Epson Brightlink 436wi Technical Manual

Installation Guide
Guide d’installation
Installation.book  Page 1  Tuesday, October 30, 2012  5:53 PM 

2
Safety Instructions
For your safety, read all the instructions in this guide before using the wall mount. Incorrect handling that  
ignores instructions in  this guide could damage the wall mount or could result in personal injury or property  
damage. Keep this installation guide on hand for future reference. 
Read the safety instructions in the  User's Guide for your projector and follow the instructions in this document.
Explanation of Symbols
The warning marks shown below are used throughout...

3
English
The installation work should be performed by at least two qualified service personnel. If you need to  
loosen any screws during installation,  be careful not to drop the wall mount. 
If the wall mount or projector falls, it coul d cause personal injury or property damage. 
When you mount the projector on the wall with the wall mount, the wall requires enough strength to hold  
the projector, the interactive module, and the wall mount.  
This wall mount should be installed on a concrete wall....

4
Location
•Determine where you will install the wall mount and prepare the location in advance. Also, make sure  
there is a gap of 16 to 26 inches (410 to 660 mm) from the top of the image projected onto the white  
board to the ceiling. See “Positioning the  Projector” on page 14 for more details.
•Do not install the projector in a location where it might be subjected to vibration or shock. Vibration or  
shock could cause damage to the projector or mounting  surface. It could also cause the wall...

5
English
1Package Contentss6
2Specificationss7
3Connecting Devices
1. Connecting Computers
2. Connecting Through a Network
3. Connecting Document Cameras
4. Using a Switch Box
5. Connecting Video Equipment
6. Connecting Audio
s9
4Positioning the Projector
1. Installation Measurements for BrightLink 425Wi/435Wi/436Wi and PowerLite 
425W/435W - Wide
2. Installation Measurements for BrightLink 425Wi/435Wi/436Wi and PowerLite 
425W/435W - Tele
3. Installation Measurements for BrightLink 421i/430i and...

6
1 Package Contents
•Use the bolts or screws supplied with the wall mount to install it as directed in this guide. Do not 
substitute these bolts with any other types.
•Use the bolts or screws supplied with the interactive module (included with BrightLink 425Wi/430i/435Wi 
only; boxed separately) to attach it as directed in this guide. Do not substitute these bolts with any other 
types.
•You need to use commercially available M8 × 50 mm anchors (at least 3) to attach the wall plate to the 
wall....

7
English
2Specifications
ItemSpecification
Wall mount
Weight Approx. 22 lb (10 kg)
Maximum load capacity 12.1 lb (5.5 kg)
Arm length 59.4 inches (1510 mm) (from wall plate attachment point to arm cover point)
Vertical angle adjustment range 0 to 5.3 inches (0 to 134 mm) (arm length minimum)
0 to 9.1 inches (0 to 230 mm) (arm length maximum)
Vertical tilt adjustment range 0 to -9.5°
Horizontal rotation adjustment range 0 to ± 5°
Horizontal roll adjustment range 0 to ± 5°
Horizontal slide adjustment range...

8
Wall plate
18 in. (457 mm)
8 in. (203 mm)
4.2 in.(107 mm)3.0 in.(75 mm)4.4 in. (112 mm)0.6 in. (15 mm)
1.8 in.(46.3 mm)
4.7 in.(120 mm)
6.3 in. (160 mm)
8.9 in. (225 mm)9 in. (230 mm)9.7 in. (247 mm)
9.8 in. (248 mm)
Installation.book  Page 8  Tuesday, October 30, 2012  5:53 PM 

9
English
3Connecting Devices
Make sure you have the power cord, computer VGA cable, and other parts at the location where the wall 
mount is to be installed.
Make sure you also have all necessary cables for devices, such as a document camera or microphone, that you 
will connect to the projector. This includes cables for any optional equipment that may be connected in the 
future. For details, refer to the User's Guide on the projector CD or at epson.com/support/
brightlinkdownloads (U.S.) or...

10
Connecting Computers
You can use any of the following ports to connect computers to the projector:
•Computer1 or Computer2 (VGA connections)
•HDMI
•USB TypeB (USB display, not recommended because of reduced interactive performance)
•Video (composite video)
•LAN (RJ-45)
If you connect VGA cables to both the Computer1 and Computer2 ports, make sure you label the cables. The 
teacher or other user needs to know which port is being used so that the correct source for full interactivity 
can be selected in...