Eizo Coloredge Cg275w Users Manual

31Chapter4SelfCalibration
 ●Setting the mode to execute SelfCalibration “Mode Selection”
Set the mode to execute SelfCalibration (CAL1/CAL2/CAL3).
Signal input is specified for each set mode.
ModeSignal inputs
CAL1 DVI
CAL2 DisplayPort-1
CAL3 DisplayPort-2
 (Mini  DisplayPort)
Procedure
1. 
C
 hoose “SelfCalibration” from the Adjustment menu, and press 
.
2.
 
C

hoose “Settings” from “SelfCalibration”, and press 
.
3.
 
C

hoose “Mode Selection” from “Settings”, and press 
.
4.
 
U

se 
 or  to...

32Chapter4SelfCalibration
 ●Setting the calibration targets “Target”
Set the calibration targets for SelfCalibration.
Procedure
1. 
C
 hoose “SelfCalibration” from the Adjustment menu, and press 
.
2.
 
C

hoose “Settings” from “SelfCalibration”, and press 
.
3.
 
C

hoose “Target” from “Settings”, and press 
.
4.
 
U

se 
 or  to select the mode to change, and press .
The target setting menu appears.
5. Use  or  to select the items to change, and press .
Setting Item Adjustable Range Setting...

33Chapter4SelfCalibration
4-3. Setting Calibration Results “Result”
The previous SelfCalibration results can be checked.Procedure
1.
 
C
 hoose “SelfCalibration” from the Adjustment menu, and press 
.
2.
 
C

hoose “Result” from “SelfCalibration”, and press 
.
3.
 
Se

lect the mode you want to check the results for with 
 or .
The Result menu appears. The date and time the last SelfCalibration was executed, and the total monitor usage time 
from the previous calibration are displayed.
4. Select...

34Chapter5PowerSavingFunctions
Chapter 5 Power Saving Functions
5-1. Setting Power Saving “Power Save”
This function allows you to set the monitor into the power saving mode according to the PC status. When the 
monitor has shifted to the power saving mode, the images on the screen are not displayed.
Attention
• Turning off the main power switch or unplugging the power cord completely shuts off power supply to the monitor.
•
 
D
 evices connected to the USB upstream port and USB downstream port work...

35Chapter5PowerSavingFunctions
5-2. Setting the power saving mode when a person leaves the monitor “EcoView Sense”
The sensor on the front side of the monitor detects the movement of a person by setting a value from “Level-1” 
to “Level-4” of the EcoView Sense function. When a person moves away from the monitor, it shifts to the 
power saving mode automatically and does not display the images on the screen to reduce the power 
consumption. When a person comes near the monitor again, it comes back...

36Chapter6Troubleshooting
Chapter 6 T roubleshooting
If a problem still remains after applying the suggested remedies, contact your local dealer.
6-1. No picture
Problem Possible cause and remedy
1. No picture
• 
P
 ower  indicator  does  not  light.•
C heck  whether  the  power  cord  is  connected  properly.
• 
T
 urn  off  the  main  power,  and  then  turn  it  on  again  a 
f

ew  minutes  later.
•

T
 urn  the  main  power  switch  on.
•

Pr
 ess 
.
•

P...

37Chapter6Troubleshooting
Problem Possible cause and remedy
•Themessageshowst hatt hei nputs ignali so ut 
o

f  the  specified  frequency  range.  (Such  signal 
f

requency  is  displayed  in  magenta.)  
Example:
fD:Dot  clock
fH: 
H
 orizontal  scan  frequency
f V:

V
 ertical  scan  frequency •

C
 heck  whether  the  PC  is  configured  to  meet  the 
r

esolution  and  vertical  scan  frequency  requirements 
o

f  the  monitor  (see  “2-1. ...

38Chapter6Troubleshooting
6-3. Other problems
Problem Possible cause and remedy
1. The adjustment menu does not appear. • C heck  whether  the  operation  lock  function  works  (see 
“

3- 6.  Locking  Buttons  “Key  Lock””  (page  25)).
2.
 
N
 o mode menu is displayed. •

C
 heck  whether  the  operation  lock  function  works  (see 
“

3- 6.  Locking  Buttons  “Key  Lock””  (page  25)).
3.
 
(
 When using EcoView Sense) 
The images remain to be displayed when 
you move...

39Chapter6Troubleshooting
6- 4. Calibration sensor and SelfCalibration problems
Problem Possible cause and remedy
1. The calibration sensor comes out auto-
matically when the main power switch is 
switched on. •
T his  is  not  a  malfunction.  The  calibration  sensor 
c

omes  out  automatically  when  the  power  is  switched 
o

n  to  check  the  operation  of  the  calibration  sensor.
2.
 
T
 he calibration sensor does not come out/
stays out. •

T
 urn  off  the ...

40Chapter7Reference
Chapter 7 Reference
7-1. How to Attach the Optional Arm
An optional arm (or an optional stand) can be attached by removing the stand section. Please refer to our web 
site for the corresponding optional arm (or optional stand). http://www.eizo.com
Attention
• When attaching an arm or stand, follow the instructions of their User’s Manual.
•
 
W
 hen using another manufacturer’s arm or stand, confirm the following in advance and select one conforming to the 
VESA standard.
- Clearance...