Honeywell 1202g2 Manual

3 - 9
Open Link Mode - Single Scanner
When newly shipped or defaulted to factory settings, a scanner is not linked to a base.  A link is established when the 
scanner is placed into a base.  When in Open Link Mode, a new link is established when a new scanner is placed in 
the base.  Each time a scanner is placed into a base, the scanner becomes the linked to the base and the old scanner 
is unlinked.
Unlinking the Scanner
If a base has a scanner linked to it, that scanner must be unlinked before a new...

3 - 10
Alarm Duration
To set the the length of time you want the Out-of-Range alarm to sound, scan the following bar code and then set the time-
out duration (from 0-3000 seconds) by scanning digits on the Programming Chart inside the back cover, then scanning 
Save.  Default = 1 sec.
Scanner Power Time-Out Timer
Note: Scanner Power Time-out Timer only applies to cordless systems.  It does not apply to corded scanners.
When there is no activity within a specified time period, the scanner enters low power...

3 - 11
Batch Mode
Batch mode is used to store bar code data when a scanner is out of range of its base, or when performing inventory.  The data 
is transmitted to the base once the scanner is back in range or when the records are manually transmitted. 
Note: Batch Mode is only supported by the Honeywell Charge and Communication Base (CCB) and Honeywell Access Point 
(AP). 
Automatic Batch Mode stores bar code data when the scanner is out of range of the base.  The data is automatically transmit-
ted to...

3 - 12
Batch Mode Quantity
When in Inventory Batch Mode (page 3-11), you may wish to transmit the number of multiple bar codes scanned, rather 
than a single bar code multiple times.  For example, if you scan three bar codes called XYZ with Batch Mode Quantity Off, 
when you transmit your data it will appear as XYZ three times.  Using Batch Mode Quantity On and the Quantity Codes 
(page 3-13), you could output your data as “00003, XYZ” instead.  Default = Batch Mode Quantity Off. 
Entering Quantities...

3 - 13
Delete Last Code
If you want to delete the last bar code scanned when in Batch Mode, scan Delete Last Code.
Record Counter
If you wish to add a record counter to each bar code scanned in Batch Mode, scan Record Counter On.  Your batch output 
would add a sequential number before each bar code, for example:
00001,bar code 1
00002,bar code 2
2
3
4
5
6
7
8
9
Delete Last Code 

3 - 14
Default = Record Counter Off.
Total Records
If you wish to output the total number of bar codes scanned when in Batch Mode, scan Total Records.  
Batch Mode Output Order
When batch data is transmitted, select whether you want that data sent as FIFO (first-in first-out), or LIFO (last-in first-out).  
Default = Batch Mode FIFO.  
Clear All Codes After Transmission
If you want to clear the scanner’s buffer of all data accumulated in Batch Mode after the data has been transmitted to the 
host system,...

3 - 15
Clear All Codes
If you want to clear the scanner’s buffer of all data accumulated in Batch Mode, scan Clear All Codes.
Transmit Records Automatically
If you are operating in Inventory Batch Mode (see Inventory Batch Mode on page 3-11), you can transmit all stored data to 
the host system when the scanner is placed in the base.  If you don’t want the records transmitted when the scanner is 
placed in the base, scan the Don’t Transmit Records Automatically bar code.  Default = Don’t Transmit Records...

3 - 16
Scanner Name
You may assign a name to each scanner you are using for identification purposes.  The default name is “Voyager.”   
Perform the rename operation using either the bar codes on page 3-17, or by sending the serial command :*:BT_NAMname. 
where name is the new name for the scanner.
To rename scanners with sequential, numeric names, scan the following bar codes.
  Scan the Reset code after each name 
change and wait for the scanner to relink to the base.
Batch Mode Transmit Delay Medium...

3 - 17
You may also scan the following Scanner Name bar code and scan up to 30 numbers and/or letters for the scanner name.  For 
example, if you wanted to name the linked scanner “312,” you would scan the following bar code, scan the 3, 1, and 2 bar codes 
on the Programming Chart inside the back cover of this manual, then scan Save.  Scan the Reset bar code and wait for the 
scanner to relink to the base.
To output the name of the scanner, scan the following bar code.  The name will be output showing...

3 - 18
The following table shows the results of the Auto Reconnect On and Off settings: 
Maximum Link Attempts
The Maximum Link Attempts setting controls the number of times the scanner tries to form a connection with a base.  
During the connection setup process, the scanner transmits in order to search for and connect to a base.  In order to pre-
vent continuous transmissions that could interfere with other users of the ISM band, the number of attempts to connect is 
limited by this setting.  After the...