Dukane Projector 8934A User Manual

							61
OPTION menu
ItemDescription
SCHEDULE
(Continued ) 2/2 page (Set specific date from 1 to 10.)
Press the ▼ cursor button to move from 1/2 page to 2/2 page with
the state of selecting "SATURDAY".
■ PROGRAM EDIT
The TIME and EVENT for Program 1 to 16 can be editted.
• RETURN
Select this to go back 
to the top menu of the 
SCHEDULE.
• SELECT
Select from PROGRAM-01 
to 16 to edit. 
Each PROGRAM can be 
setup up to 20 settings
• COPY TO
The selected program (with the settings of TIME and EVENT) 
can be copied to other program.
• APPLY
Select this to apply and save all adjustments and settings.
(continued on next page)
Check  mark 
in the boxDate and first setup 
info could be seen 
with the check mark. 
						

							62
OPTION menu
ItemDescription
SCHEDULE
(Continued )
■ How to edit the selected PROGRAM
1. 
 Select from 1 to 20 events.  
Use the ▲/▼ cursor buttons to select.  
Press ► cursor button to set the TIME and EVENT.
2. Use the ◄/► cursor 
buttons to select.
3. Use the ◄/► cursor 
buttons to adjust.
EVENT can be selected as listed below. ◦ POWER − ON, ST

ANDBY
◦ INPUT SOURCE − "input source"channel
◦ 
ECO MODE −  OFF, ECO-1, ECO-2, INTELLIGENT ECO, 
SAVER
◦ BLANK − ON, OFF
4. Press ► cursor button to finish the settings. 
5. 
 Select APPLY to save the settings.
NOTE
(continued on next page)                 •
 Please refer to the actual on-screen display(OSD)  
for appropriate operation. 
						

							63
OPTION menu
ItemDescription
SERVICE Selecting this item displays the SERVICE 
menu.
Select an item using the ▲/▼ buttons, 
and press the ► button or the ENTER 
button on the remote control to execute 
the item.
ALTITUDE
Using the ▲/▼ buttons switches the rotation speed of the cooling fans. 
The HIGH is the mode for use at highlands etc. If the projector is used
at an altitude of about 1600 m (5250 feet) or higher, select HIGH. 
Otherwise, select NORMAL. Note that the projector is noisier when the 
HIGH is selected.
HIGH 
ó NORMAL
AUTO ADJUST
Using the ▲/▼ buttons to select one of the mode. When the 
DISABLE is selected, the automatic adjustment feature is disabled.
FINE  ó FAST 
ó DISABLE
   
FINE: Finer tuning including H.SIZE adjustment.
FAST:  Faster tuning, setting H.SIZE to prearranged data for the 
input signal.
• 
Depending on conditions, such as input image, signal cable to the 
projector, environment around the projector, etc., the automatic adjustment 
may not work correctly.  In such a case, please choose DISABLE to 
disable the automatic adjustment, and make adjustment manually.
GHOST
Adjust the settings using the ▲/▼ buttons to eliminate ghosting.
KEY LOCK
(1)
  Use the ▲/▼ buttons to choose the operations control.
CONTROL PANEL  ó REMOTE CONTROL
(2)
  Use the ◄/► buttons to select ON or OFF.
ON  ó OFF
Selecting ON in Step 2 locks the buttons except  STANDBY/ON on 
the operations control selected in Step 1. Selecting OFF releases 
the locked buttons on the operations control selected in Step 1.
• Please use this function to prevent tampering or accidental 
operation. 
(continued on next page) 
						

							64
OPTION menu
ItemDescription
SERVICE
(continued) REMOTE FREQ.
(1)
  Use the ▲/▼ button to change the projector's remote sensor 
frequency setting 
(
18).
1:NORMAL  ó 2:HIGH
(2)
  Use the ◄/► button to change the 
projector's remote sensor on or off. ON  ó OFF
If the remote control does not function correctly, disable either of them.It's not possible to disable both options at the same time.
COMMUNICATION
Selecting this item displays COMMUNICATION 
menu. 
In this menu, you can configure the serial 
communication settings of the projector using the 
CONTROL port.
• Select an item using the cursor buttons ▲/▼. 
Then pressing the ► button opens the submenu 
for the setting item you selected. Or, pressing 
the ◄ button instead of the ► button makes the 
menu back to the previous one without changing 
the setup. Each submenu can be operated as 
described above.
• When COMMUNICATION TYPE (
 65) is set to 
OFF, the other items in COMMUNICATION menu 
are invalid. 
• For the function of serial communication, refer to  
the Network Guide.
(continued on next page) 
						

							65
OPTION menu
ItemDescription
SERVICE
(continued)
COMMUNICATION(continued)
COMMUNICATION TYPE
Select the communication type for transmission via 
the CONTROL port.
NETWORK BRIDGE: Select this type, if it is  required to control an external device as a 
network terminal, via this projector from the 
computer.
The CONTROL port doesn't accept RS-232C  
commands (Network Bridge Function  in the 
Network Guide)
OFF: Select this mode to receive RS-232C  commands using the  CONTROL port. 
• OFF is selected as the default setting. 
• When you select the NETWORK BRIDGE, check 
the item, TRANSMISSION METHOD  (
below
)
SERIAL SETTINGS
Select the serial communication condition for the 
CONTROL port. BAUD RATE 4800bps  ó 9600bps 
ó 19200bps 
ó 38400bps
      
 PARITY
NONE  ó ODD 
ó EVEN
    
• The BAUD RATE is fixed to 19200bps 
and PARITY is fixed NONE when the 
COMMUNICATION TYPE is set to OFF  (
above
).
TRANSMISSION METHOD
Select the transmission method for communication 
by the NETWORK BRIDGE from the  CONTROL 
port.
HALF-DUPLEX  ó FULL-DUPLEX
HALF-DUPLEX: This method lets the projector  make two way communication, but only one 
direction, either transmitting or receiving data, is 
allowed at a time.
FULL-DUPLEX: This method lets the projector  make two way communication, transmitting and 
receiving data at the same time.
• HALF-DUPLEX is selected as the default setting.
• If you select HALF-DUPLEX, check the setting of 
the item RESPONSE LIMIT TIME (
 66).
(continued on next page) 
						

							66
OPTION menu
ItemDescription
SERVICE
(continued)
COMMUNICATION (continued)
RESPONSE LIMIT TIME
Select the time period to wait for receiving 
response data from other device communicating by 
the NETWORK BRIDGE and the HALF-DUPLEX 
through the CONTROL port.
OFF  ó 1s 
ó 2s 
ó 3s
    
OFF: Select this mode if it is not required to check  the responses from the device that the projector 
sends data to. In this mode, the projector can 
send out data from the computer continuously.
1s /2s /3s: Select the time period to keep the  projector waiting for response from the device 
that the projector sends data to. While waiting the 
response, the projector does not send out any 
data from the CONTROL port.
• This menu is available only when the NETWORK 
BRIDGE is selected for the COMMUNICATION 
TYPE and the HALF-DUPLEX is selected for the 
TRANSMISSION METHOD  (
65).
• OFF is selected as the default setting.
(continued on next page) 
						

							67
OPTION menu
ItemDescription
SERVICE
(continued) INFORMATION
Selecting this item displays a dialog titled “INPUT_INFORMATION”. 
It shows the information about the current input.
• The “FRAME LOCK” message on the dialog means the frame lock 
function is working. 
• This item can't be selected for no signal and sync out.
• When the MY TEXT DISPLAY is set to ON, the MY TEXT is 
displayed together with the input information in the  
INPUT_INFORMATION box (

73).
FACTORY RESET
Selecting OK using the ► button performs this function. By this 
function, all the items in all of menus will collectively return to the 
initial setting. Note that the items AUTO BLANK, STANDBY MODE, 
LAMP TIME, FILTER TIME, LANGUAGE, FILTER MESSAGE, 
NETWORK and SECURITY settings are not reset. CANCEL 
ð OK
Be sure to set ALTITUDE after resetting all the settings (
 63).  
						

							68
NETWORK menu
NETWORK menu
See the Network Guide for details of NETWORK operation.
Remember that incorrect network settings on this projector may cause trouble on 
the network. Be sure to consult with your network administrator before connecting 
to an existing access point on your network. 
						

							69
SECURITY menu
(continued on next page) This projector is equipped with security functions.
From the SECURITY menu, items shown in the table 
below can be performed.
To use SECURITY menu: User registration is required 
before using the security functions.
Enter to the SECURITY menu
1.  Press the ► button. The ENTER PASSWORD box will be displayed.  
2. 
 Use the ▲/▼/◄/► buttons to enter the registered password. 
    The factory default password is as follows.
    
    
    This password can be changed 
( below
). Move the cursor to
    the right side of the ENTER PASSWORD box and press 
    the ► button to display the SECURITY menu. • It is strongly recommended the factory default password to be 
changed as soon as possible.
• If an incorrect password is input, the ENTER PASSWORD box 
will be displayed again. If incorrect password is input 3 times, the 
projector will turn off. Afterwards the projector will turn off every time 
an incorrect password is input.
3. 
 Items shown in the table below can be performed.
If you have forgotten your password(1)  While the ENTER PASSWORD box is displayed, press and hold the 
RESET button on the remote control for about 3 seconds or press 
and hold the  INPUT button for 3 seconds while pressing the ► 
button on the projector.
(2) 
 The 10 digit Inquiring Code will be displayed. Contact your dealer   
with the 10 digit Inquiring Code. Your password will be sent after your user registration information 
is confirmed.
• If there is no key input for about 55 seconds while the Inquiring Code is displayed, the menu will 
close. If necessary, repeat the process from (1). 
 
Item Description
SECURITY 
PASSWORD  CHANGE
(1)  Use the ▲/▼ buttons on the SECURITY menu 
to select SECURITY PASSWORD CHANGE 
and press the ► button to display the ENTER 
NEW PASSWORD box.
(2) 
 Use the ▲/▼/◄/► buttons to enter the new password.
(3)  Move the cursor to the right side of the ENTER 
NEW PASSWORD box and press the ► button 
to display the NEW PASSWORD AGAIN box, 
enter the same password again. 
(4) 
 Move the cursor to the right side of the NEW 
PASSWORD AGAIN box and press the ► 
button and the NOTE NEW PASSWORD box 
will be displayed for about 30 seconds, please 
make note of the password during this time.
Pressing the ENTER button on the remote control or ► button on the 
projector will close the NOTE NEW PASSWORD box.
• Please do not forget your password.
SECURITY menu
8934A:8212
8933WB:2610 
						

							70
SECURITY menu
ItemDescription
MyScreen 
PASSWORD
The MyScreen PASSWORD function can be used to prohibit access to the 
MyScreen function and prevent the currently registered MyScreen image 
from being overwritten.
1 Turning on the MyScreen PASSWORD1-1  Use the ▲/▼ buttons on the SECURITY menu to 
select MyScreen PASSWORD and press the ► 
button to display the MyScreen PASSWORD on/
off menu.
1-2 
 Use the ▲/▼ buttons on the MyScreen 
PASSWORD on/off menu to select ON. 
The ENTER NEW PASSWORD box (small) 
will be displayed.
1-3 
 Use the ▲/▼/◄/► buttons to enter the 
password. Move the cursor to the right side 
of the ENTER NEW PASSWORD box (small) 
and press the ► button to display the NEW 
PASSWORD AGAIN box, enter the same 
PASSWORD again.
1-4 
 Move the cursor to the right side of the 
NEW PASSWORD AGAIN box and press 
the ► button to display the NOTE NEW 
PASSWORD box for about 30 seconds, 
please make note of the password during 
this time.  Pressing the ENTER button on the remote control or ► button on the 
projector will return to MyScreen PASSWORD on/of

f menu.
When a password is set for MyScreen:
• The MyScreen registration function (and menu) will be unavailable.
• The MyScreen Lock menu will be unavailable.
• The START UP setting will be locked on MyScreen (and the menu will be 
unavailable).
Turning the MyScreen PASSWORD off will allow normal operation of these 
functions.
• Please do not forget your MyScreen PASSWORD.
2 Turning off the MyScreen PASSWORD2-1  Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off 
menu.
2-2 
 Select OFF to display the ENTER 
PASSWORD box (large). Enter the registered 
password and the screen will return to the 
MyScreen PASSWORD on/off menu.
If an incorrect PASSWORD is input, the menu will 
close. If necessary, repeat the process from 2-1.
3 If you have forgotten your password3-1  Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off 
menu.
3-2 
 Select OFF to display the ENTER PASSWORD box (large). The 10 digit 
Inquiring Code will be displayed inside the box.
3-3 
 Contact your dealer with the 10 digit Inquiring Code. Your password will 
be sent after your user registration information is confirmed.
(continued on next page)
ENTER NEW PASSWORD  box (small)
ENTER PASSWORD box  (large)