Eizo Coloredge Cg221 Users Manual

							
4.Plug the other end of the power cord into a power outlet. 
WARNING
Use the enclosed power cord and connect to the standard 
power outlet of your country.
Be sure to remain within the rated voltage of the power cord.
Not doing so may result in fire or electric shock.
 
The equipment must be connected to a grounded main outlet.
Not doing so may result in fire or electric shock. 
 
5.Touch the power switch while touching the Input Signal Selection  switch.
The Input Selection menu is appeared on the screen.
 
 
						

							
 
*The unit is designed to be operated with your bare fingers. If you touch\
 the 
control panel with your gloved fingers or with something left on the con\
trol 
panel, it may not work.
* If there are waterdrops or dew condensation on the control panel, or ope\
rating 
with wet fingers, it may not work properly. In that case, be sure to dry\
 or wipe it 
up before use. 
6.Change SIGNAL 1 (DVI-I Connector) in the Input Selection menu to 
ADC.
Touch the Enter switch to complete the setting and the menu closes.
 
7.Switch on the PCs power.
If an image does not appear, refer to the 6. TROUBLESHOOTING for advice.
Whenever finished, turn off the PC and the monitor.
* When turning on the monitor, the kid of the input signal (Signal1 or 2/\
Analog or 
Digital) is displayed for a few seconds on the right top corner of the \
screen.
* Adjust brightness of the screen depending on the brightness of your envi\
ronment.
* Be sure to take adequate rests. A 10-minute rest period each hour is sug\
gested.
* When changing the signal connector except ADC, open the Input Selection \
menu 
again and change the setting to Standard.
* To  the settings in the  menu through ScreenManager, the \
settings of Input Selection will revert to the default setting.
 
						

							
Two PCs can be connected to the monitor through DVI-I connector and D-su\
b mini 15 
pin connector on the back of the monitor.
 
PC 1PC 2
(EX.1) Digital ADC Signal Cable (FD-
C39 enclosed) 
+ADC-DVI display 
adapter 
(commercially 
available)
 
Signal Cable DD200 
[FD-C39](Optional)
 
DVI-D
Digital
(EX.2) Digital ADC Signal Cable (FD-
C39 enclosed) 
+ADC-DVI display 
adapter 
(commercially 
available)
 
Signal Cable (FD-
C16 enclosed) 
D-Sub 
mini 15 
pin
Analog
(EX.3) Digital ADC Signal Cable (FD-
C39 enclosed) 
+ADC-DVI display 
adapter 
(commercially 
available)
 
Signal Cable (FD-
C16 enclosed) + 
Adapter*
 
D-Sub 
15 pin
Analog
 
						

							
(EX.4)Digital DVI-D Signal Cable (FD-
C39 enclosed)
 
Signal Cable FD-C16 
enclosed) 
D-Sub 
mini 15 
pin
Analog
(EX.5) Digital DVI-D Signal Cable (FD-
C39 enclosed)
 
Signal Cable (FD-
C16 enclosed)+ 
Adapter*
 D-Sub 
15 pin
Analog
(EX.6) Analog D-Sub 
mini 15 
pin Signal Cable (FD-
C16 enclosed)
 
Signal Cable (FD-
C16 enclosed) 
+Adapter*
 D-Sub 
15 pin
Analog
  *Macintosh Adapter (Optional)
Selecting the Active Input
The Input Signal Selection switch on the control panel can be used to se\
lect either 
SIGNAL 1 or SIGNAL 2 as the active input at any time. Every time the swi\
tch is 
touched, the input changes. When switching the signal, the kind of the i\
nput signal 
(Signal 1 or 2/ Analog or Digital) is displayed for a few seconds on t\
he right top corner 
of the screen.
 
						

							
The Priority Input Signal
This function is used to select which PC will have priority to control t\
he monitor when 
utilizing two PCs. The monitor constantly checks the input signals and s\
witches 
automatically in accordance with the Input Priority setting (see tabl\
e below). Once a 
priority is set, whenever a change of signal is detected at the selected\
 input, the 
monitor will switch the input to that signal.
In this case of only one signal being present at either input, the monit\
or automatically 
detects and displays that signal.
 
Priority 
Settings Performance
1
(SIGNAL1) If signals from both inputs are present, the monitor gives 
preference of Signal 1 in the following cases.
 
l     When the power of the monitor is turned ON. 
l     When the signal input to Signal 1 is changed even if active 
input was Signal 2.
 
2
(SIGNAL2) If signals from both inputs are present, the monitor gives 
preference to Signal 2 in the following cases.
l     When the power of the monitor is turned ON. 
l     When the signal input to Signal 2 is changed even if active 
input was Signal 1.
 
Manual
The monitor will not detect signals automatically in this mode. 
Select the active input by pressing the input signal selection button 
on the monitors control panel.
 
*When 1 or 2 is selected, the power saving mode of the monitor activa\
tes only 
if both PCs are in power saving mode.
 
 
						

							
The Hood can reduce light reflection for on screen color consistency.
Setup Procedure1.Attach the top cover to either the left cover or right cover before attaching to the monitor.
* Please attach the top cover so that the visor is in back. If the visor i\
s in front, 
light will seep in through the back.
2.Attach the left cover and right cover to the monitor.
(1) Firmly attach the left cover and right cover to the monitor from beneath\
.
(2) Make sure that the rubber cushions are firmly positioned against the sid\
e of the 
monitor.
(3) Slide the top cover to close.
 
						

							
The LCD monitor can be used with an arm by removing the tilt stand and a\
ttaching the 
arm or stand to the LCD monitor.
 
*If you will use the arm or stand of other manufacturers, confirm the fol\
lowings to 
the manufacturers before selecting.
l     Hole spacing on the arm mounting: 100 mm x 100 mm (VESA 
compliant)
 
l     Supportable Weight: Total weight of the monitor (without stand) and 
attaching equipment such as a cable 
l     TÜV/GS approved arm or stand
* Please connect cables after attaching an arm stand.
 
Setup Procedure
1.Lay the LCD monitor down. Do not scratch the panel.
2.Remove the tilt stand by loosening the screws. (4 pcs of M4 x 14 BZn/Fe)
 
						

							
3.Attach an arm stand to the LCD monitor securely.
 
 
						

							
ScreenManager allows you to adjust screen performance though the main me\
nu and 
select a FineContrast mode easily.
 
*Main Menu and FineContrast menu cannot be activated at the same time.
 
1.Entering the ScreenManager
Touch the Enter switch once to display the main menu of the ScreenManage\
r. 
 
2.Making Adjustments and Settings
(1) Select the desired sub menu icon using the Directing switch and touch th\
e Enter 
switch. The sub menu appears.
(2) Use the Directing switches to select the desired setting icon and touch \
the Enter 
switch. The setting menu appears.
(3) Use the Directing switches to make all required adjustments and touch th\
e Enter 
switch to save the settings.
 
 
						

							
3.Exiting the ScreenManager
(1)To return to the main menu, select the  icon or touch the Down s\
witch 
twice, followed by the Enter switch.
(2) To exit the ScreenManager, select  icon or touch the Down switch t\
wice, 
followed by the Enter switch.
 
*Double clicking the Enter switch at any time also exits the ScreenManage\
r menu.
 
FineContrast menu
Touching the Mode switch allows you to select the best suited mode for s\
creen 
display from 4 FineContrast modes; Custom, sRGB, EMU and CAL. To exit th\
e 
menu, press the Enter switch. 
 
The following table shows all the ScreenManagers adjustment and setting\
 menus. 
* indicates adjustments of analog input only and ** indicates digita\
l input only.
Main menu Sub menu Reference
Screen Clock *
4-1. Screen Adjustment 
Phase *
Position *
Resolution *
Range Adjustment *
Smoothing 
 
Signal Filter *
Color(Custom)
*1Brightness 4-3. Color Adjustment
Temperature
 
Gamma 
Saturation 
Hue