Hitachi Storage Navigator Modular 2 User Guide

Preinstallation Information2–15
Hitachi Storage Navigator Modular 2 User’s Guide
2. Open the kernel parameters setting file /etc/system with a text editor 
and add the following text lines to the bottom of the file. For information 
about maximum values permitted, refer to the manual for your 
operating system.
 
3. Reboot the Solaris host and install Navigator 2.
Setting Solaris v10 kernel parameters
When installing Navigator 2 on a management console running Solaris v10, 
set the Solaris kernel...

2–16Preinstallation Information
Hitachi Storage Navigator Modular 2 User’s Guide
The console displays the following output.
Hitachi Storage Command Suite common component 
considerations
Before installing Navigator 2, be sure no products other than Hitachi 
Storage Command Suite Common Component are using port numbers 
1099, 23015 to 23018, 23032, and 45001 to 49000. If other products are 
using these ports, you cannot start Navigator 2, even if the Navigator 2 
installation completes without errors.
If...

Installing Navigator 23–1
Hitachi Storage Navigator Modular 2 User’s Guide
3
Installing Navigator 2
After ensuring that your configuration meets the system 
requirements described in the previous chapter, use the 
instructions in this chapter to install the Navigator 2 software on 
your management console PC.
The topics covered in this chapter are:
ˆTypes of installations
ˆInstalling Navigator 2 

3–2Installing Navigator 2
Hitachi Storage Navigator Modular 2 User’s Guide
Types of installations
Navigator 2 supports two types of installations:
• Interactive installations — attended installation that displays graphical 
windows and requires user input.
• Silent installations — unattended installation using command-line 
parameters that do not require any user input.
This chapter describes the interactive installation procedure. For 
information about performing silent installations using CLI...

Installing Navigator 23–3
Hitachi Storage Navigator Modular 2 User’s Guide
3. Proceed to the appropriate section for the operating system running on 
your management console:
•  Microsoft Windows. See Installing Navigator 2 on a Windows 
operating system, below.
• Solaris. See Installing Navigator 2 on a Sun Solaris operating 
system on page 3-10.
•  Red Hat Enterprise Linux 4 and Red Hat Enterprise Linux 4 Linux. 
See Installing Navigator 2 on a Red Hat Linux operating system on 
page 3-11.
The...

3–4Installing Navigator 2
Hitachi Storage Navigator Modular 2 User’s Guide
Figure 3-1:  Navigator 2 Welcome Window
5. Click Next two times until the Choose Destination Location window 
appears. 

Installing Navigator 23–5
Hitachi Storage Navigator Modular 2 User’s Guide
Figure 3-2:  Choose Destination Location Window
6. Install Navigator 2 in the default destination folder shown or click the 
Browse button to select a different destination folder. 
7. Click Next. The Input the IP address and port number of the PC window 
appears.
If youNOTE:If you select a different destination folder, see Selecting a 
destination folder on page 2-12. 

3–6Installing Navigator 2
Hitachi Storage Navigator Modular 2 User’s Guide
Figure 3-3:  Input the IP Address and Port Number of the PC Window
8. Enter the following information:
• IP Addr. Enter the IP address or host name used to access 
Navigator 2 from your browser. Do not specify 127.0.0.1 and 
localhost.
• Port No. Enter the port number used to access Navigator 2 from 
your browser. The default port number is 1099.
9. Click Next. The Start Copying Files window shows the installation 
settings you...

Installing Navigator 23–7
Hitachi Storage Navigator Modular 2 User’s Guide
10. Review the settings to make sure they are correct. To change any, click 
Back until you return to the appropriate window, make the change, and 
click Next until you return to the Start Copying Files window.
11. In the Start Copying Files window, click Next to start the installation. 
During the installation, windows show the progress of the installation. 
When installation is complete, the InstallShield Wizard Complete window...

3–8Installing Navigator 2
Hitachi Storage Navigator Modular 2 User’s Guide
Figure 3-4:  InstallShield Wizard Complete Window
12. In the InstallShield Wizard Complete window, click Finish to complete 
the installation. Then proceed to Chapter 5, Quick Tour for a description 
of the Navigator 2 interface.
13. Proceed to Chapter 4, Starting Navigator 2 for instructions about logging 
in to Navigator 2.
If your Navigator 2 installation fails, see If the Installation Fails on a 
Windows Operating System on...