Getnet Router GR-524WA User Manual

 3
1.2. Minimum Requirements 
The following devices are necessary to configure and use the ADSL2+ Router: 
• A PC with Pre-installed Ethernet Adapter (Required) and a Web-
Browser (Internet Explorer 4.0 or higher) 
• RJ-45 Ethernet crossover cable (Included in the package) 
• RJ-11 (ADSL Ready) phone Line 
 
1.3. Package Content 
• One ADSL2+ Router (Annex A or B) with antenna 
• One Power Adapter (12VDC, 1A) 
• One RJ-45 Ethernet Cable (100 cm) 
• One RJ-11 Telephone Line (180 cm) 
• One Quick...

 4
Power  Please plug the power adapter attached with the ADSL 
Router to the power jack. The power adapter is 12VDC, 1A. 
 
 
 
1.4.2. Front LEDs 
On the router’s front panel there are LED lights that inform you of the router’s 
current status. Below is an explanation of each LED and its description. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
LED Light Status Description 
On  Router is switched on and correctly 
powered. POWER (Green) 
  
On 
Off Wireless LAN WPS is on. 
Wireless LAN is disabled 
Blinking  Wireless...

 5
2. Hardware Installation 
Step 1. Connect the ADSL Line 
Use the supplied RJ-11 telephone cable, connect the router from the ADSL 
port to your telephone socket with an ADSL micro filter plugged in. 
 
Step 2. Connect the router to your LAN network 
Connect the router to your PC, hub or switch by attached the Ethernet cable 
to the LAN port of the router.  
 
 
 
Step 3. Connect the Power Adapter to the Router 
Connect the power adapter to the power jack on the rear panel of the router 
and switch on...

 6
3. Setup Wizard 
3.1. Getting Started 
Before you start, please check the following items: 
1.  Please make sure that you have connected the ADSL cable to the router 
correctly. When the ADSL cable is worked normally, the ADSL LED will be 
on. 
2.  Uninstall all of dial up programs if you have installed previously for the 
USB modem or other dial up devices. 
3.  It is recommended to configure the router through the Ethernet cable 
before you have set the wireless functions correctly. 
 
This wizard...

 7
3.2.  Automatically Set ISP 
You can configure the router by running the Setup Wizard in the CD-ROM 
provided in the package. The wizard provides quick setup for the Internet 
connection, SSID, wireless security, firmware upgrade and changing router’s 
password. When you start the Setup Wizard, you will get the following 
Welcome screen. Please choose the language to start with and follow the 
easy steps in the Wizard. No instruction for the Setup Wizard is given here. 
 
If you lost the CD-ROM or you...

 8
 
 
 
 
  

 9  
 
 
Please choose the product type which you bought . 
 
 
The default password is “ admin “ .  

 10
 
Please select your country and ISP .If the country or ISP is not listed , please 
select “Others” from the list.  
 
 
Click” Next “ to finish all configurations of Internet Connection , Wireless 
setting and Firmware Upgrade .  
  

 11
3.3. Manually Set ISP 
If you cannot find the ISP from the wizard, please follow the procedures below 
to set the ISP settings manually. 
 
Before configuring the ISP manually, please check with your ISP (Internet 
Service Provider) what kind of the service is provided such as PPPoE, PPPoA 
or RFC1483/2684. Gather the information as illustrated in the following table 
and keep it for reference. 
 
PPPoE VPI/VCI, VC-based/LLC-based multiplexing, Username, 
Password (and Service Name). 
PPPoA VPI/VCI,...

 12