Dyson Dc 7 Manual

Please read this guide carefully before use.User guide
6057-DCO7 OPS MAN (UPDATE)  10/23/01  12:26 PM  Page 1 

Assembling DCO71Slide hose into runners at
back of machine and
push down until it clicks.
2Press wand release button
and slide wand down into
hose.
DCO7 
HoseWand capUpper cable winderWandWand release button
On/off switch
Valve release clips
Soleplate Bin emptying trigger Cyclone release catch
Shroud release catch
Shroud
Filter release catch
Ready-to-go hose release 
Airway inspection valve
*Only supplied with 
floortool models
Stair tool
Crevice tool Brush tool
12
Floortool*
Slot wand into top of...

Using your DCO7Plug in at mains and press
on/off switch.
To start vacuuming, push
cleaner head down with foot
and pull handle towards you.Ensure machine is in upright
position before using tools. 
Press wand release catch 1to
release ready-to-go hose and
slide wand to end of hose.
AWand mode
Slide back wand cap and
place tools directly on to
wand handle.
Using the toolsNBYou can twist the brush and
stair tool heads to make
cleaning easier.
Anti-jam brushbar(Not available on silver/yellow model).
1
Manual...

Where to look for blockagesCheck that tools are clear of
blockages. 
Remove bin assembly from
machine.
Remove wand and check
inside for blockages. Press hose release button A
from front of machine and
slide hose out with lower
cable winder from rear. 
Check inside hose for
blockages.
ImportantPlease note that clearing
blockages is not covered by
your cleaner’s guarantee.Turn power off and unplug
before starting to clear any
blockages.NBShould any part of the
machine become blocked
it may overheat and...

Washing the lifetime pre-motor filterPress filter release catch and
remove filter housing from
machine.
Filter should be washed every
six months. Circle your two
washes.
Remove filter from housing.
Only blue foam and yellow
cage should be washed.Wash in cold water only.
Turn power off and unplug
before removing filter.
Repeat steps 1and 2until
water runs clear.Allow 12 hours for filter to dry.
Make sure it is completely dry
before replacing in machine.Replace in filter housing and
click back into...

Clean shroud with a cloth or
dry brush to remove fluff and
debris.To replace bin, first click 
rear bin catch 1and then
front bin release catch 2
into place.
Ensure bin base is closed
securely and replace bin
assembly on to machine.
Option 2AEmpty directly into dustbin.
BEnsure bin base is closed
securely and replace bin
assembly on to machine.
Emptying the clear bin
TM
ImportantBin must be emptied when
dust reaches MAXmark.
Press cyclone release catch
with thumb to remove bin
assembly.
Option 1...

Changing/fitting your belt(Silver/yellow model only)1Recommended postion 
for changing the belt, 
with wand removed.
2Undo fasteners using a
coin and remove soleplate.
3Remove any debris and
check spindle is clean.4To replace the belt - 
remove brushbar, loop
belt around brushbar
and feed through hole.
5Check end caps are 
in place.6Using the back of the
cleaner as a lever, loop
the belt around your
thumb. Stretch and
release over spindle.
Belt should be free of
twists as shown.
7Rest the three tabs on...

UK
08705 275 104
Tetbury Hill, Malmesbury, Wilts SN16 0RP.
7 days a week 8am - 8pm  e-mail: [email protected]
IRL
(01) 475 7109
Unit 2, Baldonneu Business Park, Naas Road, Co Dublin.
Visit the Dyson website for product information and to order accessories and spares.
helpline
6057-DCO7 OPS MAN (UPDATE)  10/23/01  12:26 PM  Page 14