Epson Brightlink 436wi Quick Setup Manual
Have a look at the manual Epson Brightlink 436wi Quick Setup Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Quick Setup Before using the projector, make sure you read the safety instructions in the online User’s Guide. Connect the projector Choose from the following connections. See the sections below or the online User's Guide for details. Note: A USB connection is required to use interactivity on the computer. Computer VGA cable USB cable HDMI cable USB port Connect the square end of a USB cable to the projector’s USB TypeB (square) port. Connect the flat end of the cable to any USB port on your computer. Windows® XP or later: After turning on the projector, follow the on-screen instructions to install the Epson USB Display software (EMP_UDSE.EXE; only on first connection). Note: If the software screen does not display automatically, open My Computer or Computer, then double-click EPSON_PJ_UD. Mac OS X 10.5.8 or higher: After turning on the projector, the setup folder for USB Display appears in the Finder. Double-click USB Display Installer and follow the on-screen instructions to install the Epson USB Display software (only on first connection). Monitor port Connect one end of a VGA cable to the projector’s Computer1 or Computer2 port, and the other end to your computer’smonitor port. If you are using a laptop, switch it to external display (see “Troubleshooting”). You can also connect an audio cable. HDMI port Connect one end of an HDMI cable to the projector’s HDMI port and the other end to an HDMI port on your computer. Wireless network You can connect the projector wirelessly over an 802.11b, 802.11g, or 802.11n wireless network. See “Project wirelessly” for instructions. Wired network You can connect the projector to your network using an Ethernet® cable. See “Project over a wired network” for instructions. Video device Connect up to 5 video devices and use the Source Search button on the projector or remote control to switch between them. RCA video cable (composite video) Component video to VGA cable Audio cable S-Video cable Audio cable HDMI cable Camera, USB device, or Epson document camera DC-06 Connect a digital camera, USB flash drive, USB storage device, or Epson document camera DC-06 to the projector’s USB TypeA (flat) port. If you connect a digital camera, USB flash drive, or USB storage device, you can use the projector’s Slideshow feature to project images. See the online User’s Guide for details. External monitor, external speakers, and microphone You can also connect an external monitor, external speakers, and a microphone to your projector to enhance your presentations. See the online User’s Guide for details. Turn on your projector 1 Turn on your computer or video source. 2 Plug in the projector. The power light on the projector turns orange. 3 Press thepower button on the projector or remote control. The projector beeps, the power light flashes green, and then stays on. Note: To shut down the projector, press thepower button twice, then unplug it. You don’t have to wait for the projector to cool down. 4 The default language of the menu system is English. To select another language, press the Menu button on the remote control. Select Extended and press . Select Language and press . Select your language and press . Press the Menu button to exit the menu system. Adjust the image 1 If you don’t see an image, press the Source Search button on the projector or the remote control to select the image source. Note: If you still see a blank screen or have other display problems, see the troubleshooting tips on the back of this sheet. 2 To raise the image, press the foot release button and lift the front of the projector. Release the button to lock the foot in position. 3 Press the Wide or Tele buttons on the projector to enlarge or reduce the image. 4 Turn the focus ring to sharpen the image. 5 If your image looks likeor, press theorbuttons on the projector to correct it. 6 If your image looks likeor, you’ve placed the projector off to one side of the screen at an angle. Place it directly in front of the center of the screen, facing the screen squarely. Or press theorbuttons on the projector to open the Keystone menu, and then press the Wide or Tele buttons to correct the horizontal keystone. Using the remote control Make sure the batteries are installed as shown (two AA batteries). Choose which source to displayTurn projector on and off Access projector menus Turn off projector displayGet solutions to common problems Navigate projector menus Switch between computer and Easy Interactive Pen For more information on using the remote control, see the online User’s Guide. Project wirelessly Follow the steps here to connect the projector wirelessly over an 802.11b, 802.11g, or 802.11n wireless network. You must install the optional Epson wireless LAN module (part number V12H418P12). Your computer must have a wireless card or built-in wireless interface, and be running Windows 8, Windows 7, Windows Vista®, Windows XP Professional x64, Windows XP, or Mac OS X 10.5.8 to 10.8.x. 1 Turn off the projector and unplug the power cord. 2 Remove the screw securing the wireless LAN module stopper, then remove the stopper. 3 Insert the wireless LAN module into the port. BrightLink® 436Wi *412434900**412434900*
Quick Setup Before using the projector, make sure you read the safety instructions in the online User’s Guide. Connect the projector Choose from the following connections. See the sections below or the online User's Guide for details. Note: A USB connection is required to use interactivity on the computer. Computer VGA cable USB cable HDMI cable USB port Connect the square end of a USB cable to the projector’s USB TypeB (square) port. Connect the flat end of the cable to any USB port on your computer. Windows® XP or later: After turning on the projector, follow the on-screen instructions to install the Epson USB Display software (EMP_UDSE.EXE; only on first connection). Note: If the software screen does not display automatically, open My Computer or Computer, then double-click EPSON_PJ_UD. Mac OS X 10.5.8 or higher: After turning on the projector, the setup folder for USB Display appears in the Finder. Double-click USB Display Installer and follow the on-screen instructions to install the Epson USB Display software (only on first connection). Monitor port Connect one end of a VGA cable to the projector’s Computer1 or Computer2 port, and the other end to your computer’smonitor port. If you are using a laptop, switch it to external display (see “Troubleshooting”). You can also connect an audio cable. HDMI port Connect one end of an HDMI cable to the projector’s HDMI port and the other end to an HDMI port on your computer. Wireless network You can connect the projector wirelessly over an 802.11b, 802.11g, or 802.11n wireless network. See “Project wirelessly” for instructions. Wired network You can connect the projector to your network using an Ethernet® cable. See “Project over a wired network” for instructions. Video device Connect up to 5 video devices and use the Source Search button on the projector or remote control to switch between them. RCA video cable (composite video) Component video to VGA cable Audio cable S-Video cable Audio cable HDMI cable Camera, USB device, or Epson document camera DC-06 Connect a digital camera, USB flash drive, USB storage device, or Epson document camera DC-06 to the projector’s USB TypeA (flat) port. If you connect a digital camera, USB flash drive, or USB storage device, you can use the projector’s Slideshow feature to project images. See the online User’s Guide for details. External monitor, external speakers, and microphone You can also connect an external monitor, external speakers, and a microphone to your projector to enhance your presentations. See the online User’s Guide for details. Turn on your projector 1 Turn on your computer or video source. 2 Plug in the projector. The power light on the projector turns orange. 3 Press thepower button on the projector or remote control. The projector beeps, the power light flashes green, and then stays on. Note: To shut down the projector, press thepower button twice, then unplug it. You don’t have to wait for the projector to cool down. 4 The default language of the menu system is English. To select another language, press the Menu button on the remote control. Select Extended and press . Select Language and press . Select your language and press . Press the Menu button to exit the menu system. Adjust the image 1 If you don’t see an image, press the Source Search button on the projector or the remote control to select the image source. Note: If you still see a blank screen or have other display problems, see the troubleshooting tips on the back of this sheet. 2 To raise the image, press the foot release button and lift the front of the projector. Release the button to lock the foot in position. 3 Press the Wide or Tele buttons on the projector to enlarge or reduce the image. 4 Turn the focus ring to sharpen the image. 5 If your image looks likeor, press theorbuttons on the projector to correct it. 6 If your image looks likeor, you’ve placed the projector off to one side of the screen at an angle. Place it directly in front of the center of the screen, facing the screen squarely. Or press theorbuttons on the projector to open the Keystone menu, and then press the Wide or Tele buttons to correct the horizontal keystone. Using the remote control Make sure the batteries are installed as shown (two AA batteries). Choose which source to displayTurn projector on and off Access projector menus Turn off projector displayGet solutions to common problems Navigate projector menus Switch between computer and Easy Interactive Pen For more information on using the remote control, see the online User’s Guide. Project wirelessly Follow the steps here to connect the projector wirelessly over an 802.11b, 802.11g, or 802.11n wireless network. You must install the optional Epson wireless LAN module (part number V12H418P12). Your computer must have a wireless card or built-in wireless interface, and be running Windows 8, Windows 7, Windows Vista®, Windows XP Professional x64, Windows XP, or Mac OS X 10.5.8 to 10.8.x. 1 Turn off the projector and unplug the power cord. 2 Remove the screw securing the wireless LAN module stopper, then remove the stopper. 3 Insert the wireless LAN module into the port. BrightLink® 436Wi *412434900**412434900*
5 Select the Projector Name setting, press , and enter a name (up to
16 characters long) to identify your projector over the network.
Use the displayed keyboard to enter characters. Press the arrow buttons
on the remote control to highlight the characters and press to select
them.
Note: See the online User’s Guide for information on adding passwords.
6 Select the Wired LAN menu and press .
7 Choose IP Settings and press .
8 If your network assigns addresses automatically, select IP Settings and
turn on the DHCP setting. If not, turn off the DHCP setting and enter
the projector’s IP Address, Subnet Mask, and Gateway Address,
as needed.
9 To prevent the IP address from appearing on the network standby screen,
set the IP Address Display setting to Off.
10 When you are finished, select Complete and press , then press
again to save your settings.
11 Press the Menu button to exit the menu system.
12 See “Install network software” for additional instructions.
Install network software
Install the EasyMP® Network Projection software on each computer that will
project over the network. Use the CD labeled Epson Projector Software to
install the program.
For instructions on installing and using your network software, click the icon
on your desktop to access the on-screen EasyMP Network Projection Operation
Guide. If you don’t see the EasyMP Network Projection Guide icon, you can
install it from the projector CD or go to the Epson website, as described on the
right.
To monitor and control your projector over the network, download and install
the EasyMP Monitor software and manual from the Epson support web site.
You can install a link to the downloads page from the projector CD or go to the
Epson website, as described on the right.
4 Replace the wireless LAN module stopper and secure it using the screw
you removed.
5 Plug in and turn on the projector.
6 To configure your projector for your wireless network, do one of
the following:
• If you’re using the optional Quick Wireless Connection USB key
(Windows only), insert it into the projector’s USB TypeA port, wait
for the displayed message, remove the key, and connect it to a USB
port on your computer. Follow the on-screen instructions to install
the driver, then run your presentation. For details, see the online
User’s Guide.
• If you’re not using the key, continue with these steps.
7 Press the Menu button on the remote control, select the Network
menu, and press .
8 Choose Network Configuration and press .
9 Select the Basic menu and press .
10 Select the Projector Name setting, press , and enter a name (up to
16 characters long) to identify your projector over the network.
Use the displayed keyboard to enter characters. Press the arrow buttons
on the remote control to highlight the characters and press to select
them.
Note: See the online User’s Guide for information on adding passwords.
11 Select the Wireless LAN menu and press .
EPSON and EasyMP are registered trademarks, and EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporation. BrightLink and PrivateLine are registered trademarks \
of Epson America, Inc.
General Notice: Other product names used herein are for identification p\
urposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those \
marks.
This information is subject to change without notice.
© 2012 Epson America, Inc. 10/12 Printed in XXXXXX CPD-38375
12 Select the Connection Mode setting, press , and choose one of these
options:
• Quick to connect the projector to one computer on the network
(Ad Hoc)
• Advanced to connect the projector to multiple computers on
the network (infrastructure)
13 If you selected Quick connection mode, select the Channel setting for
your wireless network, select the type of wireless network you are using
as the Wireless LAN Sys. setting, and turn on the SSID Auto Setting
setting. Then go to step 15.
14 If you selected Advanced connection mode, select the type of wireless
network you are using as the Wireless LAN Sys. setting, and then enter
your network SSID (up to 32 characters) as the SSID setting.
If your network assigns addresses automatically, select IP Settings and
turn on the DHCP setting. If not, turn off the DHCP setting and enter
the projector’s IP Address, Subnet Mask, and Gateway Address,
as needed.
15 To prevent the SSID and IP address from appearing on the network
standby screen, set the SSID Display and/or IP Address Display settings
to Off.
16 When you are finished, select Complete and press , then press
again to save your settings.
17 Press the Menu button to exit the menu system.
18 See “Install network software” for additional instructions.
Project over a wired
network
Follow the steps here to configure your projector for your wired network using
the projector’s menu system.
1 Plug in and turn on the projector.
2 Press the Menu button on the remote control, select the Network menu,
and press .
3 Select Network Configuration and press .
4 Select the Basic menu and press .
Troubleshooting
If you see a blank screen or the No signal message after turning on your
computer or video device, check the following:
• Make sure the power light on the projector is green and not flashing,
and that the A/V Mute button on the remote has not been pressed.
• Press the Source Search button on the projector or the remote control
to select the computer as the image source.
• If you’re using a Windows notebook, press the function key on your
keyboard that lets you display on an external monitor. It may be labeled
CRT/LCD or have an icon such as. You may have to hold down the
Fn key while pressing it (such as Fn + F7). Wait a moment for the display
to appear.
• If you’re using a Mac laptop, open System Preferences and select
Displays. Select the VGA Display or Color LCD option if necessary,
then click the Arrange or Arrangement tab, and select the Mirror
Displays check box.
Where to get help
Manuals
For more information about using the projector, click the icons on your
desktop to access the online manuals (may require an Internet connection).
If you don’t have icons to the manuals, you can install a link to the download
page from the projector CD or go to the Epson website, as described below.
Telephone Support Services
To use the Epson® PrivateLine® Support service, call (800) 637-7661. This
service is available for the duration of your warranty period. You may also
speak with a projector support specialist by dialing (562) 276-4394 (U.S.) or
(905) 709-3839 (Canada).
Support hours are 6 am to 8 pm, Pacific Time, Monday through Friday, and 7 am
to 4 pm, Pacific Time, Saturday
Days and hours of support are subject to change without notice. Toll or long
distance charges may apply.
Internet Support
Visit www.epson.com/support (U.S.) or www.epson.ca/support
(Canada) for solutions to common problems. You can download utilities and
documentation, get FAQs and troubleshooting advice, or e-mail Epson.
Registration
Register today to get product updates, special promotions, and customer-only
offers. You can use the CD included with your projector or register online at
www.epson.com/webreg.
Optional accessories
For a list of optional accessories, see the online User’s Guide.
You can purchase screens or other accessories from an Epson authorized
reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you
can purchase online at www.epsonstore.com (U.S. sales) or www.epson.ca
(Canadian sales).
5 Select the Projector Name setting, press , and enter a name (up to
16 characters long) to identify your projector over the network.
Use the displayed keyboard to enter characters. Press the arrow buttons
on the remote control to highlight the characters and press to select
them.
Note: See the online User’s Guide for information on adding passwords.
6 Select the Wired LAN menu and press .
7 Choose IP Settings and press .
8 If your network assigns addresses automatically, select IP Settings and
turn on the DHCP setting. If not, turn off the DHCP setting and enter
the projector’s IP Address, Subnet Mask, and Gateway Address,
as needed.
9 To prevent the IP address from appearing on the network standby screen,
set the IP Address Display setting to Off.
10 When you are finished, select Complete and press , then press
again to save your settings.
11 Press the Menu button to exit the menu system.
12 See “Install network software” for additional instructions.
Install network software
Install the EasyMP® Network Projection software on each computer that will
project over the network. Use the CD labeled Epson Projector Software to
install the program.
For instructions on installing and using your network software, click the icon
on your desktop to access the on-screen EasyMP Network Projection Operation
Guide. If you don’t see the EasyMP Network Projection Guide icon, you can
install it from the projector CD or go to the Epson website, as described on the
right.
To monitor and control your projector over the network, download and install
the EasyMP Monitor software and manual from the Epson support web site.
You can install a link to the downloads page from the projector CD or go to the
Epson website, as described on the right.
4 Replace the wireless LAN module stopper and secure it using the screw
you removed.
5 Plug in and turn on the projector.
6 To configure your projector for your wireless network, do one of
the following:
• If you’re using the optional Quick Wireless Connection USB key
(Windows only), insert it into the projector’s USB TypeA port, wait
for the displayed message, remove the key, and connect it to a USB
port on your computer. Follow the on-screen instructions to install
the driver, then run your presentation. For details, see the online
User’s Guide.
• If you’re not using the key, continue with these steps.
7 Press the Menu button on the remote control, select the Network
menu, and press .
8 Choose Network Configuration and press .
9 Select the Basic menu and press .
10 Select the Projector Name setting, press , and enter a name (up to
16 characters long) to identify your projector over the network.
Use the displayed keyboard to enter characters. Press the arrow buttons
on the remote control to highlight the characters and press to select
them.
Note: See the online User’s Guide for information on adding passwords.
11 Select the Wireless LAN menu and press .
EPSON and EasyMP are registered trademarks, and EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporation. BrightLink and PrivateLine are registered trademarks \
of Epson America, Inc.
General Notice: Other product names used herein are for identification p\
urposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those \
marks.
This information is subject to change without notice.
© 2012 Epson America, Inc. 10/12 Printed in XXXXXX CPD-38375
12 Select the Connection Mode setting, press , and choose one of these
options:
• Quick to connect the projector to one computer on the network
(Ad Hoc)
• Advanced to connect the projector to multiple computers on
the network (infrastructure)
13 If you selected Quick connection mode, select the Channel setting for
your wireless network, select the type of wireless network you are using
as the Wireless LAN Sys. setting, and turn on the SSID Auto Setting
setting. Then go to step 15.
14 If you selected Advanced connection mode, select the type of wireless
network you are using as the Wireless LAN Sys. setting, and then enter
your network SSID (up to 32 characters) as the SSID setting.
If your network assigns addresses automatically, select IP Settings and
turn on the DHCP setting. If not, turn off the DHCP setting and enter
the projector’s IP Address, Subnet Mask, and Gateway Address,
as needed.
15 To prevent the SSID and IP address from appearing on the network
standby screen, set the SSID Display and/or IP Address Display settings
to Off.
16 When you are finished, select Complete and press , then press
again to save your settings.
17 Press the Menu button to exit the menu system.
18 See “Install network software” for additional instructions.
Project over a wired
network
Follow the steps here to configure your projector for your wired network using
the projector’s menu system.
1 Plug in and turn on the projector.
2 Press the Menu button on the remote control, select the Network menu,
and press .
3 Select Network Configuration and press .
4 Select the Basic menu and press .
Troubleshooting
If you see a blank screen or the No signal message after turning on your
computer or video device, check the following:
• Make sure the power light on the projector is green and not flashing,
and that the A/V Mute button on the remote has not been pressed.
• Press the Source Search button on the projector or the remote control
to select the computer as the image source.
• If you’re using a Windows notebook, press the function key on your
keyboard that lets you display on an external monitor. It may be labeled
CRT/LCD or have an icon such as. You may have to hold down the
Fn key while pressing it (such as Fn + F7). Wait a moment for the display
to appear.
• If you’re using a Mac laptop, open System Preferences and select
Displays. Select the VGA Display or Color LCD option if necessary,
then click the Arrange or Arrangement tab, and select the Mirror
Displays check box.
Where to get help
Manuals
For more information about using the projector, click the icons on your
desktop to access the online manuals (may require an Internet connection).
If you don’t have icons to the manuals, you can install a link to the download
page from the projector CD or go to the Epson website, as described below.
Telephone Support Services
To use the Epson® PrivateLine® Support service, call (800) 637-7661. This
service is available for the duration of your warranty period. You may also
speak with a projector support specialist by dialing (562) 276-4394 (U.S.) or
(905) 709-3839 (Canada).
Support hours are 6 am to 8 pm, Pacific Time, Monday through Friday, and 7 am
to 4 pm, Pacific Time, Saturday
Days and hours of support are subject to change without notice. Toll or long
distance charges may apply.
Internet Support
Visit www.epson.com/support (U.S.) or www.epson.ca/support
(Canada) for solutions to common problems. You can download utilities and
documentation, get FAQs and troubleshooting advice, or e-mail Epson.
Registration
Register today to get product updates, special promotions, and customer-only
offers. You can use the CD included with your projector or register online at
www.epson.com/webreg.
Optional accessories
For a list of optional accessories, see the online User’s Guide.
You can purchase screens or other accessories from an Epson authorized
reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you
can purchase online at www.epsonstore.com (U.S. sales) or www.epson.ca
(Canadian sales).