Dukane Projector 6860WSS User Manual

							88
CORNERSTONE
Display	the	4-point	correction	screen	and	adjust	the	trapezoidal	distortion	of	the	projection	screen.
Please	refer	to	“Correcting	Horizontal	and	Vertical	Keystone	Distortion	[CORNERSTONE]”	(→	page	32)	for	details	
on	the	operation.
HORIZONTAL	CORNER/VERTICAL	CORNER
Distortion	correction	for	corner	projection	such	as	wall	surfaces.
HORIZONTAL CORNER
 ������������������������������Performs correction for projection onto a wall lying at an angle to the hor\
izontal direction�
* Reverse angle correction is also possible�
VERTICAL CORNER
 ������������������������������Performs correction for projection onto a wall lying at an angle to the ver\
tical direction�
* Reverse angle correction is also possible�
NOTE:
•	 When	the	maximum	adjustment	range	is	exceeded,	distortion	adjustment	is	disabled.	Set	up	the	projector	at	an	optimal	angle	as	
the deterioration in the image quality increases as the distortion adjus\
tment volume gets larger.
•	 Please	note	that	the	image	will	go	out	of	focus	due	to	the	difference	in	the	distance	between	the	upper	and	lower	or	left	and	right	
sides	and	the	center	of	the	screen	for	projections	cutting	across	corners.	Lenses	with	short	focal	points	are	also	not	recommended	
for projections cutting across corners as the image will go out of focus\
.
5. Using On-Screen Menu  
						

							89
Adjustment method
1.	 Align	the	cursor	with	the	[HORIZONTAL	CORNER]	or	[VERTICAL	CORNER]	of	the	[GEOMETRIC	CORREC-
TION]	menu	and	then	press	the	ENTER	button.
•	 The	adjustment	screen	will	be	displayed.
2. Press the ▼▲◀▶ buttons to align the cursor (yellow box) with the target adjustment point and then press 
the ENTER button.
•	 The	cursor	will	change	into	an	adjustment	point	(yellow	in	color).
3. Press the ▼▲◀▶	buttons	to	adjust	the	corners	or	sides	of	the	screen	and	then	press	the	ENTER	button.
•	 The	adjustment	point	will	go	back	to	being	a	cursor	(yellow	box).
Explanation	of	screen	transition	
•	 The	adjustment	points	of	the	four	corners	(a,	c,	f	and	h	in	the	drawing)	will	move	independently.
•	 The	following	adjustment	points	differ	at	the	[HORIZONTAL	CORNER]	and	[VERTICAL	CORNER].
	 HORIZONTAL	CORNER:	When	Point	b	in	the	drawing	is	moved,	and	the	upper	side	and	Point	g	are	moved,	the	
lower	side	will	move	in	a	parallel	manner.
	 VERTICAL	CORNER:	When	Point	d	in	the	drawing	is	moved,	and	the	left	side	and	Point	e	are	moved,	the	right	
side	will	move	in	a	parallel	manner.
	 [Adjustment	points	of	the	[HORIZONTAL	CORNER]	screen	and	movement	points	of	the	projection	screen]
a
bbc
de
fgh
a c
d e
f
gh
Point	b	will	be	displaced	in	a	parallel	manner	at	the	same	time	as	Points	a,	b,	c
Point
	g	will	be	displaced	in	a	parallel	manner	at	the	same	time	as	Points	f,	g,	h
	 [Adjustment	points	of	the	[VERTICAL	CORNER]	screen	and	movement	points	of	the	projection	screen]
a a b
b c
c
d d e
e
f f
g
gh
h
Point	d	will	be	displaced	in	a	parallel	manner	at	the	same	time	as	Points	a,	d,	f
Point
	e	will	be	displaced	in	a	parallel	manner	at	the	same	time	as	Points	f,	g,	h
4.	 Start	from	Step	2	onwards	to	adjust	the	other	points.
5. When the adjustment is completed, press the ▼▲◀▶	buttons	to	align	the	cursor	with	the	[EXIT]	in	the	
adjustment screen and then press theENTER button.
•	 Switch	to	the	[GEOMETRIC	CORRECTION]	menu	screen.
5. Using On-Screen Menu  
						

							90
PINCUSHION
Adjust	the	curve	distortion	of	the	projection	screen.
TOP ������������������������Adjust the curve distortion of the upper edge of the projection 
screen�
BOTTOM ����������������Adjust the curve distortion of the lower edge of the projection 
screen�
LEFT ����������������������Adjust the curve distortion of the left edge of the projection screen�
RIGHT ��������������������Adjust the curve distortion of the right edge of the projection 
screen�
TOP
LEFT RIGHT
BOTTOM
PC	TOOL	(For	future	support)
Recall	the	geometric	correction	data	that	is	registered	in	the	projector	beforehand.
There	are	three	types	of	registered	data.
NOTE:
•	 KEYSTONE,	CORNERSTONE,	and	PINCUSHION	cannot	be	selected	when	setting	the	geometric	correction	using	a	PC	tool.
•	 To	clear	the	[GEOMETRIC	CORRECTION]	data	that	has	been	set	up,	press	the	3D	REFORM	button	for	2	or	more	seconds.
•	 As	electrical	correction	is	carried	out	in	geometric	correction,	the	brightness	may	be	affected	and	the	picture	quality	may	be	
degraded.
RESET
Reset	the	adjustment	value	that	has	been	set	up	in	GEOMETRIC	CORRECTION	(return	to	the	initial	value).
5� Using On-Screen Menu  
						

							91
[EDGE BLENDING]
This	adjusts	the	edges	(boundaries)	of	the	projection	screen	when	projecting	high	resolution	videos	using	a	combina-
tion	of	several	projectors	in	the	up,	down,	left	and	right	positions.
MODE
This	enables	or	disables	the	EDGE	BLENDING	function.
When	MODE	is	set	to	ON,	the	TOP,	BOTTOM,	LEFT,	RIGHT	and	BLACK	LEVEL	settings	can	be	adjusted.
TOP/BOTTOM/LEFT/RIGHT
This	selects	the	EDGE	BLENDING	locations	on	the	left,	right,	top	and	bottom	on	the	screen.
The	following	settings	can	be	adjusted	when	an	item	is	selected.	(→	page	57)
CONTROL
 ��������������Enable TOP, BOTTOM, LEFT and RIGHT functions�
MARKER ����������������Set whether to display marker or not when adjusting the range and display position� When turned on, a 
magenta marker for adjusting the range adjustment and a green marker for adjusting the display position 
will be displayed�
RANGE �������������������Adjust the range (width) of the edge blending�
POSITION ��������������Adjust the display position of the edge blending�
BLACK	LEVEL
Divide	the	screen	into	nine	parts	and	keep	the	black	level	uniform	for	each	projector.
The	nine	divisions	screens	are	TOP-LEFT,	TOP-CENTER,	TOP-RIGHT,	CENTER-LEFT,	CENTER,	CENTER-RIGHT,	
BOTTOM-LEFT,	BOTTOM-CENTER	and	BOTTOM-RIGHT.	(→	page	60)
5. Using On-Screen Menu  
						

							92
[MULTI SCREEN]
WHITE	BALANCE
This	adjusts	the	white	balance	for	each	projector	when	projecting	using	a	combination	of	several	projectors.
This	can	be	adjusted	when	[MODE]	is	set	to	[ON].
BRIGHTNESS W, BRIGHTNESS R, BRIGHTNESS G, BRIGHTNESS B
 ������������������������������Adjusting the black color of the video�
CONTRAST W, CONTRAST R, CONTRAST G, CONTRAST B
 ������������������������������Adjusting the white color of the video�
PICTURE	SETTING
This	sets	the	division	condition	when	projecting	using	a	combination	of	several	projectors.
Please	refer	to	“4.	Multi-Screen	Projection”	(→	page	48)	for	details.
MODEOFFUse	the	projector	in	a	standalone	state.
ZOOMThis	adjusts	the	position	and	width	of	the	video	area	that	you	wish	to	divide.	The	edge	blending	width	will	also	be	automatically	set	to	that	width.
TILINGThis	assigns	the	divided	screens	to	the	projectors.	The	edge	blending	function	will	also	be	set	automatically.
ZOOMHORIZONTAL	ZOOMThis	maginifies	the	video	area	in	the	horizontal	direction.
VERTICAL	ZOOMThis	maginifies	the	video	area	in	the	vertical	direction.
HORIZONTAL	POSITIONThis	shifts	the	video	area	in	the	horizontal	direction.
VERTICAL	PO-
SITIONThis	shifts	the	video	area	in	the	vertical	direction.
TILING WIDTHThis	selects	the	number	of	projectors	to	be	arranged	horizontally.
HEIGHTThis	selects	the	number	of	projectors	to	be	arranged	vertically.
HORIZONTAL	POSITIONThis	selects	the	position	of	the	projector	starting	from	the	left	among	those	arranged	horizontally.
VERTICAL	PO-
SITIONThis	selects	the	position	of	the	projector	starting	from	the	top	among	those	arranged	vertically.
5. Using On-Screen Menu  
						

							93
Conditions for using tiling
•	 All	the	projectors	need	to	fulfil	the	following	conditions.
•	 The	panel	size	must	be	the	same
•	 The	projection	screen	size	must	be	the	same
•	 The	left	and	right	ends	or	top	and	bottom	ends	of	the	projection	screen	must	be	consistent.
•	 The	settings	for	the	left	and	right	edges	of	the	edge	blending	are	the	same
•	 The	settings	for	the	top	and	bottom	edges	of	the	edge	blending	are	the	same
	 If	the	tiling	conditions	are	satisfied,	the	video	screen	of	the	projector	at	each	installation	position	will	be	automatically	
extracted	and	projected.
	 If	the	tiling	conditions	are	not	satisfied,	adjust	the	video	screen	of	the	projector	at	each	installation	position	using	
the	zoom	function.
•	 Assign	a	unique	control	ID	to	each	projector.
•	 Set	the	“Color	Setting”	and	“DeepColor	Setting”	on	your	Blu-ray	player	or	computer	to	“Auto”.	Refer	to	the	owner’s	
manual	accompanying	your	Blu-ray	player	or	computer	for	more	information.
	 Connect	the	HDMI	output	of	your	Blu-ray	player	or	computer	to	the	first	projector.	Then	connect	to	the	HDMI	IN	input	
terminal	of	the	second	and	subsequent	tiled	projectors.
Tiling	setting	example)	Number	of	horizontal	units	=	2,	Number	of	vertical	units	=	2
Horizontal	order	=	Second	unit
Vertical	order	=	First	unit
5. Using On-Screen Menu  
						

							94
❼ Menu Descriptions & Functions [SETUP]
[MENU]
Selecting	Menu	Language	[LANGUAGE]	
You	can	choose	one	of	29	languages	for	on-screen	instructions.
NOTE:	Your	setting	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu.
Selecting	Menu	Color	[COLOR	SELECT]
You	can	choose	between	two	options	for	menu	color:	COLOR	and	MONOCHROME.
Turning	On	/	Off	Source	Display	[INPUT	DISPLAY]
This	option	turns	on	or	off	input	name	display	such	as	HDMI,	DisplayPort,	BNC,	BNC(CV),	BNC(Y/C),	COMPUTER,	
HDBaseT	to	be	displayed	on	the	top	right	of	the	screen.
Turning	messages	on	and	off	[MESSAGE	DISPLAY]
This	option	selects	whether	or	not	to	display	projector	messages	at	the	bottom	of	the	projected	image.
Even	when	“OFF”	is	selected,	the	security	lock	warning	is	displayed.	The	security	lock	warning	turns	off	when	the	
security	lock	is	canceled.
Turning	ON/OFF	Control	ID	[ID	DISPLAY]
ID DISPLAY �����������This option turns on or off the ID number which is displayed when the ID SET button on the remote control 
is pressed� (→ page 105)
5. Using On-Screen Menu  
						

							95
[3D	CAUTION	MESSAGE]
This	selects	whether	to	display	a	caution	message	or	not	when	switching	to	a	3D	video.
The	default	condition	when	shipped	from	the	factory	is	ON.
OFF ������������������������The 3D caution message screen will not be displayed�
ON �������������������������The 3D caution message screen will be displayed when switching to a 3D v\
ideo� Press the ENTER button 
to cancel the message�
•	 The	message	will	disappear	automatically	after	60	seconds	or	when	other	buttons	are	pressed.	If	it	disap-
pears automatically, the 3D caution message will be displayed again when switching to a 3D \
video�
Selecting	Menu	Display	Time	[DISPLAY	TIME]
This	option	allows	you	to	select	how	long	the	projector	waits	after	the	last	touch	of	a	button	to	turn	off	the	menu.	The	
preset	choices	are	[MANUAL],	[AUTO	5	SEC],	[AUTO	15	SEC],	and	[AUTO	45	SEC].	The	[AUTO	45	SEC]	is	the	fac-
tory	preset.
5� Using On-Screen Menu  
						

							96
[INSTALLATION]
Selecting	Projector	Orientation	[ORIENTATION]
This	reorients	your	image	for	your	type	of	projection.	The	options	are:	desktop	front	projection,	ceiling	rear	projection,	
desktop	rear	projection,	and	ceiling	front	projection.
NOTE: 
•	 Please	consult	the	dealer	if	you	require	special	installation	services	e.g.	when	mounting	the	projector	to	a	ceiling.	Never	install	
the projector on your own. This may result in the projector falling down\
 and causing injury to people.AUTO
 ���������������������This automatically detects and projects the DESKTOP FRONT and CEILING FR\
ONT�
NOTE:
•	 The	DESKTOP	REAR	and	CEILING	REAR	will	not	be	detected.	Please	select	manually.
DESKTOP	FRONTCEILING	REAR
DESKTOP	REARCEILING	FRONT
TIP:
•	 Check	whether	the	automatic	DESKTOP	FRONT	is	installed	within	±	10	degrees	for	floor	installation	and	whether	the	CEILING	
FRONT	is	within	±10	degrees	for	ceiling	installation.	Select	manually	when	the	projection	screen	is	inverted.
5. Using On-Screen Menu  
						

							97
Selecting	Aspect	Ratio	and	Position	for	Screen	[SCREEN	TYPE]
Screen	typeSets	the	aspect	ratio	of	the	projection	screen.
FREEThe	ratio	of	the	liquid	crystal	panel	is	selected.	Select	this	when	projecting	
multi-screen	and	17:9	screen	(2K).
4:3	screenFor	a	screen	with	a	4:3	aspect	ratio
16:9	screenFor	a	screen	with	a	16:9	aspect	ratio
16:10	screenFor	a	screen	with	a	16:10	aspect	ratio
NOTE:
•	
After	changing	the	screen	type,	check	the	setting	of	[ASPECT	RATIO]	in	the	menu.	(→ page 80)
Using	the	Wall	Color	Correction	[WALL	COLOR]
This	function	allows	for	quick	adaptive	color	correction	in	applications	where	the	screen	material	is	not	white.
Selecting	Fan	Mode	[FAN	MODE]
Fan	Mode	is	used	to	set	the	speed	of	the	internal	cooling	fan.
MODE ��������������������Select three modes for fan speed: AUTO and HIGH�
AUTO: The built-in fans automatically run at a variable speed according \
to the internal temperature�
HIGH: The built-in fans run at a high speed� Select this option when using the projector at altitudes ap-
proximately 2500 feet/760 meters or higher� 
NOTE: 
•	 Make	sure	the	speed	is	set	to	[HIGH]	when	you	are	using	this	device	continuously	for	several	days.
•	 Set	[FAN	MODE]	to	[HIGH]	when	using	the	projector	at	altitudes	approximately	2500	feet/760	meters	or	higher.
•	 Using	the	projector	at	altitudes	approximately	2500	feet/760	meters	or	higher	without	setting	to	[HIGH]	can	cause	the	projector	
to	overheat	and	the	protector	could	shut	down.	If	this	happens,	wait	a	couple	minutes	and	turn	on	the	projector.
•	 Using	the	projector	at	altitudes	approximately	2500	feet/760	meters	or	higher	can	shorten	the	life	of	optical	components	such	as	
the light module.
•	 Your	setting	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu.
TIP:	
•	 When	[HIGH]	is	selected	for	[FAN	MODE],	a	symbol	icon	 will be displayed at the bottom of the menu.
5. Using On-Screen Menu