Fujitsu P42hta51 Users Manual

							
E-21
English
Deutsch
Espa
ñol
Fran
çais
Italiano
Portugu
ês
日 本 語
Póññêèé
中文
Color Temp.
“Color Temperature” can be set.
Each time 
E or F is pressed, the color temperature mode is switched as shown below.
<
 Warm < Standard < Cool < 
[Warm]: More reddish colors
[Cool]: More bluish colors
Press 
< to store.
Picture Memory
The adjustment status of eight gr oups of picture adjustment settings can be stored, enabling you to 
quickly switch to your desired  group of settings for the picture you are planning to watch.
[Load] : Use 
C or D to select Memory 1 - 8. When < is pressed, the valu es becomes the picture 
adjustment values stored in the selected Memory.
[Save] : Use 
C or D to select Memory 1 - 8. If < is pressed, the curre nt picture adjustment 
values are stored to the selected Memory.
Picture Memory Selection Screen
“Save” Selection Screen “Load” Selection Screen
Note
• The screen display disappears if there is no  operation within approximately 60 seconds.
• Depending on the model or the optional devices,  some of the functions may not be available.
• The adjustment range varies according to  the display signals. Make adjustments to your preferred picture quality within the adjustment range.
• Depending on the type of signal, it may not be po ssible to make some of the settings or adjustments.
01_E_7473.book  21 ページ  ２００６年 ９月６日　水曜日　午後２時３６分
 
						

							
E-22
ADJUSTING SCREEN POSITION AND SIZE 
• You can make changes to all screen adjustment options in the POSITION/SIZE Menu. See Page 
E-19 for the basic operation procedures.
• The changes you make will  be stored for the selected input mode .  Therefore, you need to select a 
desired input mode befo re making any changes.
Screen Position
Horizontal position (Horizontal)
F: Moves screen to the right.
E: Moves screen to the left.
Vertical position (Vertical)
C: Moves screen up.
D: Moves screen down.
Press 
< to store.
Screen Size
Screen width (Width)
F: Increases width.
E: Reduces width.
Screen height (Height)
C: Increases height.
D: Reduces height.
Press 
< to store.
POSITION/SIZE Menu screen
“Position” adjustment screen
“Size” adjustment screen
01_E_7473.bo ok  22 ページ  ２００６年 ９月６日　水曜日　午後２時３６分
 
						

							
E-23
English
Deutsch
Espa
ñol
Fran
çais
Italiano
Portugu
ês
日 本 語
Póññêèé
中文
ADJUSTING AUDIO
• You can make changes to all audio adjustment options in the AUDIO Menu. See Page E-19 for the basic operation procedures.
• The changes you make will be stored for the  selected input mode.  Therefore, you need to select a desired input mode before ma king any 
changes.
• When the optional speaker is not  installed, sound is not output.
Treble
Press EF to make adjustments.
F: Stronger treble
E: Weaker treble
Press 
< to store.
Bass
Press EF to make adjustments.
F: Stronger bass
E: Weaker bass
Press 
< to store.
Balance
Press EF to make adjustments.
F: Shifts the volume balance towards the right.
E: Shifts the volume balance towards the left.
Press 
< to store.
Loudness
Corrects the balance between bass and treble  for easy listening even with weak volume.
Each time you press 
E or F, one of the available choices  appears in the following sequence:
<
 On < Off <
Press 
< to store.
AUDIO Menu screen
Note
• The screen display disappears if there is no  operation within approximately 60 seconds.
• Depending on the model or the optional devices,  some of the functions may not be available.
• The adjustment range varies according to  the display signals. Make adjustments to your preferred picture quality within the adjustment range.
• Depending on the type of signal, it may not be po ssible to make some of the settings or adjustments.
• AUDIO menu will not be displayed when  “No Audio” is selected. (See P. E-27.)
01_E_7473.book  23 ページ  ２００６年 ９月６日　水曜日　午後２時３６分
 
						

							
E-24
OTHER ADJUSTMENTS
FEATURES setup screen has the following 5 options.See Page E-19 for the basic operation procedures.
[Adjustment] : Can make a fine adjustment of pictur es such as Dot Clock, Clamp Position.
[On Screen Menu] : Can make a display setting such  as OSD, Language. (See P. E-24.)
[Input Terminal] : Can make an input terminal setti ng such as Video Input. (See P. E-25.)
[Channel Setting] : Can make channel sett ings. (See P. E-26.)
[Others] : Used to make Screen Orbiter  and other settings. (See P. E-27–E-28.)
Dot Clock, Clock Phase, Clamp Position, and Auto Calibration are adjusted as shown in the following chart.
Select the item with 
CD , and then adjust with E F. Finally, press < to implement the adjustments.
On-screen display Information (OSD)
You can use this option to select  whether to display information.
Each time you press 
E or F, one of the available choices  appears in the following sequence:
<
 On (OSD:bright) < On (OSD:dark) <
[On (OSD:bright)] :  On-screen information shown in light color.
[On (OSD:dark)] :  On-screen information shown in dark color.
Press 
< to store.
* If the screen picture is too bright, some characters  may be difficult to watch when [On (OSD:dark)] is 
selected.
Language (Language)
You can use this option to select th e language displayed on the screen.
(1) Select “Language” and press 

						

							
E-25
English
Deutsch
Espa
ñol
Fran
çais
Italiano
Portugu
ês
日 本 語
Póññêèé
中文
Name Selection (Name Select)
You can change the settings for indications for video inputs and RGB inputs.
Video input You can change the se ttings for indications for the VIDEO inputs.
Select the desired indication in acco rdance with the connected equipment.
Each time
 E F is pressed, the setting is switched. (In the case of VIDEO1)
<
 Video1 < DVD1 < DVD2 < VCR1 < VCR2 < GAME < Camcorder < STB < Satellite < Cable TV <
Press 
< to store.
RGB input You can change the settings fo r indications for the RGB inputs.
Select the desired indication in accordance with the connected equipment.
Each time 
E F is pressed, the setting is switched. (In the case of RGB 1)
<
 RGB1  < PC1 < PC2 < DVD1 < DVD2 < STB < Satellite < Cable TV <
Press 
< to store.
Video1 or Video2 Input terminal
Function
Select the video input format.
Each time 
E F is pressed, the  setting is switched.
<
 Auto < Video  < S-video < RGB < 
Select the desired input.
[Auto] : Automatically selects Video and RGB.
Press 
< to store.
Video Format
You can use this option to select the vide o format appropriate for the input signal.
Each time you press 
E or F, one of the available modes a ppears in the following sequence:
<
 Auto1 < Auto2 < NTSC < PA L < SECAM < PA L 6 0 < N-PAL  < M-PAL < 4.43NTSC < 
[Auto1] :  Automatically selects NTSC, PAL and SECAM.
[Auto2] :  Automatically selects NTSC and M-PAL.
[Other than Auto] :  You need to select a system  appropriate to the input signal.
Press 
< to store.
D-SUB Input terminal
You can use this option to select the signal system it will receive to D-SUB Input terminal.
(1) Select D-SUB Input and press 

						

							E-26
OTHER ADJUSTMENTS (Continued)
Press C or D to select the items for setting. It is switched as shown as below.
Auto Store < Manual Store < Sort
Press 
< to proceed to the next step.
Auto Store
Press E or F to select the country or region, and then press 
						

							E-27
English
Deutsch
Espa
ñol
Fran
çais
Italiano
Portugu
ês
日 本 語
Póññêèé
中文
Auto Off-NO SIG.
You can make to the standby state automatically when the no signal state continued during set up time.
Press 
C D to select the “Time”.
Press 
E F to select the amount of time before the standby state starts.
<
 Off < 1 min. < 15 min. < 45 min. < 60 min. 
						

							E-28
OTHER ADJUSTMENTS (Continued)
(6) Press < to store.
* When the Screen Orbiter function is operated, some letters at the top, bottom, right or left of the screen may be missed.
Direct Settingfor RGB
You can use this option to switch the setting for RGB input signal.
Each time you press 
E or F, one of the available choices appears in the following sequence:
<
 Auto < VGA < WVGA < 480P < XGA < WXGA < SXGA < SXGA+ <
[Auto]:  The optimum display is obtained automatically for input signals.
[Others]:  The optimum resolution setting is fixed for each signal.
Press 
< to store.
* In Auto mode, the resolution of VGA, WVGA, 480P, XGA, WXGA, SXGA and SXGA
+ may not be automatically distinguished. 
Switch to the fixed display when the image is not displayed properly.
* Signals that are not applicable depending on the model or input terminals may not be displayed.
Code Settingfor RGB
Normally, use this option in Auto mode.
White Screen
You can use this option to display white over the entire screen to minimize phosphor burn-in.
Each time you press 
E or F, one of the available choices appears in the following sequence:
<
 Off < On <
Press 
< to store.
Background
When the screen size was set to “Normal”, to reduce “burn-in”, the brightness of the part at which left and right images are not displayed 
can be set. Normally, we recommend that “Light Gray” be used.
Each time you press 
E or F, the settings is switched.
< Black < Dark Gray < Light Gray <
Press 
< to store.
* Burn-in can still occur if the Normal mode is shown for extended periods.
Information
Displays system operation status.
Select “Information” and press 

						

							E-29
English
Deutsch
Espa
ñol
Fran
çais
Italiano
Portugu
ês
日 本 語
Póññêèé
中文
INITIALIZATION OF USER ADJUSTMENT VALUE
You can restore the values of the adjustment/setting made in the MENU to factory settings.
1
Press ;.
The main menu screen will appear.
2
Press E or F to select “FACTORY 
DEFAULT”.
Each time you press E or F, one of the available 
menus appears in the following sequence:
PICTURE < POSITION/SIZE < AUDIO < FEATURES 
< FACTORY DEFAULT
The FACTORY DEFAULT Menu screen will appear.
3
Press 
						

							E-30
OPTIONS
* When installing an option, make sure that all installation requirements for that option (as given in the relevant instruction manual) are met.
* The colors of options do not match the display colors perfectly.
* To improve the function and performance of optional accessories, specifications and part names may change. Consult your local dealer 
before purchasing.  Wall-mounting Bracket 0° to 15° mounting angle  P-WB4201 (for 42” model/50” model)
Ceiling unit  5° to 25° mounting angle  P-CT4200 (for 42” model/50” model)
Desktop Stand unit  P-TT4202 (for 42” model/50” model)
Speaker 
(1 set of 2 speakers) P-SP1000 (for attaching to the display) for 
42” model/50” model
P-SP4200 (for mounting on the speaker 
stands) for 42” model
P-SP5010 (for mounting on the speaker 
stands) for 50” model
Desktop Speaker Stand 
(1 set of 2 speaker stands)P-ST4200 (for P-SP4200)
P-ST5000 (for P-SP5010)
Warning 
To prevent injury, fire, and electric shock, arrange for options to be initially installed (or installed at a different location) by your dealer. 
CAUTION
This display (P42HTA51/P50XTA51) is for use only with Fujitsu General Limiteds option (P-WB4201, P-CT4200, P-TT4202). 
Using this display with other option can cause instability resulting in possible injury.
Frame
Screw A Spacer B
Spacer provided as an acsessoryTo install this plasma display with the wall-mounting bracket 
or the ceiling unit , install the accessory spacers between the 
plasma display and frame as shown in the figure at right.
For details, see the wall-mounting bracket installation 
manual or the ceiling unit installation manual.
01_E_7473.book  30 ページ  ２００６年９月６日　水曜日　午後２時３６分