Fujitsu B24w 5 Eco Operating Manual

							Important notes
Important notes
Importantnotes NotesIn this chapter you willfind information regarding safety which it is essential to
take note of when working with your device.
Safety instructions
This device complies with the relevant safety regulations for data processing equipment,
including electronic office machines for use in an office environment. If you have any
questions, contact your salesoutlet or our Help Desk.
• The display surface of the device is sensitive to pressure andscratches. You should therefore
be careful with the display surface in order to avoid lasting damage (scratches).
• If the device is brought into the installation site from a cold environment, condensation
can form. Before operating the device, wait until it is absolutely dry and has reached
approximately the same temperature as the installation site.
• When installing and operating the device, please observe the notes on environmental
conditions in Chapter
Technicaldata,Page25as well as the instructions in Chapter
Settingupanergonomicvideoworkstation,Page8.
• To ensure sufficient ventilation, the air inlet and outlet openings of the device must be kept clear.
• The device automatically sets itself to the correct voltage within the range from 100 V to 240 V.
Make sure that the local mainsvoltage is neither higher nor lower than this range.
• Ensure that the power socket on the device and the mains outlet are freely accessible.
• The ON/OFF switch does not disconnect the monitor from the mains voltage. To disconnect
fully from the mains supply,disconnect the power plug from the socket.
• The device is equipped with a power cable that complies with safety standards.
• Use the supplied power cable only.
• Lay the cables in such a way that they do not create a hazard (danger of tripping)
and cannot be damaged. When connectingthe device, observe the relevant
notes in chapter
Connectingthedevice,Page11.
• No data transfer cables should be connected or disconnected during a thunderstorm.
• Make sure that no objects (e.g. jewellery chains, paper clips, etc.) or liquids get
inside the device (danger of electric shock, short circuit).
• The device is not waterproof!Never immerse the device in water and protect
it from spray water (rain, sea water).
• In emergencies (e.g. damaged casing, elements or cables, penetration of
liquids or foreign matter), switch off the device, disconnect the power plug and
contact your sales outlet or our Help Desk.
• Repairs to the device must only be performed by qualified technicians. Unauthorised opening
and incorrect repair may greatly endanger the user (electric shock,fire risk).
• Only use the screen resolution settings and refresh rates specified in Chapter

Technicaldata,Page25. Otherwise you may damage the device. If you are in
any doubt, contact your sales outlet or our Help Desk.
• Use a screen saver with moving images and activate the power management for
your monitor to prevent still images from burning in.
• If you operate the device with the swivel arm or wall bracket, it must not be turned by 180°.
A26361-K1334-Z220-1-7619, edition 1 3
 
						

							Important notes
• The device may only be operated in the wide format (0° landscape mode). The buttons of
the control panel are located at the bottom in the middle of the monitor.
• Store this manual close to the device. If you pass the device on to third
parties, you should pass this manual on with it.
• We recommend that you place your device on a durable, non-slip surface. In view
of the many differentfinishes and varnishes used on furniture, it is possible that the
feet of the device may mark the surface they stand on.
• To ensure sufficient ventilation, the air supply and air outlet openings of
the monitor must never be blocked.
Power cable
Use the supplied power cable only.
Use the following guidelines if it is necessary to replace the original cable set.
• The female/male receptacles of the cord set must meet IEC60320/CEE-22 requirements.
• The cable has to be HAR-certified or VDE-certified. The mark HAR or
VDE will appear on the outer sheath.
• For devices which are mounted on a desk or table, type SVT or SJT cable sets may be
used. For devices which sit on thefloor, only SJT type cable sets may be used.
• The cable set must be selected according to the rated current for your device.
• If necessary, replace the original power cable with a regular grounded 3-core mains lead.
Transporting the deviceDevice , Tr ans por ta ti on
RetransportationTransport all parts separately in their original packaging or in a packaging which
protects them from knocks and jolts, to the new site.
Do not unpack them until all transportation manoeuvres are completed.
If the device is brought from a cold environment into the room where it will be used,
condensation may occur. Before operating the device, wait until it is absolutely dry
and has reached approximately the same temperature as the installation site.
Cleaning the device
Switch off the device and unplug the power plug.
Do not clean any interior parts yourself, leave this job to a service technician.
Do not use any cleaning agents that contain abrasives or may corrode plastic.
Ensure that no liquid enters the device.
The display surface of the device is sensitive to pressure and scratches. Clean
it only using a soft, slightly moistened cloth.
The surface of the casing can be cleaned with a dry cloth. If particularly dirty, use a cloth that
has been moistened in mild domestic detergent and then carefully wrung out.
4 A26361-K1334-Z220-1-7619, edition 1
 
						

							Important notes
CE marking
The shipped version of this device complies with the requirements of EEC
directives 2004/108/EC Electromagnetic compatibility and 2006/95/EC
Low voltage directive.
Energy StarEnergyS tarThe Fujitsu LCD colour monitor is equipped with a power management
system which reduces the power draw in OFF mode to less than 1 W.
As a result, the LCD monitor satisfies the requirements of the U.S.
Environmental Protection Agency (EPA).
The EPA estimates that computer equipment uses approximately 5 % of all business
electricity and that this is growing rapidly. If all desktop PCs and peripherals were to enter
a low-power mode when not in use, the overall electricity saving could amount to $ 2 billion
annually. These savings could also prevent the emission of 20 million tons of carbon dioxide
into the atmosphere - equivalent to the discharge from 5 million cars.
As an Energy Star Partner, Fujitsu Technology Solutions GmbH has determined that this
product meets the Energy Star guidelines for energy efficiency.
A26361-K1334-Z220-1-7619, edition 1 5
 
						

							Important notes
Disposal and recycling
This device has been manufactured as far as possible from materials which can be recycled or
disposed of in such a way that the environment isnot damaged. The device may be taken back after
use to be reused or recycled, provided that it is returned in a condition that befits its intended use.
Any components not reclaimed will be disposed of in an environmentally acceptable manner.
The device must be disposed of in accordance with local regulations for disposal of special
waste. The screen background lighting contains mercury. You must observe the applicable
handling and disposal safety regulations forfluorescent tubes.
If you have any questions regarding disposal, please contact your local sales office, our Help Desk, or:
GermanyBelgium
Switzerland
Fujitsu Technology
Solutions GmbH
Remarketing and Recycling
D-33106 Paderborn, Germany
Tel.: +49 5251 / 81 80 10
Fax: +49 5251 / 81 80 15

http://ts.fujitsu.com/wvm
RECUPEL
Boulevard Reyers, 80
B-1030 Brussels
Tel.: +32 2 / 706 86 16
Fax: +322/7068613
E-mail: [email protected]

http://www.recupel.be
SWICO
Schweizerischer
Wirtschaftsverband der
Informations-, Kommunikations-
und Organisationstechnik
(Swiss Trade Association
for Information,
Communications and
Organisational Technology).
For a list of SWICO
disposal sites, see:

http://www.swico.ch
Asia
USA
Taiwan: Environmental
Protection Administration
Executive, Yuan, R.O.C.

http://recycle.epa.gov.tw
Fujitsu America Inc.
1250E. Arques Avenue
Sunnyvale, CA 94085, U.S.A.
Contact: Bernd Henning
Phone No.: (408) 329-6737
Fax No.: (408) 746-8299
Information on this subject is also available on the Internet athttp://ts.fujitsu.com/recycling.
6 A26361-K1334-Z220-1-7619, edition 1
 
						

							Getting started
Getting started
Unpacking and checking the delivery
The display surface of the device is sensitive to pressure and scratches.
Always hold the device by the casing!
The complete device package includes:
• one monitor
• one data cable (D-SUB)
• one data cable (DVI-D)
• one audio cable
• one power cable
• one CD with software and documentation
• one Warranty Booklet
• one Safety manual
►Unpack all the individual parts.
►Check the contents of the package for any visible damage caused during transport.
►Check whether the delivery conforms to the details in the delivery note.
►Should you discover that the delivery does not correspond to the delivery
note, notify your local sales outlet immediately.
Do not discard the original packing material of the devices. You may need the
packaging in the future if you need to transport your device.
Settingupthedevice
To ensure sufficient ventilation, the air inlet and outlet openings of
the device must be kept clear.
A26361-K1334-Z220-1-7619, edition 1 7
 
						

							Getting started
Setting up an ergonomic video workstation
1
►Do not position the video workstation
opposite a window (1).
1►Position the monitor outside the reach
of a light source (1).
1
►Position the keyboard where it is
easiest to reach (1).
8 A26361-K1334-Z220-1-7619, edition 1
 
						

							Getting started
1
50 cm
►Position the monitor so that the eye distance
to the screen (1) is around 50 cm.
30
30 65
65 0
60
1
2 2►Position the monitor for optimum viewing
(1). The monitor should under no
circumstances fall outside the permissible
viewing space (2).
Depending on the situation, it may be advisable to use a swivel arm or wall
bracket (VESA FPMPMI), which are available from specialist dealers. For
this purpose the monitor base must be removed beforehand as described
in Chapter
Removingmonitorbase,Page10.
Adjusting the height
The height of the monitor can be adjusted by approximately 110 mm.
►Grasp the monitor with both hands on the right and left edge of the casing
and move it upward or downward.
Adjusting the inclination
The inclination of the monitor can be adjusted by -5° (forward) and +20°
(backwards) from its vertical position.
►Hold the monitor with both hands on the left and right sides of the casing
and move it to the desired angle.
Adjusting the rotation
►Grasp the monitor with both hands on the right and left edge of the casing
and turn it to the desired position.
A26361-K1334-Z220-1-7619, edition 1 9
 
						

							Getting started
Removing monitor base
Before you can use a swivel arm or a wall bracket, you must remove the monitor base.
The display surface is susceptible to scratching!
►Switch off the monitor and pull the power
plug out of the power socket.
►Lay the monitor on its face on a soft surface.
►Remove the cover and disconnect all cables.
►Remove the screws (1) on the rear
of the monitor.
You can now mount a swivel arm or
a wall bracket as per VESA FPMPMI
with 100 mm hole spacing.
For instructions on how to mount the swivel arm or wall bracket, please see
the documentation for the swivel arm or wall bracket.
Assemble wall bracket (optional)
For further information, please see the documentation regarding the VESA FPMPMI wall bracket.
Only use UL-approved fastening brackets with a minimum load bearing capacity of 4.9 kg.
Observe the correct hole spacing (distance between screws) of 100 mm x 100 mm.
OnlyuseM4x10mmscrews.
►Attach the fastening bracket to the wall bracket.
►Mount the monitor on the wall in accordance with the documentation regarding
the VESA FPMPMI wall bracket.
10 A26361-K1334-Z220-1-7619, edition 1
 
						

							Getting started
Connecting the device
Please observe the safety information inImportantnotes,Page3.
CE conformance and optimum picture quality are guaranteed only if
you use the data cables supplied.
►Switch off the monitor and the computer.
►Disconnect the power plug from the computer.
Connecting cables to the monitor
The data cables supplied have two 15-pin D-SUB connectors or two 24-pin DVI
connectors for connection to the monitor and to the computer.
Information on the computer connections and interfaces is contained in the
operating manual for the computer.
1 = Power connector
2 = AUDIO-IN socket
3 = DVI-D connector (DIGITAL)4 = D-SUB socket (ANALOG)
5 = Security slot for Kensington Lock
6 = Holes forfixing swivel arm or wall bracket
►Select the data cable which is suitable for your computer.
A26361-K1334-Z220-1-7619, edition 1 11
 
						

							Getting started
►Connect one of the connectors of the data cable to the D-SUB socket or DVI-D socket of
the monitor and secure the plug-in connection by tightening the safety screws.
The monitor automatically detects the input when only one signal source is connected.
►Insert one plug of the audioline in the AUDIO IN socket on the monitor
and make sure it is properlyengaged.
►Plug the power cable supplied into the power connector of the monitor.
►Secure the cover over the connections.
A lock (Kensington Lock) can be mounted in the security slot to protect the monitor
from theft. A KensingtonLock is not included with the monitor at delivery.
Connecting cables to the computer
Information on the computer connections and interfaces is contained in the
operating manual for your computer.
►Connect the data cable to the (active) monitor port on the computer and secure
the plug-in connection by tightening the safety screws.
►Insert the other plug of the audio cable in the audio output of the computer.
►Plug the power connector of the monitor into a properly grounded mains outlet.
►Plug the power connector of the computer into a properly grounded mains outlet.
If your computer has two monitor ports (onboard screen controller and separate
graphics card), the monitor port for the separate graphics card is active as standard.
12 A26361-K1334-Z220-1-7619, edition 1