN
SOURCE2,3
A / V
SYSTEM MD
CDR TAPE
TUNER
TV / VCR
IN/
SURR.
IN /
SURR.DVD
Set the remote
control selector
switches to A/V
and IN/SURR..

Denon  D-M51DVS  User Guide  Manual  
						

							88
ENGLISH
SETUP  MENU
QUICK  SETUP
SYSTEM  SETUP
DVD  SETUP
EXIT  SETUP
SELECT : DECISION : ENTER  BUTTON
DENON  
19CHANGING THE DEFAULT SETTINGS (DVD)
Remote control unit
Remote control unit
ENTER
1
2In the stop mode, press the SETUP button.
At the Setup Menu, use the • and \fcursor buttons to select
“DVD SETUP” and press the ENTER button.
The setup (default settings) screen  “DVD SETUP MENU”
appears.
• DISC SETUP
Use this to set the language to be used when playing the
disc.
If the set language is not offered on that disc, the discs
default language is set.
• OSD SETUP
Use this to set the wall paper color.
• VIDEO SETUP
Use this to set this unit screen mode.
(TV aspect and TV type.)
• AUDIO SETUP
Use this to set this unit audio output mode.
(Digital and LPCM output settings.)
• RATINGS
Use this to disable playback of adult DVDs so that children
cannot watch them. Note that playback of adult DVDs
cannot be disabled if the rating level is not recorded on the
DVD, but that it is possible to disable playback of all DVDs.
• OTHER SETUP
Closed captions (subtitles) and the time interval for playing
still pictures can be set.
Use the 0and 1cursor buttons to select the desired setting
item, then press the ENTER button.
To exit the DVD setup mode
Use the 0and 1cursor buttons to select  “EXIT SETUP”, then press the ENTER button. It is also possible to quit by pressing t\
he SETUP
button on the remote control unit.
ENTER
SETUP
2 The initial setting that was set prior to shipping from the factory can \
be changed.
The setting contents are maintained until they are next changed even whe\
n the power is switched off.
DECISION : ENTER  BUTTON
SELECT : NEXT  DVD  MENU
DISC  SETUP
DISC  MENUSSUBTITLE
DIALOG
ENGLISH
ENGLISH
ENGLISH
d
Remote control unit
d
Remote control unit
d
Remote control unit

Denon  D-M51DVS  User Guide  Manual  
						

							89
ENGLISH
Use the 0and 1cursor buttons to select the “DISC
SETUP”, then press the ENTER button.
• DIALOG
Use this to set the language of the sound output from
the speakers.
• SUBTITLE
Use this to set the language of the subtitles displayed on
the TV.
• DISC MENUS
Use this to set the language of the menus recorded on
the disc (top menu, etc.).
To exit the disc setup mode
Use the  •and 
\fcursor buttons to select “> NEXT DVD
MENU”, then press the ENTER button.
Use the  •and 
\fcursor buttons to select the desired
setting, then press the ENTER button.
2 When 
“DIALOG” is selected:
• ENGLISH (Factory default)
Select this when you want to play the DVD with the
sound in English.
• FRENCH
Select this when you want to play the DVD with the
sound in French.
• SPANISH
Select this when you want to play the DVD with the
sound in Spanish.
• GERMAN
Select this when you want to play the DVD with the
sound in German.
• JAPANESE
Select this when you want to play the DVD with the
sound in Japanese.
• OTHERS
The sound is played in the language input with the number
buttons. (See the table of language numbers on page 91.)
DECISION : ENTER  BUTTON
SELECT : NEXT  DVD  MENU
DISC  SETUP
DISC  MENUSSUBTITLE
DIALOG
ENGLISH
ENGLISH
ENGLISH
Remote control unit
Remote control unit
ENTER
DISK  SETUP
DIALOG ENGLISH
FRENCH
SPANISH
GERMAN
JAPANESE
OTHERS
SELECT :
DECISION : ENTER  BUTTON
(1)  “DISC SETUP” is selected
1
See page 88.
2
3
4
d
Remote control unit
Remote control unit
ENTER
d

Denon  D-M51DVS  User Guide  Manual  
						

							90
ENGLISH
To exit the dialog mode
Press the ENTER button, you can go back to the previous
screen.
2 When 
“SUBTITLE” is selected:
• OFF (Factory default)
Select this if you do not want to display the subtitles. (For
some discs it is not possible to turn off the subtitle
display.)
• ENGLISH
Select this when you want to play the DVD with the
subtitles in English.
• FRENCH
Select this when you want to play the DVD with the
subtitles in French.
• SPANISH
Select this when you want to play the DVD with the
subtitles in Spanish.
• GERMAN
Select this when you want to play the DVD with the
subtitles in German.
• JAPANESE
Select this when you want to play the DVD with the
subtitles in Japanese.
• OTHERS
Subtitles are played in the language input with the number
buttons. (See the table of language numbers on page 91.)
To exit the subtitle mode
Press the ENTER button, you can go back to the previous
screen.
2 When 
“DISC MENUS” is selected:
• ENGLISH (Factory default)
Select this when you want to display the menus in
English.
• FRENCH
Select this when you want to display the menus in
French.
• SPANISH
Select this when you want to display the menus in
Spanish.
• GERMAN
Select this when you want to display the menus in
German.
• JAPANESE
Select this when you want to display the menus in
Japanese.
• OTHERS
The menu screen is played in the language input with the
number buttons. 
(See the table of language numbers on page 91.)
To exit the disc menus mode
Press the ENTER button, you can go back to the previous
screen.
DECISION : ENTER  BUTTON
DISC  SETUP
SUBTITLE OFF
ENGLISH FRENCH
SPANISH
GERMAN
JAPANESE OTHERSSELECT :
DISC  SETUP
DISC MENUS ENGLISH
FRENCH
SPANISH
GERMAN
JAPANESE
SELECT : OTHERS
DECISION : ENTER  BUTTON
4
Remote control unit
Remote control unit
ENTER
d
Remote control unit
Remote control unit
ENTER
d

Denon  D-M51DVS  User Guide  Manual