Dukane Projector 6132HD User Manual

							64
English ...
Appendices
ModesResolution (dots) V.Frequency
[Hz] H.Frequency
[KHz]
VGA640x4806031.5
SVGA800x6006037.9
XGA1024x7686048.4
QuadVGA1280x9606060.0
SXGA1280x10246064.0
SXGA+1400x10506065.3
(1) HDMI - PC Signal
 HDMI Digital
(2) HDMI - Extended Wide timing
ModesResolution (dots) V.Frequency
[Hz] H.Frequency
[KHz]
HD 1280x720 6044.8
HD 1280x720 12092.9
WXGA 1280x768 6047.8
WXGA 1280x800 6049.6
WXGA 1360x768 6047.7
WXGA 1366x768 6047.7
WXGA+ 1440x900 6059.9
WXGA++ 1600x9006059.9
WSXGA+ 1680x1050 6065.3
Full HD 1920x1080(1080P) 6067.5 
						

							65... English
Appendices
(3) HDMI - Video Signal
ModesResolution (dots) V.Frequency
[Hz] H.Frequency
[KHz]
480i 720x480(1440x480) 59.94(29.97)15.7
576i 720x576(1440x576) 50(25)15.6
480p 640x48059.9431.5
480p 720x48059.9431.5
576p 720x576 5031.3
720p 1280x720 6045.0
720p 1280x720 5037.5
1080i 1920x1080 60(30)33.8
1080i 1920x1080 50(25)28.1
1080p 1920x108023.97/24 27.0
1080p 1920x1080 6067.5
1080p 1920x1080 5056.3
(4) HDMI – 3D Timing
ModesResolution (dots) V.Frequency
[Hz] H.Frequency
[KHz]
720p (Frame Packing) 1280x720 5037.5
720p (Frame Packing) 1280x720 60
45.0
1080p (Frame Packing ) 1920x10802427.0
720p (Top and Bottom ) 1280x7205037.5
720p (Top and Bottom ) 1280x7206045.0
1080p (Top and Bottom) 1920x10802427.0
1080i (Side by Side (Half)) 1920x1080
50(25)28.1
1080i (Side by Side (Half)) 1920x1080
60(30)33.8
Graphic source monitor range limitsHorizontal scan rate:30k-100kHz
Vertical scan rate:50-120Hz
Max. pixel rateAnalog:162MHz 
Digital:165MHz
(5) MHL signal table
SignalResolution (dots) Aspect RatioRefresh Rate (Hz)
VGA 640x480 4:359.94/60
HDTV (1080p) 1920x108016:923.98/24
HDTV (1080i) 1920x108016:950/59.94/60
HDTV (720p) 1280x72016:950/59.94/60
SDTV (480p) 720x4804:3/16:959.94/60
SDTV (576p) 720x5764:3/16:9 50
MHL signal table - Mobile High-Definition Link (MHL) 
						

							66
English ...
Appendices
TIP:
•  An image with higher or lower resolution than the projector’s native 
resolution (
1920 × 1080 ) will be displayed with scaling technology.
•  Sync on Green and Composite sync signals are not supported.
•  Signals other than those specified in the table above may not be displayed 
correctly. If this should happen, change the refresh rate or resolution on 
your PC. Refer to Display Properties help section of your PC for proce-
dures. 
						

							67... English
Appendices
Please note that damage resulting from 
incorrect installation 
will invalidate the 
warranty.
Ceiling Mount Installation
If you wish to use a third party ceiling mount kit, please 
ensure the screws used to attach a mount to the projector 
meet the following specifications:
 Screw type: M4*4
 Maximum screw length: 11mm
 Minimum screw length: 8mm
Warning: 1.  If you buy a ceiling mount from another 
company, please 
be sure to use the 
correct screw size. 
Screw size will vary 
depending on the 
thickness of the 
mounting plate.
2.  Be sure to keep at least 10 cm gap 
between the ceiling 
and the bottom of the 
projector.
3.  Avoid installing the projector near a heat 
source.
Warning: 
If you wish to have the 
projector installed on 
the ceiling:
-  
Do not attempt to install the projector 
yourself.
-  The projector must be installed by qualified 
technicians in order 
to ensure proper 
operation and reduce 
the risk of bodily 
injury.
-  In addition, the ceiling must be strong 
enough to support 
the projector and the 
installation must be in 
accordance with any 
local building codes.
-  Please consult your dealer for more 
information. 
Unit: mm
95
88
130
382
414
163
113151 
						

							68
English ...
Appendices
Warning: If you wish to have the 
projector installed on 
the wall:
-   Do not attempt to install the projector 
yourself.
-  The projector must be installed by qualified 
technicians in order 
to ensure proper 
operation and reduce 
the risk of bodily 
injury.
-  In addition, the wall must be strong 
enough to support 
the projector and the 
installation must be in 
accordance with any 
local building codes.
-  Please consult your dealer for more 
information. 
Please note that 
damage resulting from 
incorrect installation 
will invalidate the 
warranty.
Wall Mount Installation
To install NEC’s standard wall mount kits with attachment 
plate and fix by 4 screws.
Warning:   Avoid installing the projector near a heat 
source.
Unit: mm
88
130382
414
163
113151
To install Dukane’s standard wall mount kits with attachment 
						

							69... English
Appendices
Cabinet Dimensions
108
53
98
105
93
85 27 97382
382 292
44
44 307
414
267
254
Unit: mm
Lens center 
						

							70
English ...
Appendices
Pin Assignments of D-Sub COMPUTER Input 
Connector
Mini D-Sub 15 Pin Connector
1 2 3 4 5
11 12 13 14 15
6 7 8 9 10
Signal Level
Video signal : 0.7Vp-p (Analog)
Sync signal : TTL level
COMPUTER IN
NOTE: Pin Nos. 12 and 15 are required for DDC/CI.
Pin No.RGB Signal (Analog) YCbCr Signal
1 Red Cr
2 Green Y
3 Blue Cb
4 Ground
5 Ground
6 Red Ground Cr Ground
7 Green Gro Y Ground
8 Blue Ground Cb Ground
9 No Connection
10 Sync Signal Ground
11 No Connection
12 Bi-directional DATA (SDA)
13 Horizontal Sync or Composite 
Sync
14 Vertical Sync
15 Data Clock 
						

							71... English
Appendices
PC Control Codes and Cable Connection
PC Control Codes
Function Code Data
POWER ON 02H00H00H00H00H02H
POWER OFF 02H01H00H00H00H03H
INPUT SELECT COMPUTER 02H03H00H00H02H01H01H09H
INPUT SELECT HDMI 1 02H03H00H00H02H01HA1H A9H
INPUT SELECT HDMI 2 02H03H00H00H02H01HA2HAAH
INPUT SELECT VIDEO 02H03H00H00H02H01H06H0EH
PICTURE MUTE ON 02H10H00H00H00H12H
PICTURE MUTE OFF 02H11H00H 00H00H13H
SOUND MUTE ON 02H12H00H00H00H14H
SOUND MUTE OFF 02H13H00H00H00H15H
NOTE: Contact your local dealer for a full list of the PC Control Codes if needed.
Cable Connection
Communication Protocol Baud rate  ....................................................38400 bps
Data length  .................................................8 bits
Parity   ...........................................................No parity
Stop bit  ........................................................One bit
X on/off  ........................................................None
Communications procedure  ....................Full duplex
PC Control Connector (D-SUB 9P)
3 4 5
21
9876
NOTE 1: Pins 1, 4, 6 and 9 are no used.NOTE 2: Jumper “Request to Send” and “Clear to Send” together on both ends of the cable to simplify cable connection.
To TxD of PCTo RxD of PCTo GND of PC
To RTS of PCTo CTS of PC 
						

							Power
		
No	power	(POWER	indicator	does	not	light 	green).	 		
Power	cable's	plug	is	fully	inserted	into	the	wall	outlet.	 		
Lamp	cover	is	installed	correctly.	 		
Lamp	Hours	Used	(lamp	operation	hours)	was	cleared	after	lamp	replacement.	 		
No	power	even	though	you	press	and	hold	the	POWER	button	for	a	minimum	of	1	second.
		
Shut	down	during	operation.	 	 	
Power	cable's	plug	is	fully	inserted	into	the	wall	outlet.	 		
Lamp	cover	is	installed	correctly	.	 		
Power	Management	is	turned	off	(only	models	with	the	Power	Management	function).
Video and Audio
		
No	image	is	displayed	from	your	PC	or	video	equipment	to	the	projector.	 	 	
Still	no	image	even	though	you	connect	the	projector	to	the	PC	first,	then	start	the	PC.	 		
Enabling	your	notebook	PC's	signal	output	to	the	projector.	 	 			 A	combination	of	function	keys	will	enable/disable	the	external	display.	Usually,	the	combination	of	the"Fn"	key	along	with	one	of	the	12	function	keys	turns	the	external	display	on	or	off.	 		
No	image	(blue 	background).	 		
Still	no	image	even	though	you	press	the	AUTO	ADJUST	button.	 		
Still	no	image	even	though	you	carry	out	[RESET]	in	the	projector's	menu.	 		
Signal	cable's	plug	is	fully	inserted	into	the	input	connector	A	message	appears	on	the	screen.	 	 (	_____________________________________________	)	 		
The	source	connected	to	the	projector	is	active	and	available.	 		
Still	no	image	even	though	you	adjust	the	brightness	and/or	the	contrast.	 		
Input	source’s	 resolution	and	frequency	are	supported	by	the	projector.		
Image	is	too	dark.	 	 	
Remains	unchanged	even	though	you	adjust	the	brightness	and/or	the	contrast.		
Image	is	distorted.	 	 	
Image	appears 	to	be	trapezoidal	(unchanged	even	though	 		
you	carry	out	the	[KEYSTONE]	adjustment).
		
Parts	of	the	image	are	lost.	 	 	
Still	unchanged 	even	though	you	press	the	AUTO	ADJUST	button.	 		
Still	unchanged 	even	though	you	carry	out	[RESET]	in	the	projector's	menu.		
Image	is	shifted	in	the	vertical	or	horizontal 	direction.	 		
Horizontal	and	 vertical	positions	are	correctly	adjusted	on	a	computer	signal.	 		
Input	source's	resolution	and	frequency	are	supported	by	the	projector.	 		
Some	pixels	are	lost.		
Image	is	flickering.	 	 	
Still	unchanged 	even	though	you	press	the	AUTO	ADJUST	button.	 		
Still	unchanged 	even	though	you	carry	out	[RESET]	in	the	projector's	menu.	 		
Image	shows	flickering	or	color	drift	on	a	computer	signal.		
Image	appears	blurry	or	out	of	focus.	 	 	
Still	unchanged 	even	though	you	checked	the	signal's	reso-lution	on	PC	and	changed	it	to	projector's	native	resolution.	 		
The	throw	distance	is	within	22.2	to	30.6	cm	(8.7"	to	12.1"	).		 		
Still	unchanged 	even	though	you	adjusted	the	focus.		
No	sound.	 	 	
Audio	cable	is	correctly	connected	to	the	audio	input	of	the	projector.	 		
Still	unchanged 	even	though	you	adjusted	the	volume	level.
Other
		
Remote	control	does	not	work.	 	 	
No	obstacles	between	the	sensor	of	the	projector	and	the	remote	control.	 		
Projector	is	placed	near	a	fluorescent	light	that	can	disturb	the	infrared	remote	controls.	 		
Batteries	are	new	and	are	not	reversed	in	installation
		
Buttons	on	the	projector	cabinet	do	not	work.	 	 	
[CONTROL	PANEL	LOCK]	is	not	turned	on	in	the	menu.	 		
Still	unchanged 	even	though	you	press	and	hold	the	EXIT	button	for	minimum	of	10	seconds.
Troubleshooting Check List
Before contacting your dealer or service personnel, check the following list to be sure repairs are needed also by  
referring to the “Troubleshooting” section in your user’s manual. This checklist below will help us solve your   
problem more efficiently.
* Print the following pages.
Frequency of occurrence		always				sometimes	(How	often?_______________________)					other	(__________________) 
						

							In the space below please describe your problem in detail.
Information on application and environment where your projector is usedProjector
Model	number:
Serial	No.:
Date	of	purchase:
Lamp	operating	time	(hours):
Eco	Mode:		Off			Eco
Information	on	input	signal:
Horizontal	synch	frequency	 [	 ]	kHz
Vertical	synch	frequency	 [	]	Hz
Synch	polarity	H			(+)			(-)
	V			(+)			(-)
Synch	type		Separate			Composite
		Sync	on	Green
STATUS	Indicator:
Steady	light		Red
Flashing	light	[	]	cycles
Remote	control	model	number:
Installation environment
Screen	size:		 inch
Screen	type:		White	matte			Beads			Polarization
			Wide	angle			High	contrast
Throw	distance:	 feet/inch/m
Orientation:		Ceiling	mount			Desktop
Power	outlet	connection:
		Connected	directly	 to	wall	outlet
		Connected	to	power	cord	extender	or	other	(the	number	of	connected	equipment______________)
		Connected	to	a	power	cord	reel	or	other	(the	number	of	connected	equipment______________)
Computer
Manufacturer:
Model	number:
Notebook	PC		/	Desktop		
Native	resolution:
Refresh	rate:
Video	adapter:
Other:
Video equipment
VCR,	DVD	player,	Video	camera,	Video	game	or	other
Manufacturer:
Model	number:
Signal cable
	standard	or	other	manufacturer's	cable?
Model	number:		 Length:		 inch/m
Distribution	amplifier
Model	number:
Switcher
Model	number:
Adapter
Model	number:
Projector
PC
DVD Player
Dukane