Honeywell 1250g2 Manual

iii
Scanner-Bioptic Packet Mode ............................. 2-34
ACK/NAK............................................................. 2-34
Communication Timeout ..................................... 2-34
Chapter 3 -  Input/Output Settings
Power Up Beeper ........................................................ 3-1
Beep on BEL Character .............................................. 3-1
Good Read and Error Indicators ................................. 3-2
Beeper – Good Read...

iv
Deactivation Character ........................................ 3-15
Reread Delay ............................................................. 3-16
User-Specified Reread Delay .................................... 3-16
Output Sequence Overview ....................................... 3-16
Output Sequence Editor ...................................... 3-16
To Add an Output Sequence ............................... 3-17
Other Programming Selections ............................ 3-17
Output Sequence Editor...

v
Terminal ID Table ........................................................ 5-4
Data Format Editor Commands .................................. 5-4
Move Commands .................................................. 5-5
Search Commands................................................ 5-6
Miscellaneous Commands .................................... 5-7
Data Formatter ............................................................ 5-8
Data Format Non-Match Error Tone...................... 5-9
Primary/Alternate...

vi
EAN-13 Beginning with 290 Addenda Required .. 6-46
EAN-13 Beginning with 378/379 
Addenda Required ......................................... 6-47
EAN-13 Beginning with 414/419 
Addenda Required ......................................... 6-48
EAN-13 Beginning with 434/439 
Addenda Required ......................................... 6-48
EAN-13 Beginning with 977 Addenda Required .. 6-49
EAN-13 Beginning with 978 Addenda Required .. 6-49
EAN-13 Beginning with 979 Addenda Required .. 6-50
ISBN Translate...

vii
Chapter 9 -  Serial Programming Commands
Conventions ................................................................ 9-1
Menu Command Syntax .............................................. 9-1
Query Commands ....................................................... 9-2
Responses ............................................................ 9-3
Serial Trigger Commands ........................................... 9-4
Read Time-Out ...................................................... 9-4
Resetting the...

viii
ASCII Conversion Chart (Code Page 1252) ............... A-3
Lower ASCII Reference Table .................................... A-4
ISO 2022/ISO 646 Character Replacements.............. A-9
Unicode Key Maps.................................................... A-12 

1 - 1
1
Getting Started
About This Manual
This User’s Guide provides installation and programming instructions for the 
Voyager 1250g single-line laser scanner.  Product specifications, dimensions, 
warranty, and customer support information are also included.
Honeywell bar code scanners are factory programmed for the most common 
terminal and communications settings.  If you need to change these settings, 
programming is accomplished by scanning the bar codes in this guide.
An asterisk (*) next to an...

1 - 2
2. The scanner beeps.  
3. Verify the scanner operation by scanning a bar code from the Sample 
Symbols in the back of this manual.
The unit defaults to a USB PC Keyboard.  Refer to page 2-5 for other USB 
terminal settings.
For additional USB programming and technical information, refer to “USB 
Application Note,” available at www.honeywellaidc.com.
Connecting with Keyboard Wedge
A scanner can be connected between the keyboard and PC as a “keyboard 
wedge,” plugged into the serial port, or...

1 - 3
Connecting with RS232 Serial Port
1. Turn off power to the terminal/computer.
2. Connect the appropriate interface cable to the scanner.
3. Plug the serial connector into the serial port on your computer.  
Tighten the two screws to secure the connector to the port.
4. Once the scanner has been fully connected, power up the computer.
This interface programs 9600 baud, 8 data bits, no parity, and 1 stop bit. 
  
only if 
power 
supply is 
included 

1 - 4
Connecting with RS485
A scanner can be connected for an IBM POS terminal interface.
1. Connect the appropriate interface cable to the device, then to the com-
puter.
2. Turn the terminal/computer power back on.  The scanner beeps.
3. Verify the scanner operation by scanning a bar code from the Sample 
Symbols in the back of this manual.  The scanner beeps once.
For further RS485 settings, refer to RS485, page 2-2.