Dukane Imagepro 8776-W Lcd Projector Users Manual

							
39

SCREEN Menu
SCREEN Menu
ItemDescription
LANGUAGE
Using the buttons ▲/▼ switches the OSD (On Screen Display) language.
MENU POSITIONUsing the buttons ◄/►/▲/▼ adjusts the menu position.To quit the operation, press the MENU button on the remote control 
or keep no operation for about 0 seconds.
BLANK
Using the buttons ▲/▼ switches the mode for the blank screen.
The blank screen is a screen for the temporarily blanking feature 
(24). It is displayed by pressing the BLANK button on the remote control.
MyScreen ó ORIGINAL ó BLUE ó WHITE ó BLACK
  
MyScreen is a screen you can register as a desired screen. The ORIGINAL screen is the existing standard screen. BLUE, WHITE and BLACK are non-patterned (plain) screens in each color.
• To avoid remaining as an afterimage, the MyScreen and the ORIGINAL screens will change to the BLACK screen after several minutes.
• For the MyScreen, please refer to the MyScreen item (40).
With  the  SCREEN  menu,  the  items  shown  in  the  table 
below can be performed. 
Select an item using the cursor buttons ▲/▼ on the 
projector or remote control, and press the cursor button ► 
on the projector or remote control, or the ENTER button 
on the remote control to execute the item. Then perform it 
referring to the following table. 
/07=4)$?
+/#)5672
2+%674+0276
126+10/+7#5;/07
5%40
5.%6.#0)7#)0).+5*/07215+6+1056#467214+)+0#./[5ETGGP/[5ETGGP.QEM67401((
5174%0#//55#)674010
$.#0-$.#%-
SUOMI ó POLSKI ó TÜRKÇE 
ENGLISH ó FRANÇAIS ó DEUTSCH ó ESPAÑOL ó ITALIANO 
NORSK ó NEDERLANDS ó PORTUGUÊS ó 日本語 
    ó    ó        ó SVENSKA ó 
   
						

							
40

SCREEN Menu
ItemDescription
START UP
Using the buttons ▲/▼ switches the mode for the start-up screen.
The start-up screen is a screen displayed when no signal or an unsuitable signal is detected.MyScreen ó ORIGINAL ó TURN OFF
    MyScreen is a screen you can register as a desired screen.The ORIGINAL screen is the existing standard screen. When TURN OFF is selected, the BLACK screen is used.• To avoid remaining as an afterimage, the MyScreen and the ORIGINAL screens will change to the BLANK screen after several minutes. If also the BLANK screen is the MyScreen or ORIGINAL, it will change to the BLACK screen.
• For the MyScreen, please refer to the item MyScreen below. For 
the BLANK screen, please refer to the BLANK item (39).• This function will be unavailable and fixed to Myscreen when MyScreen Password in the Security Menu is on. 
MyScreen
This item functions for capturing the MyScreen of the blank screen and the start-up screen. Please execute displaying the input including the picture you want to capture.
.  Selecting this item displays a dialog titled “MyScreen”. It will a\
sk you if you start capturing the picture from the current screen. Please wait for the target picture to be displayed, and press the ENTER button on the remote control when the picture is displayed. The picture will freeze and the frame for capturing appears.      To stop performing, press the RESET or ESC button on the 
remote control. 
.  Using the buttons ◄/►/▲/▼ adjusts the frame position. Please move the frame to the position of the picture which you want to use.      
The frame may not be able to be moved for some input signals.
     To start registration, press the ENTER button on the remote control.      
To restore the screen and return to the previous dialog, press the RESET or ESC button on the remote control.Registration takes several minutes. When the registration is completed, the registered screen and the message “MyScreen registration is finished.” are displayed for several seconds. If the registration failed, the message “A capturing error has occurred. Please try again.” is displayed.• This function will be unavailable when MyScreen Password in the Security Menu is on. NOTE : The KEYSTONE cannot be adjusted while using the MyScreen function.
MyScreen Lock
Using the buttons ▲/▼ turns on/off the MyScreen lock function.TURN ON ó TURN OFFWhen the TURN ON is selected, the item MyScreen is locked. Use 
this function for protecting the current MyScreen.• This function will be unavailable when MyScreen Password in the Security Menu is on. 
SCREEN Menu (continued) 
						

							
4

SCREEN Menu
ItemDescription
MESSAGE
Using the buttons ▲/▼ turns on/off the message function.
TURN ON ó TURN OFF
When the TURN ON is selected, the following message function works.“AUTO IN PROGRESS” while automatically adjusting”NO INPUT IS DETECTED””SYNC IS OUT OF RANGE”"Searching….” while searching for the input”Detecting….” while an input signal is detectedThe indication of the input signal displayed by changing The indication of the aspect ration displayed by changingThe indication of the My Memory displayed by changing The indication of the Picture Mode displayed by changingThe indication of "FREEZE" and "II" while freezing the screen by pressing the FREEZE button.• When the TURN OFF is selected, please remember if the picture is freezing. Do not mistake freezing for a malfunction (24).
SOURCE NAME
Each input port for this projector can have a name applied to it.(1) Use the ▲/▼ buttons on the SCREEN menu to select SOURCE NAME and press the ► button. The SOURCE NAME menu will be displayed.
(2) Use the ▲/▼ buttons on the SOURCE NAME menu to select the port to be named and press the ► button. The SOURCE NAME dialog will be displayed.
(3) The current name will be displayed on the first line. Use the ◄/►/▲/▼ and ENTER or INPUT buttons to select and enter characters. The RESET button can 
be used to erase  character at a time. The 
name can be a maximum of 6 characters.
(4) To change an already inserted character, press the ▲ button while the cursor is on the [A-N] row to move the cursor to the name displayed on the first line and use the ◄/► buttons to select character to be changed. Once a character in the 
name is selected use the ▼ button to move the cursor back down to the character entry area to select and enter characters as described above.
(5) Select  and press the ENTER or INPUT buttons when finished entering text.To revert to the previous name without 
saving changes press the ESC or ◄ button and the INPUT button simultaneously.
SCREEN Menu (continued)
0#/4)$4)$#$%&()*+,-./0123456789:;
						

							
4

OPTION Menu
OPTION Menu
ItemDescription
AUTO SEARCH
Using the buttons ▲/▼ turns on/off the automatic signal search function.
TURN ON ó TURN OFF
When the TURN ON is selected, detecting no signal automatically cycles through input ports in the following order. The search is started from the current port. Then when an input is found, the projector will stop searching and display the image. 
RGB IN ð RGB IN ð MIU ð COMPONENT VIDEO ð S-VIDEO ð VIDEO     
AUTO KEYSTONE
Using the buttons ▲/▼ turns on/off the automatic keystone function.
TURN ON ó TURN OFF
TURN ON : Automatic keystone distortion correction will be executed whenever changing the slant of the projector.
TURN OFF : This function is disabled. Please execute the AUTO KEYSTONE EXECUTE in the SETUP Menu for automatic keystone distortion correction.
 When the projector is suspended from the ceiling this feature will not function properly so select TURN OFF.This function will be unavailable when Transition Detector is on (50).
AUTO ON
Using the buttons ▲/▼ turns on/off the AUTO ON function.
TURN ON ó TURN OFF
When set to TURN ON, the lamp will only be automatically turned on when the Power switch is turned on after the power was turned off by Power switch last time. The lamp will not be automatically turned on when the Power switch is turned on if the lamp was turned off with the following procedures.• The lamp was turned off with a remote control, projector button, or power turn off command.• The lamp was turned off with an AUTO OFF function (43).• The lamp was turned on by an AUTO ON function and was turned off about 30 minutes after no signal had been detected.
When no input is detected after the power on and AUTO OFF time is set to 0, the projector will be turned off after about 30 minutes passed.When no input is detected after the power on and AUTO OFF time is set to 
 to 99, the projector will be turned off after the passed time reaches at the 
set time.If one of the projector's buttons or the remote control buttons is press\
ed or one of the commands (except get commands) is transmitted from the control port during the corresponding time, projector will not be turned\
 off.
With  the  OPTION  menu,  the  items  shown  in  the  table  below  can be performed. Select  an  item  using  the  cursor  buttons  ▲/▼  on  the  projector  or remote  control,  and  press  the  cursor  button  ►  on  the  projector or  remote  control,  or  the  ENTER  button  on  the  remote  control  to execute  the  item,  except  for  the  items  LAMP  TIME  and  FILTER TIME. Then perform it referring to the following table.
/07=4)$?
2+%674
5.%6

+/#)5672
+0276
126+10/+7#5;/07
5%40
#7611((OKP.#/26+/J(+.646+/J
#7615#4%*67401((#761-;561067401((#7611067401((
/;$76610548+%5%74+6; 
						

							
43

ItemDescription
AUTO OFF
Using the buttons ▲/▼ adjusts the time to count down to automatically turn the projector off.
Long (max. 99 minutes) ó Short (min. 0 minute = DISABLE)
AUTO OFFENABLE
AUTO OFFDISABLE0
When the time is set to 0, the projector is not turned off automatically.When the time is set to  to 99, and when the passed time with no-signal or an unsuitable signal reaches at the set time, the projector lamp will be turned off. If one of the projector's buttons or the remote control buttons is press\
ed or one of the commands (except get commands) is transmitted to the control port during the corresponding time, projector will not be turned\
 off.Please refer to the section “Turning off the power” (19).
LAMP TIME
The lamp time is the time counted after the last resetting. It is shown in the OPTION menu as the usage time of the lamp.Pressing the RESET button on the remote control or the button ► of the projector displays a dialog. To reset the lamp time, select the RESET using the button ▲.
RESET  CANCEL
• Please reset the lamp time only when you have replaced the lamp, for a suitable indication about the lamp.• For the lamp replacement, see the section "Lamp" (57, 58).
FILTER TIME
The filter time is the time counted after the last resetting. It is shown in the OPTION menu as the usage time of the air filter.Pressing the RESET button on the remote control or the button ► of the projector displays a dialog. To reset the filter time, select the RESET using the button ▲.
RESET  CANCEL
• Please reset the filter time only when you have cleaned or replaced the air filter, for a suitable indication about the air filter.• For the air filter cleaning, see the section "Air filter" (59, 60).
MY BUTTONSets  the  assigned  function  for  the  MY  BUTTON  and 
  buttons  on 
the included remote control.
• RGB: Sets port to RGB.
• RGB: Sets port to RGB.
• MIU: Sets port to MIU.• COMPONENT: Sets port to COMPONENT.• S-VIDEO: Sets port to S-VIDEO.• VIDEO: Sets port to VIDEO.• e-SHOT: Displays the e-SHOT menu (53).• INFORMATION: Displays INPUT INFORMATION (45).• AUTO KEYSTONE EXECUTE: Performs automatic KEYSTONE correction (37).• MY MEMORY: Loads MY MEMORY settings (31).• PICTURE MODE: Changes the PICTURE mode (27).• FILTER RESET: Displays the filter time reset confirmation dialogue (43).• VOLUME+: Sets the volume up.• VOLUME-: Sets the volume down.
OPTION Menu
OPTION Menu (continued) 
						

							
44

ItemDescription
SERVICE
Selecting this item displays the SERVICE menu.Select an item using the buttons ▲/▼, and press the button ► or the ENTER button on the remote control to execute the item.
FAN SPEED ó AUTO ADJUST ó GHOST ó FILTER MESSAGE ó KEY LOCK 
FACTORY RESET ó INFORMATION ó REMOTE FREQ.
FAN SPEEDUsing the buttons ▲/▼ switches the rotation speed of the cooling fans. The HIGH is the mode for use at highlands etc. Note that the projector is noisier when the HIGH is selected.
HIGH ó NORMAL
AUTO ADJUSTUsing the buttons ▲/▼ enables/disables the automatic adjustment.When DISABLE is selected, the automatic adjustment feature is disabled, although rough adjustment is automatically performed depending on the basic setting.
ENABLE ó DISABLE
• Depending on conditions, such as input image, signal cable to the projector, environment around the projector, etc., the automatic adjustment may not work correctly.  In such a case, please choose DISABLE to disable the automatic adjustment, and make adjustment manually.
GHOST
1.  Select a color element of ghost using the buttons ◄/►. 
.  
Adjust the selected element using the buttons ▲/▼ to disappear ghost.
FILTER MESSAGEUse the ▲/▼ button to set the timer for the interval to show the message for cleaning up the air filter. 50h ó  00h ó 00h ó 300h ó TURN OFF
After selecting “50h”, “00h”, “00h”, or “300h”, the message 
“REMINDER *** HRS PASSED AFTER THE LAST FILTER CHECK” will appear after the timer reaches the interval time set by the menu. (63) When the “TURN OFF” is chosen, the air filter cleaning message will not appear.• Please check and clean the air filter periodically, even if there is no message. If the air filter becomes to be blocked by dust or others, the internal temperature will rise, which could cause malfunction, or reduce the lifetime of the projector.•  It is recommended to choose “00h” in general. Please be careful with the operating environment of the projector and the condition of the air filter, especially when the “200h”, “300h” or “TURN OFF” is chosen. 
KEY LOCKUsing  the  buttons  ▲/▼  turns  on/off  the  key  lock  feature.  When TURN  ON  is  selected,  the  buttons  on  the  projector  except  the STANDBY/ON button are locked.TURN ON ó TURN OFF• Please use to avoid a mischief and touching accidentally. This function does not have any effect on the remote control.
OPTION Menu (continued)
OPTION Menu 
						

							
45

ItemDescription
SERVICE
REMOTE FREQ.Use the ▲/▼ button to change the Projector's remote sensor setting (18).
:NORMAL 
ó  :HIGH
Items with a checkmark are on. The factory default setting is for 
both :NORMAL and :HIGH to be on. If the remote control does 
not function correctly set the this to either only  or only  as 
described in Remote Control Settings (18).Neither can be turned off at the same time.
INFORMATIONSelecting this item displays a dialog titled “INPUT INFORMATION”. 
It shows the information about the current input.
INPUT-INFORMATIONRGB04x768 @60HzFRAME LOCK
INPUT-INFORMATIONS-VIDEOSECAMAUTO
INPUT-INFORMATIONCOMPONENT576i @50SCART RGB
• The “FRAME LOCK” message on the dialog means the frame lock function is working. 
• The “SCART RGB” message means the COMPONENT VIDEO port is working as a SCART RGB input port. Please refer to the 
COMPONENT item in INPUT menu. (35)
• This item can't be selected for no signal and sync out.
FACTORY RESETSelecting RESET using the button ▲ performs this function. By this function, all the items in all of menus will collectively return to\
 the initial setting. Note that the items LAMP TIME, FILTER TIME, LANGUAGE and SECURITY are not reset.
RESET  CANCEL
OPTION Menu (continued)
OPTION Menu 
						

							
46

ItemDescription
SECURITY
This projector is equipped with security functions.User registration is required before using the security functions.Please contact your local dealer.
1. Using Security Features
1.1 Inputting the PASSWORD
1.1-1  Use the ▲/▼ buttons on the OPTION menu to select SECURITY and press the ► button. The ENTER PASSWORD box will be displayed. The factory default PASSWORD is 
3046. This PASSWORD can be changed (. 
Changing the PASSWORD). 
NOTE  :  It is strongly recommended the factory default PASSWORD to be changed as soon as possible.
1.1-2   Use the ▲/▼/◄/► buttons to enter the registered PASSWORD. Move the cursor to the right side of the ENTER PASSWORD BOX and press the ► button to display the SECURITY menu. If an incorrect PASSWORD is input the ENTER PASSWORD BOX will be displayed again. If incorrect PASSWORD is input 3 times the projector will turn off. Afterwards the projector will turn off every time an incorrect PASSWORD is input.
1.2 Changing the PASSWORD
1.2-1  Use the ▲/▼ buttons on the SECURITY menu to select SECURITY PASSWORD CHANGE and press the ► button to display the ENTER NEW PASSWORD BOX.
1.2-2   Use the ▲/▼/◄/► buttons to enter the new 
PASSWORD.
.-3   Move the cursor to the right side of the 
ENTER NEW PASSWORD BOX and press the ► button to display the NEW PASSWORD AGAIN BOX, enter the same PASSWORD again. 
.-4   Move the cursor to the right side of the NEW 
PASSWORD AGAIN BOX and press the ► button and the NOTE NEW PASSWORD BOX 
will be displayed for about 0 seconds, please 
make note of the PASSWORD during this time. Pressing the ENTER button on the remote control or INPUT button on the projector will close the NOTE NEW PASSWORD BOX.
NOTE  :  Please do not forget your PASSWORD.
OPTION Menu (continued)
OPTION Menu
5%74+6;0642#55914&
0:6

37+6
ENTER PASSWORD BOX
5%74+6;
5%74+6;2#55914&%*#0)/[5ETGGP2#55914&67401((2+0.1%-67401((64#05+6+10&6%61467401((
SECURITY MENU
5%74+6;064092#55914&
0:6

37+6ENTER NEW PASSWORD BOX
5%74+6;092#55914&#)#+0
1-

%#0%.NEW PASSWORD AGAIN BOX
5%74+6;016092#55914&
:+6

064NOTE NEW PASSWORD BOX 
						

							
47

ItemDescription
SECURITY
1.3 If you have forgotten your PASSWORD
.3-  Follow the procedure in .- to display the ENTER PASSWORD BOX.
.3-   While the ENTER PASSWORD BOX is 
displayed, press and hold the RESET button on the remote control for about 3 seconds or press and hold the INPUT and ► buttons on the projector for about 3 seconds.
The 0 digit Inquiring Code will be displayed. 
NOTE: If there is no key input for about 55 seconds while the Inquiring Code is displayed the menu will 
close. If necessary repeat the process from .3-.
.3-3   Contact your dealer with the  0 digit Inquiring Code. Your PASSWORD 
will be sent after your user registration information is confirmed.
2. Using the MyScreen PASSWORD Function
The MyScreen PASSWORD function can be used to prohibit access to the MyScreen function and prevent the currently registered MyScreen image from being overwritten.
2.1 Turning on the MyScreen PASSWORD 
Function
2.1-1   Use the ▲/▼ buttons on the SECURITY menu to select MyScreen PASSWORD and press the ► button to display the MyScreen PASSWORD on/off menu.
2.2 Setting the PASSWORD
.-  Display the MyScreen on/off menu using the 
procedure in .-.
2.2-2   Use the ▲/▼ buttons on the MyScreen 
PASSWORD on/off menu to select TURN ON.The ENTER PASSWORD BOX (small) will be displayed.
2.2-3  Use the ▲/▼/◄/► buttons to enter the 
PASSWORD. Move the cursor to the right side of the ENTER PASSWORD BOX (small) and press the ► button to display the CHECK PASSWORD BOX, enter the same PASSWORD again.
5%74+6;2#55914&

+PSWKTKPI%QFG
OPTION Menu (continued)
OPTION Menu
/[5ETGGP0642#55914&
0:6

37+6
Inquiring Code (PASSWORD)
/[5ETGGP%*%-2#55914&
0:6

37+6CHECK PASSWORD BOX
/[5ETGGP2#55914&
67401067401((
MyScreen PASSWORD on/off menu
ENTER PASSWORD BOX (small) 
						

							
48

ItemDescription
SECURITY
.-4  Move the cursor to the right side of the CHECK PASSWORD BOX and press the ► button to 
display the PASSWORD for about  0 seconds, 
please make note of the PASSWORD during this time. After the PASSWORD has displayed 
for about 0 seconds the screen will return to 
the MyScreen PASSWORD on/off menu.Pressing the ENTER button on the remote control or INPUT button on the projector will close the PASSWORD box.When a PASSWORD is set for MyScreen:
• The MyScreen registration function (and menu) will be unavailable.
• The START UP setting will be locked on MyScreen (and the menu will be unavailable).Turning the MyScreen PASSWORD off will allow normal operation of both  functions.
NOTE  :  Please do not forget your MyScreen PASSWORD.
2.3 Turning the PASSWORD off
.3-   Follow the procedure in .- to display the MyScreen PASSWORD on/off menu.
.3-   Select TURN OFF to display the ENTER PASSWORD BOX (large). 
Enter the registered PASSWORD and the screen will return to the MyScreen on/off menu. If an incorrect PASSWORD is input the menu will close. If necessary repeat 
the process from .3-.
2.4 If you have forgotten your PASSWORD
.4-  Follow the procedure in .- to display the MyScreen PASSWORD on/off menu.
.4-   Select TURN OFF to display the ENTER 
PASSWORD BOX (large). The 0 digit 
Inquiring Code will be displayed inside the BOX.
.4-3   Contact your dealer with the 0 digit Inquiring 
Code. Your PASSWORD will be sent after your user registration information is confirmed.
3. Using the PIN LOCK FunctionPIN LOCK is a function which prevents the projector from being used unle\
ss a registered Code is input.3.1 Registering the PIN Code
3.1-1  Use the ▲/▼ buttons on the SECURITY menu to select PIN LOCK and press the ► button or the ENTER button to display the PIN LOCK on/off menu.
3.1-2   Use the ▲/▼ buttons on the PIN LOCK on/off 
menu to select TURN ON and the PIN BOX will be displayed. 
0:637+6
+PSWKTKPI%QFG         
/[5ETGGP0642#55914&
OPTION Menu (continued)
OPTION Menu
/[5ETGGP%1/2.6
:+6

064
ENTER PASSWORD BOX (large)
PASSWORD BOX
2+0.1%-
67401067401((
PIN LOCK on/off menu