Faroudja Fdp-Dila2 Installation And Operations Manual

11
Controls and Features
Connector Panel
1PC (computer) 1 input terminal (D-sub 3-row 15 
pin)
This is an input terminal dedicated to computer signals
(RGB video signals and sync signals).
Connect the display output terminal of the computer to 
this terminal. When a Macintosh computer is to be
connected, use the supplied conversion adapter for Mac.
Note
•When computer-related signals are input, the uppermost
edge of the image may appear to bow if the sync signal
input is composite sync (Cs) or G on sync...

12
Controls and Features 
Remote Control Unit
On the remote control, the same buttons as on the control 
panel of the projector are provided except for the following 
buttons. For the same buttons, operation is the same in 
principle.
For remote control only:
DIGITAL ZOOM T/W, QUICK ALIGN., FREEZE, ZOOM T/
W, FOCUS +/–, SCREEN W/S, PC 1, PC 2, VIDEO, Y/C, 
DVI, COMP. See insert for instructions on Learning Remote.
1Remote control’s signal transmitter
2OPERATE button
When the projector is in the stand-by...

13
Controls and Features
rDIGITAL ZOOM T/W buttons
A part of image can be magnified up to four times on the 
screen.
Each time the T or W button is pressed, the image is 
enlarged or the enlarged image is reduced by a certain 
degree. (Refer to page 37.)
*Images which are enlarged with the digital zoom become 
less clear.
*Depending on the video signal source (UXGA, etc.), this 
button does not work.
tPC buttons
Use these buttons to select a device connected to the PC 
1, PC 2 or DVI terminals. (Refer to...

14
Controls and Features 
Installing Batteries
Install batteries in the remote control. If the remote control has started to work erratically, replace the 
batteries.
1Open the back cover.
Open the back cover in the direction of the arrow.
2Install the batteries.
Place the two supplied batteries (AA/R6-size) in the 
remote control as illustrated below.
3Close the back cover.
First fit the claws on the back cover in the case, then 
close the back cover in the direction of the arrow.
Precautions for using...

15
Installing the Projector
Precautions for Installation
CAUTIONS
1. Before installation, do not connect the projector’s power cord.
2. Do not install the projector in the following places:
•Where there is water, humidity or dust.
•Where the projector may be subjected to oil, smoke or cigarette smoke.
•On a soft surface such as a carpet or cushion.
•Where the projector may be subjected to direct sunlight.
•Where temperature is high or humidity is low.
Allowable operation temperature range: 41°F to 95°F...

16
Installing the Projector 
Adjusting the Inclination of the Projector
The vertical angle and the leveling of the projector can be adjusted with the adjustable feet at the bottom of the projector.
■Adjusting the vertical angle of the projector
While pushing the levers on both sides upward, raise the projector. The adjustable feet automatically extend.
To retract the feet, push the levers and lower the projector slowly; the projector is fixed at the position
where you release the levers.
■Leveling the...

17
Installing the Projector
Installing the Projector against the Screen
The projector should be placed so that the center line of the lens is at a right angle to the screen as shown in the following 
figures.
■Side view■Top view
■Trapezoidal-distortion correctable maximum angle
The projector has a function to correct the trapezoidal distortion of the projected image on the screen.
To correct this distortion, use the KEYSTONE buttons on the projector. (Refer to “Removing the Trapezoidal Distortion of the...

18
Installing the Projector 
Projection Distance and Screen Size
•The range of projection distances that can be focused depends on the lens unit (optional) to be used. When the aspect ratio 
of the screen is 4:3, the range is as follows and you need to install the projector within this range.
Lens type
Approximate projection distance 
GL-M2910G 0.77 m to 4.03 m
GL-M2915SG 1.76 m to 4.50 m
GL-M2920ZG 2.77 m to 19.71 m
GL-M2930SZG 4.74 m to 29.87 m
*:The value for projection distance is a guide (reference)...

19
Installing the Projector
Setting the Amount of Lens Shifting
When the lens unit (optional) with the lens shifting function is used, the projected screen can be shifted up and down in 
position.
Notes
•The amount of shifting is within the range of approx. 30% to 55%.
•After finishing the lens shift setting, tighten the SHIFT LOCK fixing bolt firmly so that the lens will not move.
1Turn the cap on the top of the projector to open it.
2Loosen the SHIFT LOCK fixing bolt.
Use the hex. wrench supplied....

20
Installing the Projector 
Effective Range and Distance of the Remote Control Unit
The remote control unit can be used as either a wireless remote control unit or a wired one.
■Using as a wireless remote control unit
Aim the remote control unit toward the remote sensor on the front or the rear of the projector.
The operable distance of the remote control unit is about 10 m for direct reception. The remote control unit can be used by 
having it reflected on the screen. In this case, the total distance...