Dukane Projector 6860WSS-B User Manual

							28
❺ Magnifying a Picture
You	can	magnify	the	picture	up	to	four	times.
NOTE: 
•	 Depending	on	an	input	signal,	the	maximum	magnification	may	be	less	than	four	times,	or	the	function	may	be	restricted.
To	do	so:
1.	 Press	the	D-ZOOM	(+)	button	to	magnify	the	picture.
2. Press the ▲▼◀▶ button.
	 The	area	of	the	magnified	image	will	be	moved
3. Press the D-ZOOM (−) button.
	 Each	time	the	D-ZOOM	(−)	button	is	pressed,	the	image	is	demagni-
fied.
NOTE: 
•	 The	image	will	be	magnified	or	demagnified	at	the	center	of	the	screen.
•	 Displaying	the	menu	will	cancel	the	current	magnification.
3. Convenient Features  
						

							29
❻ Changing LIGHT MODE/Checking Energy-Saving Effect 
Using LIGHT MODE [LIGHT MODE]
When	either	[ECO1]	or	[ECO2]	in	[LIGHT	MODE]	is	selected,	motion	noise	of	the	projector	is	cut	down	by	lowering	
brightness	of	its	light	source.	By	saving	energy	consumption,	the	CO2	emission	from	this	projector	can	be	reduced.
LIGHT	MODEIcon	at	the	bottom	
of	the	menuDescription
NORMAL
100%	brightness
The	screen	will	be	brightly	lit.
ECO1Brightness	will	be	at	about	80%.
The	cooling	fan	will	also	slow	down	accordingly.
Lower	power	consumption
ECO2Brightness	will	be	at	about	50%.
The	cooling	fan	will	also	slow	down	accordingly.
Lower	power	consumption	considerably
*	 When	the	brightness	is	lowered,	the	cooling	fan	speed	will	be	reduced	accordingly.
To	turn	on	the	[LIGHT	MODE],	do	the	following:	
1. Press LIGHT button on the cabinet.
•	 In	another	way,	press	ECO/L-SHIFT	button	on	the	remote	control.
	 The	[LIGHT	MODE]	screen	will	be	displayed.
 
2. Press the ENTER button.
	 The	[LIGHT	MODE]	selection	screen	will	be	displayed.
3. Use the ▼▲ buttons to make a selection, and press the ENTER 
button.
	 The	display	will	return	to	the	[LIGHT	MODE]	screen	and	the	selected	
option	will	be	applied.
	 Press	the	MENU	button	to	return	to	the	original	screen.
3. Convenient Features  
						

							30
NOTE: 
•	 The	[LIGHT	MODE]	can	be	changed	by	using	the	menu.
	 Select	[SETUP]	→	[INSTALLATION]	→	[LIGHT	MODE]	→	[LIGHT	MODE].
•	 The	light	module	hours	used	can	be	checked	in	[USAGE	TIME].	Select	[INFO.]	→	[USAGE	TIME].
•	 After	a	lapse	of	1	minute	from	when	the	projector	displays	a	blue,	black	or	logo	screen,	[LIGHT	MODE]	will	automatically	switch	
to	[ECO].	
•	 If	the	projector	is	overheated	in	[NORMAL]	mode,	there	may	be	a	case	where	the	[LIGHT	MODE]	automatically	changes	to	[ON]	
mode	to	protect	the	projector.	This	is	called	“Forced	LIGHT	MODE”.	When	the	projector	is	in	the	Forced	LIGHT	MODE,	the	picture	
brightness	decreases	slightly	and	the	TEMP.	indicator	lights	orange.	At	the	same	time	the	Thermometer	symbol	[		]	is	displayed	
at the bottom right of the screen.
	 When	the	projector	comes	back	to	normal	temperature,	the	Forced	LIGHT	MODE	is	cancelled	and	the	[LIGHT	MODE]	returns	to	
[NORMAL]	mode.
3. Convenient Features  
						

							31
Checking Energy-Saving Effect [CARBON METER]
This	feature	will	show	energy-saving	effect	in	terms	of	CO2	emission	reduction	(kg)	when	the	projector’s	[LIGHT	MODE]	
is	set	to	either	[ECO1]	or	[ECO2].	This	feature	is	called	as	[CARBON	METER].
There	are	two	messages:	[TOTAL	CARBON	SAVINGS]	and	[CARBON	SAVINGS-SESSION].	The	[TOTAL	CARBON	
SAVINGS]	message	shows	the	total	amount	of	CO2	emission	reduction	from	the	time	of	shipment	up	to	now.	You	can	
check	the	information	on	[USAGE	TIME]	from	[INFO.]	of	the	menu.	(→	page	117)
The	[CARBON	SAVINGS-SESSION]	message	shows	the	amount	of	CO2	emission	reduction	between	the	time	of	
changing	to	LIGHT	MODE	immediately	after	the	time	of	power-on	and	the	time	of	power-off.	The	[CARBON	SAVINGS-
SESSION]	message	will	be	displayed	in	the	[POWER	OFF/	ARE	YOU	SURE	?]	message	at	the	time	of	power-off.
TIP:
•	 The	formula	shown	below	is	used	to	calculate	the	amount	of	CO2	emission	reduction.	Amount	of	CO2	emission	reduction	=	(Power	
consumption	in	[NORMAL]	LIGHT	MODE	–	Power	consumption	in	current	setting)	×	CO2	conversion	factor.*	When	an	energy-
saving	LIGHT	MODE	is	selected,	or	the	Lens	Shutter	is	used,	there	will	be	a	further	reduction	in	CO2 emission.
*	 Calculation	for	amount	of	CO2	emission	reduction	is	based	on	an	OECD	publication	“CO2	Emissions	from	Fuel	Combustion,	
2008	Edition”.
•	 The	[TOTAL	CARBON	SAVINGS]	is	calculated	based	on	savings	recorded	in	15	minutes	intervals.
•	 This	formula	will	not	apply	to	the	power	consumption	which	is	not	affected	by	whether	[LIGHT	MODE]	is	turned	on	or	off.
3. Convenient Features  
						

							32
❼ Correcting Horizontal and Vertical Keystone Distortion 
[CORNERSTONE]
Use	the	[CORNERSTONE]	feature	to	correct	keystone	(trapezoidal)	distortion	to	make	the	top	or	bottom	and	the	left	
or	right	side	of	the	screen	longer	or	shorter	so	that	the	projected	image	is	rectangular.
1.	 Press	and	hold	the	3D	REFORM	button	for	2	seconds	at	least	to	reset	current	adjustments.
	 Current	adjustments	for	[GEOMETRIC	CORRECTION]	will	be	cleared.
2.	 Project	an	image	so	that	the	screen	is	smaller	than	the	area	of	the	raster.
Projected	image
The
	drawing	shows	the	upper	right	corner.
3.	 Pick	up	any	one	of	the	corners	and	align	the	corner	of	the	image	with	a	corner	of	the	screen.
4. Press the 3D REFORM button.
	 Display	the	[GEOMETRIC	CORRECTION]	screen	of	the	on-screen	menu.
3. Convenient Features  
						

							33
5. Press the ▼	button	to	align	with	the	[CORNERSTONE]	and	then	press	the	ENTER	button.
The	drawing	shows	the	upper	left	icon	(	)	is	selected.
	 The	screen	will	switch	to	the	[CORNERSTONE]	screen.
NOTE:
•	 When	a	[GEOMETRIC	CORRECTION]	function	other	than	[CORNERSTONE]	has	been	set	up,	the	[CORNERSTONE]	screen	
will	not	be	displayed.	When	the	screen	is	not	displayed,	either	press	the	3D	REFORM	button	for	2	or	more	seconds,	or	run	
[RESET]	in[GEOMETRIC	CORRECTION]	to	clear	the	adjustment	value	of	[GEOMETRIC	CORRECTION].
6. Use the ▲▼◀▶ button to select one icon (▲) which points in the direction you wish to move the projected 
image	frame.
7. Press the ENTER button.
8. Use the ▲▼◀▶	button	to	move	the	projected	image	frame	as	shown	on	the	example.
9.	 Press	the	ENTER	button.
10. Use  the ▲▼◀▶ button to select another icon which points in the direction.
11.	Repeat	steps	from	7	to	10	to	complete	the	cornerstone	adjustment.
12.	On	the	[CORNERSTONE]	screen,	select	[EXIT]	or	press	the	EXIT	button	on	the	remote	control.
	 The	confirmation	screen	is	displayed.
3. Convenient Features  
						

							34
13. Press  the ◀ or ▶	button	to	highlight	the	[OK]	and	press	the	ENTER	button.
	 This	completes	the	[CORNERSTONE]	correction.
•	 Returning	to	the	[CORNERSTONE]	screen,	select	[CANCEL]	and	press	the	ENTER	button.
NOTE: 
•	 Even	when	the	projector	is	turned	on,	the	last	used	correction	values	are	applied.
•	 Carry	out	either	one	of	the	following	actions	to	clear	the	adjustment	value	of	[CORNERSTONE].
•	 In	Step	12,	select	[RESET]	and	then	press	the	ENTER	button.
•	 Press	the	3D	REFORM	button	for	2	or	more	seconds.
•	 Run	[DISPLAY]	→	[GEOMETRIC	CORRECTION]	→	[RESET]	in	the	on-screen	menu.
•	 Using	CORNERSTONE	correction	can	cause	the	image	to	be	slightly	blurred	because	the	correction	is	made	electronically.
3. Convenient Features  
						

							35
❽ Preventing the Unauthorized Use of the Projector [SECURITY]
A	keyword	can	be	set	for	your	projector	using	the	Menu	to	avoid	operation	by	an	unauthorized	user.	When	a	keyword	
is	set,	turning	on	the	projector	will	display	the	Keyword	input	screen.	Unless	the	correct	keyword	is	entered,	the	pro-
jector	cannot	project	an	image.	
•	The	[SECURITY]	setting	cannot	be	cancelled	by	using	the	[RESET]	of	the	menu.
To	enable	the	Security	function:
1. Press the MENU button.
	 The	menu	will	be	displayed.
2. Press the ▶	button	twice	to	select	[SETUP]	and	press	the	▼	button	or	the	ENTER	button	to	select	[MENU].
3. Press the ▶	button	to	select	[CONTROL].
4. Press the ▼	button	three	times	to	select	[SECURITY]	and	press	the	ENTER	button.
	 The	OFF/ON	menu	will	be	displayed.
5. Press the ▼	button	to	select	[ON]	and	press	the	ENTER	button.
	 The	[SECURITY	KEYWORD]	screen	will	be	displayed.
6.	 Type	in	a	combination	of	the	four	▲▼◀▶ buttons and press the ENTER button.
NOTE:	A	keyword	must	be	4	to	10	digits	in	length.
	 The	[CONFIRM	KEYWORD]	screen	will	be	displayed.
NOTE:	Make	a	note	of	your	password	and	store	it	in	a	safe	place.
3. Convenient Features  
						

							36
7.	 Type	in	the	same	combination	of	▲▼◀▶ buttons and press the ENTER button.
	 The	confirmation	screen	will	be	displayed.
8.	 Select	[YES]	and	press	the	ENTER	button.
	 The	SECURITY	function	has	been	enabled.
To	turn	on	the	projector	when	[SECURITY]	is	enabled:
1. Press the  button.
•	 If	using	the	remote	control,	press	the	POWER	ON	button.
	 The	projector	will	be	turned	on	and	display	a	message	to	the	effect	
that	the	projector	is	locked.
 
2. Press the MENU button.
3. Type in the correct keyword and press the ENTER button. The projector will display an image.
NOTE: The security disable mode is maintained until the main power is tu\
rned off or unplugging the power cord.
3. Convenient Features  
						

							37
To	disable	the	SECURITY	function:
1. Press the MENU button.
	 The	menu	will	be	displayed.
2.	 Select	[SETUP]	→	[CONTROL]	→	[SECURITY]	and	press	the	ENTER	button.
	 The	OFF/ON	menu	will	be	displayed.
3.	 Select	[OFF]	and	press	the	ENTER	button.
	 The	SECURITY	KEYWORD	screen	will	be	displayed.
4. Type in your keyword and press the ENTER button.
	 When	the	correct	keyword	is	entered,	the	SECURITY	function	will	be	disabled.
NOTE:	If	you	forget	your	keyword,	contact	your	dealer.	Your	dealer	will	provide	you	with	your	keyword	in	exchange	for	your	request	
code.	Your	request	code	is	displayed	in	the	Keyword	Confirmation	screen.	In	this	example	[NB52-YGK8-2VD6-K585-JNE6-EYA8]	
is a request code.
3. Convenient Features