Hitachi 26ld9000ta Users Manual

11
ENGLISH
COMPONENT NAMES (Continued) 
Remote Control 
1. Power ON/OFF 
2.  [Color (Red, Green, Yellow, Blue)] 
3.  TV Select (TV) 
Press this button to change input to TV.
4.  Input Select (AV1/AV2/AV3/AV4/HDMI/RGB) 
Press this button to change input mode.
5. Program Select  
Press these buttons to select a TV program directly.   
6. Freeze [Hold] 
Press this button to change the picture to freeze mode.
7. MENU 
8. Cursor 
9. Volume Up/Down 
10. MUTE 
11. [Index] 
12. Picture  Size 
Press this button...

12
PREPARATION 
Remote Control Batteries Installation 
This remote control operates on 2 “AA” batteries. 
1.  Open the battery compartment cover. 

”Slide opens the battery compartment cover on the backside of the remote 
control in the direction of an arrow.   
2.  Installing the batteries. 

”Install 2 “AA” batteries (included) making sure the polarities match the 
indication inside the compartment. 
3.  Close the battery compartment cover. 

”To close the battery compartment cover, slide the cover in...

13
ENGLISH
PREPARATION(continued) 
Safety Precaution on Main Unit Installation 
Read SAFETY PRECAUTIONS (4to 7) carefully besides this page.   
The Desktop Stand has been used for the illustration in this manual.   
When installing the main unit, be sure to use the specified mount units in order to obtain maximum performance and 
maintain the safety.   
We assume no responsibility or liability for personal injuries or property damages caused by use of other mount units or 
improper installation.   
As...

14
CONNECTION
Ter minal Positions 
Rear  
1.  Power Cord Socket 
2. Aerial Socket 
3. AV1 
4. AV3 
5. AV4  
6.  Monitor Out and Sub Woofer 
7. RGB  
8. HDMI 
Side 
9. AV2 
10. Headphone output 
Connecting Procedure 
Your television is ready for various kinds of connections. Make a connection in the following steps. Be sure to turn off the 
Main Power first when connecting external equipments.   
1. Connect Power Cord to the rear panel.   
2. Connect Aerial Lead.   
3. Connect your external equipments to...

15
ENGLISH
CONNECTION (continued) 
Connecting Procedure (continued) 
3. Connecting to External Equipment   

”Terminals on Rear   
AV 1 can be connected to the equipment with an S-Video output and Composite output. 
If your external device has a S-video terminal, S-VIDEO connection is recommended for higher quality picture. 
AV3 and AV4 can be connected to the equipment with Component output.
If your external device has a Component terminal, COMPONENT connection is recommended for higher quality...

16
CONNECTION (continued) 
Connecting Procedure (continued) 
Monitor Out can be used to display same image as main unit on another television. 
When this output terminal is connected to an external television with a 75 Ohm terminal, the same image from composite 
(AV1, AV2), or RF signal can be displayed to the external television.
Sub Woofer terminal can bring the deep bass sound from the external speaker.
PC terminal (D-sub 15 pin or audio) is connected to PC, which allows Analog RGB signal.
IN OUT...

17
ENGLISH
CONNECTION (continued) 
Connecting Procedure (continued) 
HDMI terminals can be connected to the devices with HDMI output. 
Information
HDMI(High Definition Multimedia Interface) is next-generation multimedia I/O interface. Only one cable is used to 
transmit all video/audio/control signals, which creates easy connection.   
Moreover, those digital signals can produce high quality data without any degradation.   
If your external device has a HDMI terminal, HDMI connection is recommended for...

18
CONNECTION (continued) 
Connecting Procedure (continued) 
Headphone The detail settings can be adjusted from Audio Menu on page29.
The audio from the speaker will be muted when connecting the headphone to this terminal.   
4. Connecting the plug into the wall socket 
Connect the Power Cord after completing all other connections. 
(The type of plug is different from this drawing for some 
countries.)  
(1)  Connect the power cord to this device. 
(2)  Fix the power cord cable to the clamp. 
(3)...

19
ENGLISH
BASIC OPERATION 
POWER On/Off 
Now, turn On the main power of the unit. Make sure that the Power Cord 
has plugged into the wall socket.   

”To turn On the power of  the television:   
1. Press the Main Power switch on the television.   

”  The Indicating Lamp will illuminates in Red (Standby mode).   
2. Press Sub Power button either on the control panel or on the remote 
control.  

”  The color of the Indicating Lamp turns into Green, and the image 
will display on the screen.   
Sub...

20
!
BASIC OPERATION (continued) 
Vo l u m e  UP/D OW N 
1. To increase the sound volume, press   button on the remote 
control, or Volume Up button on the control panel. 

” The Volume Indicator value on the screen will shift right.   
2. To decrease the sound volume, press 
  button on the remote 
control or Volume Down button on the control panel.   

” The Volume Indicator value on the screen will shift left.   
!
Vo l u m e  U p / D o w n  
button Mute button 
Mute
1. To mute the sound, press button...