Electrolux Ewc 1350 User Manual

• powder detergents for all types of fabric
• powder detergents for delicate fabrics
(60°C max) and woollens
• liquid detergents, preferably for low tem-
perature wash programmes (60°C max)
for all types of fabric, or special for wool-
lens only.
The detergent and any additives must be
placed in the appropriate compartments of
the dispenser drawer before starting the
wash programme.
Prewash detergent is to be added
straight into the drum
If using liquid detergents, a programme
without prewash must be...

Programme/ Tem-
peratureType of laundryOptionsDescription of the
programme
RINSES
Spülen - Rinçages
With this programme it
is possible to rinse and
spin cotton garments
which have been
washed by hand. The
machine performs 3
rinses, followed by a fi-
nal long spin. The spin
speed can be reduced.
Spin reduction/Rinse
Hold/No Spin - Rinse
PlusRinses
Spin max. 1300 rpm
Max Load 3 kg
DRAIN
Pumpen - Vidange
For emptying out the
water of the last rinse
in programmes with
the Rinse Hold option
selected....

EXTERNAL CLEANING
Clean the exterior cabinet of the appliance
with soap and water only, and then dry
thoroughly.
CLEANING THE DISPENSER DRAWER
The washing powder and additive dispens-
er drawer should be cleaned regularly.
1. If necessary, the whole detergent draw-
er can be taken out of the machine for
cleaning. You need to pull it firmly out-
wards, so that it comes free of retaining
stop.
2. To remove the siphon at the inside
edge of the drawer for cleaning, you
need to press it inwards and pull it...

• Select the programme Drain and let it
run until it is finished.
•
Turn the programme selector to 
position. When you intend to start the
machine up again, make sure that the
room temperature is above 0 °C.The appliance is only to be used and stored
indoors at normal room temperature. The
manufacturer is not responsible for any
frost damage.
WHAT TO DO IF…
Certain problems are due to lack of simple
maintenance or oversights, which can be
solved easily without calling out an engi-
neer. Before contacting...

ProblemPossible cause/Solution
There is water on the floor:
Too much detergent or unsuitable detergent (creates too much
foam) has been used.
• Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of the inlet hose fit-
tings. It is not always easy to see this as the water runs down the
hose; check to see if it is damp.
• Check the water inlet hose connection.
The drain or inlet hose is damaged.
• Change it with a new one.
Unsatisfactory washing re-
sults:
Too...

Mod. ... ... ...
Prod. No. ... ... ...
          Ser. No. ... ... ...
TECHNICAL DATA
DimensionsWidth
Height
Depth50 cm
67 cm
55 cm
Electrical connection
Voltage - Overall power - FuseInformation on the electrical connection is given on the rating
plate, on the inner edge of the appliance door.
Water supply pressureMinimum
Maximum0,05 MPa
0,8 MPa
Maximum LoadCotton3 kg
Spin SpeedMaximum1300 rpm
CONSUMPTION VALUES
The data of this table are approximate. Different causes can change the data: the
quantity...

ProgrammesLoad
(kg)Energy con-
sumption
(kWh)Water con-
sumption (li-
tre)Approximate
programme
duration (mi-
nutes)Remaining
moisture
(%)
1)
Standard 40 °C
cotton1,50.493813753
1) At the end of spin phase.
Off Mode (W)Left On Mode (W)
0.101.10
INSTALLATION
LIFTING THE MACHINE
Be careful when lifting the machine. Incor-
rect methods of lifting can cause physical
injuries and also increase the risk of dam-
age to the machine. Open the door and
take hold of the top inside of the door
opening. You can also...

2. Return machine to its upright position
and remove the power supply cable
and the draining and inlet hose from the
hose holders on the rear of the appli-
ance.
3. With a suitable spanner unscrew and
remove the three screws and their
spacers on machines rear.
4. The three holes must then be plugged
with the plastic plug caps supplied in
the bag containing the instruction
booklet, which can be found inside the
drum.
POSITIONING
Install the machine on a flat hard floor.
Make sure that air circulation...

2. The machine end of the inlet hose can
be turned in any direction. Set the hose
correctly by loosening the ring nut. Af-
ter positioning the inlet hose, be sure to
tighten the ring nut again to prevent
leaks.
The inlet hose must not be lengthened. If it
is too short and you do not wish to move
the tap, you will have to purchase a new,
longer hose specially designed for this type
of use.
Important! Before connecting up the
machine to new pipework or to pipework
that has not been used for some time, run...

with an internal diameter at least as large as
that of the machines own hose. Use a suit-
able hose connector.
Information on the electrical connection is
given on the rating plate on the inner edge
of the appliance door.
Check that your domestic electrical installa-
tion can take the maximum load required,
also taking into account any other applian-
ces in use.
Connect the machine to an earthed
socket.
The manufacturer does not accept
any responsibility for damage orinjury through failure to comply
with...