Home > Honeywell > Keypad > Honeywell keypad 81328132i User Manual

Honeywell keypad 81328132i User Manual

Here you can view all the pages of manual Honeywell keypad 81328132i User Manual. The Honeywell manuals for Keypad are available online for free. You can easily download all the documents as PDF.

Page 51

Internet Features (Contd) 
51 
 
User Feedback 
User Feedback 
Name:  
  
Email Address:   
  
Type of Feedback  Suggestion 
  
Category  Symphony/Symphony-i W eb Interface – 
Custom Content 
 
 Other:  
  
Comment: 
(250 characters max.)  
 
 
 
 
 
Logout 
The LOGOUT button allows you to leave the http://Symphony.alarmnet.com 
Internet site.  Pressing the LOGOUT button displays the following:  
You have been logged out.   
Click Here to Close Your Browser 
  

Page 52

Internet Features (contd) 
52 
 
  
 
  

Page 53

 
53 
 
                                                 Advanced System Features 
 
Introduction to Advanced System Features 
While most of the commonly used security functions are available from 
Symphony/Symphony-i’s advanced user interface, there are some less used, 
advanced features that can either be accessed through Keypad Emulation mode on 
the Symphony/Symphony-i or a standard Alpha Keypad.  To program your system’s 
advanced features, refer to your Control Panel User Guide. 
Keypad (Console)...

Page 54

Trouble Conditions (Contd) 
54 
 SCREEN ACTION 
 3.  Press the Console Mode button on the 
More Choices screen.  The Keypad screen 
is displayed. 
 4.  Perform functions as you would from a 
regular alpha keypad.  

Page 55

 
55 
 
Summary of Audio Notification 
 
SOUND CAUSE  DISPLAY 
Loud, Interrupted* 
Keypad & External Fire Alarm  FIRE is displayed; descriptor of zone in 
alarm is displayed. 
Loud, Continuous* 
Keypad & External Burglary/Audible Emergency 
Alarm  ALARM is displayed; descriptor of zone in 
alarm is also displayed. 
One Short Beep 
(not repeated) 
Keypad only a.  System disarm   
b.  System arming attempt 
with an open zone. 
c.  Bypass verify  a.  DISARMED/READY TO ARM is 
displayed.  
b.  The number and...

Page 56

Summary of Audio Notification (Contd) 
56 
 
**  Entry warning may consist of three short beeps or slow continuous beeping, as 
programmed by your installer. 
***  Loss of system battery power is not indicated or annunciated by the Keypad 
(warnings are for loss of AC power only). 
  

Page 57

 
57 
 
Summary of Symphony/Symphony-i LED Operation 
Symphony/Symphony-i LED Operation 
Symphony/Symphony-i has four LEDs labeled - WEB, ARMED, READY and 
MESSAGE. WEB and MESSAGE LEDs are yellow. ARMED LED is red and 
READY LED is green. Each LEDs on and off state has different meanings during 
different operations.  
Following states use LEDs to represent different sub-states. 
• Normal (Idle) State 
• Software Download State 
• Software Download State - Failure Modes 
Each LED can have four different...

Page 58

Summary of Symphony/Symphony-i LED Operation (Contd) 
58 
 
LED Operation When Software Download Fails 
There are the following sequences providing the extra failure information: 
1.  CRC failure 1 (calculated CRC does not match CRC provided with binary) 
• WEB, ARMED, READY and MESSAGE – all FAST BLINK for 3 seconds, 
following 
• WEB, ARMED, READY and MESSAGE ON for 3 seconds and following  
• WEB, ARMED, READY and MESSAGE FAST BLINK for 3 seconds. 
2.  CRC failure 2 (calculated network CRC does not...

Page 59

 
59 
 
Symphony/Symphony-i Setup 
 
How to Access Symphony/Symphony-i Setup Options 
Setup allows you to adjust the touch screen contrast and/or adjust the 
Symphony/Symphony-i speaker volume.  You may also select the time interval that 
must pass prior to Symphony/Symphony-i going into screen saver mode (screen goes 
blank). Additionally, you may enter the User Setup screen, Advanced Setup 
screen, or Clean Screen (maintenance mode) from the Setup screen by pressing 
the corresponding button. 
How to...

Page 60

Symphony/Symphony-i Setup (contd) 
60 
 
How to Adjust the Touch Screen Contrast 
You may adjust the touch screen contrast as follows: 
If… Then… 
you want to increase contrast  move the slide bar above the current contrast 
setting. 
you want to decrease contrast  move the slide bar below the current contrast 
setting. 
another adjustment or selection is to be made  go to the corresponding paragraph in this 
section. 
no additional adjustment or selection is to be 
made press the Back icon at the...
Start reading Honeywell keypad 81328132i User Manual

Related Manuals for Honeywell keypad 81328132i User Manual

All Honeywell manuals