Epson Aculaser CX16 User Manual

							2. Grab the handle and lift it up slightly to the back, and then slowly pull the photoconductor unit out
vertically.
Note:
❏Do not touch the PC drum and the transfer belt on the photoconductor unit.
❏Position the removed photoconductor unit horizontally as shown in the illustration below.
Be sure to keep the photoconductor unit horizontal and place it where it will not become dirty.
Do not leave the photoconductor unit removed for more than 15 minutes, and do not place the
removed photoconductor unit in a location where it would be exposed to direct light (such as
sunlight).
AcuLaser CX16 Series     Printer / Copier / Scanner User’s Guide
Troubleshooting     161
 
						

							3. Push the fuser separator levers back as far as possible.
c
Caution:
The area around the fuser unit is extremely hot.
Touching anything other than the indicated levers may result in burns. If you get burned,
immediately cool the skin under cold water, and then seek professional medical attention.
AcuLaser CX16 Series     Printer / Copier / Scanner User’s Guide
Troubleshooting     162
 
						

							4. Remove any misfed media.
Note:
❏If a media misfeed occurs near the fuser unit, pull out the media from below the fuser unit, as
shown in the illustration above.
❏If the media cannot be removed from below the fuser unit, raise the fuser unit cover, and then
remove the media from above the fuser unit.
AcuLaser CX16 Series     Printer / Copier / Scanner User’s Guide
Troubleshooting     163
 
						

							❏If you cannot remove paper jammed in the fuser unit, remove the fuser unit.
M
❏Remove the dust cover from Tray 1 and remove the media.
AcuLaser CX16 Series     Printer / Copier / Scanner User’s Guide
Troubleshooting     164
 
						

							Note:
❏Do not touch the surface of the fuser roller in the fuser unit.
❏Do not touch the matching connectors of the fuser unit and the machine.
AcuLaser CX16 Series     Printer / Copier / Scanner User’s Guide
Troubleshooting     165
 
						

							❏Do not touch the paper exit sensor on the fuser unit.
❏Decreased print quality may result if the surface of the transfer roller is touched.
Be careful not to touch the surface of the transfer roller.
AcuLaser CX16 Series     Printer / Copier / Scanner User’s Guide
Troubleshooting     166
 
						

							5. Return the fuser separator levers to their original positions.
6. Slowly insert the photoconductor unit vertically, and then push it slightly down toward you to
finish reinstalling the photoconductor unit.
AcuLaser CX16 Series     Printer / Copier / Scanner User’s Guide
Troubleshooting     167
 
						

							7. Carefully close the scanner unit.
Note:
Do not touch the wires and flat cable shown in the illustration.
AcuLaser CX16 Series     Printer / Copier / Scanner User’s Guide
Troubleshooting     168
 
						

							Clearing a Media Misfeed From Tray 1
1. Remove the dust cover from Tray 1.
2. Carefully pull out the misfed media.
M
Note:
If the media cannot be removed, instead of pulling it with extreme force, clear the media misfeed
according to the procedure described in “Clearing a Media Misfeed in the Machine” on page 160.
AcuLaser CX16 Series     Printer / Copier / Scanner User’s Guide
Troubleshooting     169
 
						

							3. Reattach the dust cover.
4. Press the Start key.
Clearing a Media Misfeed in Tray 2 (AcuLaser CX16NF only)
1. Pull out Tray 2 as far as possible.
AcuLaser CX16 Series     Printer / Copier / Scanner User’s Guide
Troubleshooting     170