GIGABYTE Gak8vm800m User Manual

Hardware Installation - 11 -
EnglishOn-Board SATA RAIDŠBuilt in VT8237R
ŠSupports Disk striping (RAID0) or DISK Mirroring (RAID1)
ŠSupports UDMA up to 150 MB/sec
ŠUp to 2 SATA Device
Hardware MonitorŠSystem voltage detection
ŠCPU temperature detection
ŠCPU / System fan speed detection
ŠCPU fan failure warning
BIOSŠUse of licensed AWARD BIOS
ŠSupports Q-Flash
Additional FeaturesŠSupports @BIOS
ŠSupports EasyTune  (Note 3)
OverclockingŠOver Clock (CPU) by BIOS
ŠOver Voltage (CPU/AGP) by BIOS
Form...

GA-K8VM800M Motherboard - 12 -
English
1-3 Installation of the CPU and Heatsink
Before installing the CPU, please comply with the following conditions:
1. Please make sure that the motherboard supports the CPU.
2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong
direction, the CPU will not insert properly.  If this occurs, please change the insert direction
of the CPU.
3. Please add an even layer of heat sink paste between the CPU and heatsink.
4. Please make...

Hardware Installation - 13 -
English1-3-2 Installation of the Heatsink
The heat sink may adhere to the CPU as a result of hardening of the heat sink paste. To prevent
such an occurrence, it is suggested that either thermal tape rather than heat sink paste be used for
heat dissipation or using extreme care when removing the heat sink.
Fig.1
Before installing the heat sink, please first add an even layer of heat sink
paste on the surface of the CPU. Install all the heat sink components (Please
refer to the...

GA-K8VM800M Motherboard - 14 -
English
Before installing the memory modules, please comply with the following conditions:
1. Please make sure that the memory used is supported by the motherboard.  It is
recommended that memory of similar capacity, specifications and brand be used.
2. Before installing or removing memory modules, please make sure that the computer power
is switched off to prevent hardware damage.
3. Memory modules have a foolproof insertion design. A memory module can be installed in
only...

Hardware Installation - 15 -
English1-5 Installation of Expansion Cards
You can install your expansion card by following the steps outlined below:
1. Read the related expansion cards instruction document before install the expansion card into the
computer.
2. Remove your computers chassis cover, screws and slot bracket from the computer.
3. Press the expansion card firmly into expansion slot in motherboard.
4. Be sure the metal contacts on the card are indeed seated in the slot.
5. Replace the screw to...

GA-K8VM800M Motherboard - 16 -
English
1-6 I/O Back Panel Introduction
PS/2 Keyboard and PS/2 Mouse Connector
To install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard to the
lower port (purple).
USB port
Before you connect your device(s) into USB connector(s), please make sure your device(s) such as
USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface. Also make sure
your OS supports USB controller. If your OS does not support USB...

Hardware Installation - 17 -
English1-7 Connectors Introduction
1) ATX_12V
2) ATX (Power Connector)
3) CPU_FAN
4) SYS_FAN
5) FDD
6) IDE1 / IDE2
7) SATA0 / SATA1
8) F_PANEL
9) PWR_LED
10) F_AUDO
11) CD_IN
12) SPDIF_IO
13) F_USB1 / F_USB2
14) IR
15) COMB
16) CLR_CMOS
17) BAT
3
12
8
16
13
17
155
4 6
7
912
11
14
10 

GA-K8VM800M Motherboard - 18 -
English
1/2) ATX_12V / ATX (Power Connector)
With the use of the power connector, the power supply can supply enough stable power to all the
components on the motherboard. Before connecting the power connector, please make sure that all
components and devices are properly installed.  Align the power connector with its proper location on
the motherboard and connect tightly.
The ATX_12V power connector mainly supplies power to the CPU. If the ATX_12V power
 connector is not...

Hardware Installation - 19 -
English3/4) CPU_FAN / SYS_FAN (Cooler Fan Power Connector)
The cooler fan power connector supplies a +12V power voltage via a 3-pin power connector and
possesses a foolproof connection design.
Most coolers are designed with color-coded power connector wires. A red power connector wire
indicates a positive connection and requires a +12V power voltage. The black connector wire is the
ground wire (GND).
Please remember to connect the power to the cooler to prevent system...

GA-K8VM800M Motherboard - 20 -
English
6) IDE1 / IDE2 (IDE Connector)
An IDE device connects to the computer via an IDE connector. One IDE connector can connect to one
IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical drive). If
you wish to connect two IDE devices, please set the jumper on one IDE device as Master and the other
as Slave (for information on settings, please refer to the instructions located on the IDE device).
7) SATA0 / SATA1 (Serial ATA...