Dukane Data Video Projector 8106b Users Manual

9
ENGLISH
Using the cable cover
Utilize the cable cover as the guard and blind for the connecting parts.\
1. Connect the signal cables and the power cord to the projector first.
2. Combine parts as shown in figure,  
and assemble the cable cover. 
3. Insert the three knobs on the cable cover into the three holes on the pr\
ojector 
as shown in the figure. Pass the cables through the holes on the botto\
m of 
the cable cover. 
CAUTION  ► Be careful not to pinch the cables in the cable cover, to 
prevent...

10
Preparing for the remote control
Please insert the batteries into the remote control before using it. If \
the remote 
control starts to malfunction, try to replace the batteries. If you will\
 not use the 
remote control for long period, remove the batteries from the remote con\
trol and 
store them in a safe place.
1. Holding the hook part of the battery 
cover, remove it.
2. Align and insert the two AA batteries 
(
HITACHI MAXELL or HITACHI MAXELL 
ENERGY, Part No.LR6 or R6P
) according to their...

11
ENGLISH
Turning on the power
1. Make sure that the power cord is firmly 
and correctly connected to the projector 
and the outlet.
2. Make sure that the POWER indicator is 
steady orange.
3. Confirm that there is nothing that the  
lens door hits while opening. Press the  
STANDBY/ON button on the projector or  
the remote control. The lens door opens, the  
projection lamp lights up, and the  POWER  
indicator begins to blink green. When the  
power is completely on, the indicator will stop blinking...

12
Adjusting the projector's elevator
The projector has Front foot for inclinations and Rear foot for horizont\
als. Spacers 
on the each elevator foot are installed at the time of shipment, and pro\
jector is in a 
condition to be able to just project. If necessary, detach the spacer, and the elevator 
feet can be manually twisted to make more precise adjustments.
Displaying and switching the image
Press the INPUT button on the projector. Each time you press the button, the 
projector switches its...

13
ENGLISH
Focusing
Use the FOCUS + and FOCUS - buttons on 
 
the projector or remote control to adjust the  
screen focus. 
Selecting an aspect ratio
Each time you press the ASPECT button on 
 
the remote control, it switches the aspect  
ratio of the image, in turn.
Zooming
Use the D-ZOOM + and D-ZOOM - buttons 
 
on the remote control to adjust the screen size.
Adjusting the picture position
After pressing the POSITION button on the remote control, use the ▲, ▼, ◄ and 
► buttons. Press the POSITION...

14
Turning off  the power
1. Press the STANDBY/ON button on the 
projector or the remote control.
The message “Power off?” will appear on 
the screen for about 5 seconds.
2. Confirm that there is nothing that the 
lens door hits while closing. Press the 
STANDBY/ON button again while the 
message appears. 
The projector lamp will go off, and the 
POWER indicator will begin blinking in 
orange. The lens door will close right after the 
lamp goes off.
However, to maintain better picture quality, the lens...

15
ENGLISH
Replacing the lamp
A lamp has finite product life. Using the lamp for long periods of time could cause 
the pictures darker or the color tone poor. Note that each lamp has a different 
lifetime, and some may burst or burn out soon after you start using them. 
Preparation of a new lamp and early replacement are recommended. To prepare 
a new lamp, make contact with your dealer and tell the lamp type number.
Type number : 456-8105B
1.  Turn the projector off, and unplug the power cord. 
Allow the...

16
 HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE
WARNING  ►The projector uses a high-pressure mercury glass lamp. The lamp 
can break with a loud bang, or burn out, if jolted or scratched, handled\
 while hot, or 
worn over time. Note that each lamp has a different lifetime, and some may burst or 
burn out soon after you start using them. In addition, if the bulb burst\
s, it is possible 
for shards of glass to fly into the lamp housing, and for gas containi\
ng mercury and 
dust containing fine particles...

17
ENGLISH
The air filter has two kinds of filters inside. Please check and cle\
an the air filter periodically. 
When the indicators or a message prompts you to clean the air filter, comply with it as soon 
as possible. If the filters are damaged or heavily soiled, replace the\
m with the new ones. To prepare the new filters, make contact with your dealer and tell the fo\
llowing type number.
Type number : UX37191 (Filter set)
When you replace the lamp, please replace the air filter. An air filter of specified...

18
Caring for the mirror and lens
If the projection mirror or lens is flawed, soiled or fogged, it could\
 cause deterioration 
of display quality. Please take care of the mirror and lens, being cautious of handling. 
1.Turn the projector off and unplug the power cord 
from the power outlet. And cool the projector down 
by leaving it for a while as it is.
2.The lens door can be opened manually.
Please hold both side of the lens door and slowly 
open it until it is locked with clicking sound.
3.Use an air...