Eiki Lc-Xnp4000 Multimedia Projector Owners Manual

							Safety Labels
8
Safety Labels
Safety labels are used on or within the projector to alert you to items \
or areas 
requiring your attention. 
WARNING LABELEMI Label
LAMP DOOR WARNING LABEL 
						

							Safety LabelsPart Names
9
Part Names
9
8
7
3
4
52
1
6
Projector
1 Control panel
Operating system.
        Filter cover
Prevents dust and other foreign particles 
from being drawn into projector.
Remove	the	filter	cover	to	clean	the	air	
filter.
  Foot adjust button
Lock / unlock the adjustable foot.
 Front adjustable foot
Extend and retract to adjust the projection 
angle.
 Anti-dust glass
Dustproof function.
 Gate Plate
Dustproof function.
 Zoom ring
Use the zoom ring to adjust the size of the 
projected image.
Rotate the zoom ring until the image is the 
desired size.
 Focus ring
Use the focus ring to focus the projector 
image.
Rotate the focus ring until the image is 
clear.
Front IR 
receiver
Outlet 
ventilation
18
The lamp unit is inside.
12
3
14
15
16
17
9Lamp door 
						

							10
Part Names
110 KEYSTONE
Adjust the vertical keystone. 
1 1 VOLUME + / -
Sound louder or lower.
11 2 INPUT
Select input source:
Note : 
If the projector can not be captured the 
signals within 15 minutes, it will be shut 
down automatically.
11 3 BLANK
Blank the projected image. The time of 
Blank mode can be set in 15 minutes, 30 
minutes or 60 minutes. The projector will 
shut down automatically after passing each 
set time.
11 4 LAMP INDICATOR
BIndicate a status in the projector.
Control Panel
10
1111
12
1318 17
151416LAMP INDICATOR POWER INDICATOR
115  (POWER)
Power On / Off.
116 POWER INDICATOR
											 Light	on	or	flash	to	indicate	the	operating	
status of the projector.
117 AUTO
Automatically adjust the setting to match 
the current input.
11 8 MENU
Display or hide the OSD main menu.
RGB 1 RGB 2
Video
S-Video DVI-I
Y,Pb,Pr 
						

							11
Part Names
Rear
A USB
Connect a USB mouse cable to a computer 
to control computer mouse functions.
B RS232
Serial data port for controlling the projector 
with  a  computer  or  other  RS-232  control 
device.
C AUDIO IN 1 & N AUDIO IN 2
Mini jack port corresponds to computer 
input.	(RGB	IN→AUDIO	IN	1,	DVI-1	IN	
→AUDIO	IN	2)
D RGB IN 
Input analog RGB signal from a computer.
E DVI-I IN
Input digital DVI-I signal from a computer.
F S-VIDEO
S-Video signal from a video source.
G AUDIO IN 3, R / L
RCA type corresponds to video input.
H LAN
P l e a s e   s e e   p a g e   3 7   N e t w o r k   C o n t r o l 
Application for details.
 I  SPEAKER
 J    COMPONENT  (  Y,  Pb,  Pr  /  Y, 
Cb, Cr)
I n p u t   C o m p o n e n t   s i g n a l   f r o m   a   D V D 
player.
 K  
VIDEO
C o m p o s i t e   v i d e o   s i g n a l   f r o m   a   v i d e o 
source.
 L RGB OUT
Connect an external monitor to this 
connection to view the “RGB IN” input.
 M AUDIO OUT
         
T h i s   j a c k   o u t p u t s   t h e   a u d i o   s i g n a l 
from  computer  signal  to  external  audio 
equipment.
O  Slot  for  Kensington  Micro  Saver 
Security System
Built-in Security Slot
This security slot supports the MicroSaver® 
Security System. MicroSaver® is a registered 
trademark of Kensington Microware Inc. 
The logo is trademarked and owned by 
Kensington Microware Inc.
P   REAR IR RECEIVER
ABC
NM
D
L
EF
K
G
J
H
P
O
I 
						

							Setting Up
12
Setting Up
When installed against a wall, leave about 20cm (7.9in.) between the p\
rojector and the wall.
8.74~10.52
5.80~7.00
4.33~5.24
2.87~3.48
2.28~2.77
1.69~2.07
1.10~1.36Distance(M)
Image size(inch)
8.74~10.52
5.80~7.00
4.33~5.24
2.87~3.48
2.28~2.77
1.69~2.07
1.10~1.36
Image size(inch)
Distance(M)
Arrangement
1. 
Before installation, make sure that the projector is turned off and the power cord is disconnected.
2.  Do not set up and move the projector, while it is hot.
3.    The distance between the projector and screen determines the actual image size. Refer to the table 
below to determine the screen size at a given distance.
Note: The dimensions in the table below are approximate.
Screen size (diagonal) Distance (m)Distance (feet)
inch mTele Wide TeleWide
40 1.01.36 1.104.473.62
60 1.52.07 1.696.785.54
70 1.82.42 1.987.936.51
80 2.02.77 2.289.097.47
100 2.53.48 2.8711.40 9.40
150 3.85.24 4.3317.18 14.21
200 5.17.00 5.8022.96 19.03
250 6.48.76 7.2728.74 23.84
300 7.610.52 8.7434.52 28.66 
						

							13
Setting Up
Power ON / OFF
Turning On The Power
1.		Make	sure	that	power	cord	is	firmly	and	
correctly connected to the projector.
2. The green Power indicator blinks slowly.
3. Remove the lens cover. 
4.   Press POWER button on the control panel or 
the remote control to turn on the projector.
5.   Rotate the zoom ring to adjust the screen size.
6. Rotate the focus ring to adjust the focus.
Turning Off The Power
1.   Press the POWER button on the control 
panel or the remote control. The "power off" 
confirmation	message	will	appear.
2.   Press the POWER button again while the 
message is shown on the screen.
3.    When the projector enters "Standby" mode, 
the green Power indicator blinks slowly.
4.    The projector cannot be turned on while red 
"Lamp indicator" is blinking slowly in cooling 
mode.
5.   If you don’t use the projector for a long time, 
remove power cord.
 WARNING

  Do not touch around the lamp cover and the 
exhaust vents during use or just after use, since it 
is too hot.
POWER indicator
AC inlet Outlet
Focus ring
Zoom ring
 WARNING

  A strong light is emitted when the projector’s 
power is on. Do not look into the lens of the 
projector or look inside of the projector through 
any of the projector’s openings.
 CAUTION
  Do not turn off the AC power for 120 seconds 
after the lamp is turned on. Doing so could cause 
premature lamp failure.
Power off?
Please press
key again to power off.
1.
2.
3.~4.
5. 
						

							14
Setting Up
Setting Up The Projector
The projector supports the following four different projection methods. 
1. Front projection
2. Rear projection3. Rear ceiling projection
4. Front ceiling projection
Special installation is required in order to suspend the projector from \
the ceiling. Please ask your 
dealer for details. 
0˚
180˚
270˚ 90˚The projector can be installed pitched by any 
angle (360 degree) without any setting in fan 
mode. As for rolling it must be within 10 degree. 
						

							15
Setting Up
Ceiling Mounted Installation Guide 
Attach	ceiling	mount	at	four-suspension	bracket	fixing	points	when	suspending	from	a	ceiling.	
Special installation is required in order to suspend the projector from \
the ceiling. Please ask your 
dealer for details.
Security Anchor
The product is equipped with security anchor and PIN 
LOCK (See page 33 for detials) functions to help prevent 
unauthorized removal of the projector.
MAX M4x8 mm For Mounting
WARNING
►Do	not	grasp	the	security	anchor	to	carry	projector,	since	it	is	not	designed	for	it.
►	 The	security	anchor	is	not	for	comprehensive	theft	prevention	measures.	It	is	intended	to	be	
used as supplemental theft prevention measure. 
						

							16
Setting Up
Adjusting The Projector’s Elevation
Use the adjustable foot at the front of the projector to set the image h\
eight.
1   Holding the projector, push the foot adjust 
buttons to loosen the front adjustable foot.
12   Position the front side of the projector to the 
desired height.
3   Release the foot adjust buttons in order to 
lock the front adjustable feet.
14   Please make sure that the front adjustable 
feet are locked.
									 Please	rotate	the	adjustable	feet	when	fine	
adjustment of tilt is needed.
 CAUTION
*  
The adjustment range of front adjustable 
foot is 0 to 8.5 degrees.
*    When the foot is adjusted, it may cause the 
shape of the projected image to become 
distorted. Use the keystone correction 
function to correct this distortion.
15 
						

							17
Setting Up
Before starting, make sure that the projector and computer are both turn\
ed off.
Connect the computer 
Connect the computer cable from the computer to the projector's RGB IN o\
r DVI-I IN.
Connect a computer cable from the MONITOR OUT to an external monitor to view the
signal on RGB IN or DVI-I IN. Tighten the screw on all connectors.
How To Connect
Laptop or desktop computer
AUDIO OUTMOUSERS-232AUDIO OUTDVI OUTVGA OUTRGB IN
AUDIO IN 
VIDEO OUT AUDIO OUT (L)&(R)
S-VIDEO OUTYPb/Cb Pr/Cr
Desktop / Lapto p
Speaker DVD Player