Honeywell control panel LYNXR2 User Manual

– 31 – 
USER FUNCTIONS
USER FUNCTIONSUSER FUNCTIONS USER FUNCTIONS 
    
Scheduling User Interface  
 
To access the Scheduling User Interface enter:                         + FUNCTION  + [64] 
  Master user code or  
 Installer Code 
 The following entries will be sequentially prompted to the user. Note that all inputs are checked for 
validity upon entry and all invalid entries are rejected. Hitting a [*] will allow the entries to be 
accepted and advance to the next field. Hitting a [#] will reject...

– 32 – 
USER FUNCTIONS
USER FUNCTIONSUSER FUNCTIONS USER FUNCTIONS 
    
Scheduling User Interface  
NOTE:  The keypad beeps twice for invalid data entries (e.g.: an hour greater than 12), and the entry will 
not be accepted. The keypad beeps once for valid entries and four times when a schedule event is 
programmed successfully. 
[x] = the value that was last stored in the memory. 
  
 x n 
Schedule number 
[x] = schedule number 1 to 8 
[*] = continue 
[#] = exit schedule programming 
mode...

– 33 – 
USER FUNCTIONS
USER FUNCTIONSUSER FUNCTIONS USER FUNCTIONS 
    
Scheduling User Interface 
  
 b :   xx 
Begin Time (minute) 
[xx] = begin minute 0 to 59 
[*] = continue 
[#] = return to previous prompt 
  
 
xx    :  bd 
Begin Day 
[xx] = begin day 01 to 17 
[*] = continue 
[#] = return to previous prompt 
 
 •  If  the value programmed in the Event Identifier is “3”, 
“4”, or “5”, and the current entry is completed, the 
system will save all field data up to this field. The 
system will beep...

– 34 – 
USER FUNCTIONS
USER FUNCTIONSUSER FUNCTIONS USER FUNCTIONS 
    
Scheduling User Interface  
 
Event Identifier Entries 
 
Note: On systems that are is equipped with a Wireless keypad, reminder announcements and the alarm 
clock will only be broadcast locally by the LYNXR-2 Series keypad. 
 
Entry Event Comment 
0  Empty  No event scheduled (or schedule is temporarily disabled) 
 
1  X10 Device  Turn an X10 device, either on or off at begin/end times. (will 
have a start and end time to program)...

– 35 – 
USER FUNCTIONS
USER FUNCTIONSUSER FUNCTIONS USER FUNCTIONS 
    
Scheduling User Interface 
 
Day of Week Entries 
 
 
Entry  
Day 
00  Invalid day entry  
01  Do event on next time match on the next Monday (will remove itself after executing)  
02  Do event on next time match on the next Tuesday (will remove itself after executing)  
03  Do event on next time match on the next Wednesday (will remove itself after executing)  
04  Do event on next time match on the next Thursday (will remove...

– 36 – 
USER FUNCTIONS
USER FUNCTIONSUSER FUNCTIONS USER FUNCTIONS 
    
Remote Phone Control Feature 
 
The LYNXR-Series  is equipped with a remote interactive phone capability that permits access to the 
security system from any off-site touch-tone telephone using all user codes. If this feature has been 
programmed, the system will provide the appropriate voice messages and any system beeping sounds 
indicating the status of the security system over the phone line. (Refer to Summary of Audible...

– 37 – 
USER FUNCTIONS
USER FUNCTIONSUSER FUNCTIONS USER FUNCTIONS 
    
Remote Phone Control Feature 
 
Enter:                        (within eight seconds) 
  Your user code 
Upon entering remote phone control mode the Lynx will announce “System, enter code”. 
Remote Phone Control Commands 
 
To remotely disarm system: 
                       + [1] 
  Your user code 
To remotely arm in AWAY mode:                        + [2] 
  Your user code 
To remotely arm in STAY mode:                        + [3]...

– 38 – 
USER FUNCTIONS
USER FUNCTIONSUSER FUNCTIONS USER FUNCTIONS 
    
Speaker Phone Feature 
 
If this feature has been programmed the LYNXR-2 Series is capable of operating as a speaker phone. 
During speaker phone operation the system will provide the following functions: 
• All function/event processing will continue to operate, but there will be no announcements. 
• The ARMED (red) and READY (green) LEDs will alternately blink. 
• “PH” will be displayed. 
NOTE:  The system will enter the Speaker...

– 39 – 
USER FUNCTIONS
USER FUNCTIONSUSER FUNCTIONS USER FUNCTIONS 
    
Speaker Phone Feature 
 
LYNXR-2 Series Speaker Phone Functions 
To place a call using the Speaker Phone:  
[#] + AUX and dial the desired phone number. 
To answer a call using the Speaker Phone: 
[#] + AUX  
To flash (switch between two calls using call waiting): 
AUX  
To hang up:  
OFF   
To activate/deactivate (toggle) ringer:  
[#] +  VOLUME  +  AUX  
To return the keypad to telephone mode after disarming the system: 
[#] + AUX...

– 40 – 
USER FUNCTIONS
USER FUNCTIONSUSER FUNCTIONS USER FUNCTIONS 
    
Remote Services 
 
Your security system may be capable of providing a series of web-based services that allow you to 
communicate with your security system remotely in a number of ways. These services provide the 
ability to: 
• Access to your security system from a computer via website (Remote Access Feature) 
• Receive e-mail and text message notification of system events (Multi-Mode Feature) 
• Perform system functions and...