GGP Italy SPA Lawn Mower 102-122 Instructions Manual

– take off the grass-catcher or stone-guard;
– remove the accumulated cuttings, reaching them from the exit of the collector
channel.
This job must only be performed with the engine turned
off.
5.4.8 E
ND OF MOWING
When you have finished mowing, disengage the blades, lower the engine speed
and ride the machine with the cutting deck in the highest position.
5.4.9 E
ND OF WORK
Stop the machine, put the accelerator lever in the
«SLOW» position and turn off the engine by putting
the key into the «OFF»...

gent, taking care not to wet the engine, the electrical parts or the electronic card
located under the dashboard.
Never use hose-nozzles or harsh detergents for cleaning the
body and engine!
For washing the inside of the cutting deck
and the collector channel the machine must
be on firm ground with:
– the grass-catcher or stone-guard fitted;
– the operator seated;
– the engine running;
– the transmission in neutral;
– the blades engaged.
Connect a water hose to each of the pipe fittings (1) one at a...

Carefully remove any dry grass
cuttings which may have collected around the
engine or silencer to prevent their catching fire
the next time the machine is used!
Empty the fuel tank by disconnecting the tube situated
at the inlet of the fuel filter (1) and follow the instruc-
tions in the engine manual.
The battery must be kept in a cool and dry place. Before a
long storage period (more than 1 month), always charge the battery, and then
recharge before using again (
☛6.2.5).
The next time the machine is...

litres of fuel left in the tank, which is enough for 30-40 minutes of normal work.
If, while running:
– the battery warning light comes on (
☛4.7.g): see chapter 7 of this manual.
– the oil warning light comes on (
☛4.7.e) (  if fitted): this means that there
is not enough lubrication and so the engine must be stopped immediately.
5.4.13 S
UMMARY OF THE MAIN ACTIONS TO BE CARRIED OUT WHEN USING THE MACHINE
➤
IMPORTANT
EN 33 HOW TO USE THE MACHINE
To ...
Start the engine (☛5.4.1)
Go forward (☛5.4.2)
Brake...

EN 34HOW TO USE THE MACHINE
5.5 USING ON SLOPING GROUND
Only mowing in any case on the maxi-
mum gradients already mentioned (max
10° - 17%), lawns on a slope have to be
mowed moving up and down and never
across them, taking great care when
changing direction that the highest
wheels do not hit obstacles (such as
stones, branches, roots, etc.) that may
cause the machine to slide sideways, tip
over or otherwise cause loss of control.
REDUCE SPEED BEFORE ANY CHANGE OF DIRECTION
ON SLOPES, and always engage...

must never be lifted by rope and tackle. While being transported, close
the fuel stopcock(  if fitted), lower the cutting deck, engage the parking
brake and fasten the machine securely with ropes or chains to the haul-
ing device.
5.7 ADVICE ON HOW TO OBTAIN A GOOD CUT
1. To keep a lawn green and soft with a good appearance it should be cut regu-
larly and without damaging the grass.
2. It is always better to cut the grass when dry.
3.The blades must be in good condition and well sharpened so that the...

EN 36MAINTENANCE
6. MAINTENANCE
6.1 SAFETY RECOMMENDATIONS
Before cleaning, maintenance or repair work, take out
the ignition key and read the relevant instructions. Wear suitable clothing
and strong gloves when dismantling and refitting the blades and in all
other hazardous situations for hands.
Never use the machine with worn or damaged parts.
Faulty or worn-out parts must always be replaced and not repaired. Only
use genuine spare parts: those that are not of an equivalent quality may
damage the...

EN 37 MAINTENANCE
6.2 PERIODIC  MAINTENANCE
6.2.1
MAINTENANCE AND GENERAL LUBRICATION
Follow the diagrams which show the points requiring checks, lubricating and
routine maintenance, together with the type of lubricant to be used and the fre-
quency required.
a) Periodic maintenance(☛6.2.2)
100502510
1.9
1.10
1.11
1.7
1.13
1.5
1.1
1.1
21)
1.2
1.2
1.3
1.12
HOURS 

EN 38MAINTENANCE
b) Lubrification
For mechanical drive models:
➤
GREASE OIL - SAE 30
For hydrostatic drive models:➤ 

EN 39 MAINTENANCE
6.2.2 GUIDE TO SCHEDULED MAINTENANCE
This table is to help you maintain your machine’s safety and performance. It
shows the main maintenance and lubrication work, indicating the frequency with
which it should be carried out. To the right of each item there is a box where you
write the date or after how many hours of operation the work was carried out.
WORKHOURSDONE(DAT E O RN°OFHOURS)
1. MACHINE
1.1Check of tight fixing and sharpness of blades25
1.2Blade replacement 100
1.3Check the...