Honeywell keypad 81328132i User Manual

							Fire Alarm System Operation (Contd) 
31 
 
• Install a smoke detector at both ends of a hallway if the hallway is more than 40 
feet (12 meters) long. 
• Install smoke detectors in any room where an alarm control is located, or in any 
room where alarm control connections to an AC source or phone lines are made. 
If detectors are not so located, a fire within the room could prevent the control 
from reporting a fire or an intrusion. 
Recommendations For Proper Intrusion Protection 
For proper intrusion coverage, sensors should be located at every possible point of 
entry to a home or commercial premises. This would include any skylights that may 
be present, and the upper windows in a multi-level building. 
In addition, we recommend that radio backup be used in a security system so that 
alarm signals can still be sent to the alarm monitoring station in the event that the 
telephone lines are out of order (alarm signals are normally sent over the phone 
lines, if connected to an alarm monitoring station). 
Recommendations for Evacuation 
Establish and regularly practice a plan of escape in the event of fire. The following 
steps are recommended by the National Fire Protection Association: 
1.  Position your detector or your interior and/or exterior sounders so that they can 
be heard by all occupants. 
2.  Determine two means of escape from each room. One path of escape should lead 
to the door that permits normal exit from the building. The other may be a window, 
should your path be impassable. Station an escape ladder at such windows if there 
is a long drop to the ground. 
3.  Sketch a floor plan of the building. Show windows, doors, stairs and rooftops that 
can be used to escape. Indicate escape routes for each room. Keep these routes free 
from obstruction and post copies of the escape routes in every room. 
4.  Assure that all bedroom doors are shut while you are asleep. This will prevent 
deadly smoke from entering while you escape. 
5.  Try the door. If the door is hot, check your alternate escape route. If the door is 
cool, open it cautiously. Be prepared to slam the door if smoke or heat rushes in. 
6.  Where smoke is present, crawl on the ground; do not walk upright. Smoke rises 
and may overcome you. Clearer air is near the floor. 
7.  Escape quickly; dont panic.  
						

							Fire Alarm System Operation (contd) 
32 
 
8.  Establish a common meeting place outdoors, away from your house, where 
everyone can meet and then take steps to contact the authorities and account for 
those missing. Choose someone to assure that nobody returns to the house — many 
die going back. 
 
 
  
						

							 
33 
 
User Code Setup 
 
Introduction to User Code Setup 
Each user must be assigned a name with a corresponding 4-digit user code in order 
to gain access to various features and functions. Through Symphony/Symphony-i, 
you may program users to access each of the following systems: 
• Fire/Burglary 
• Internet 
Users for the systems are programmed in a central user setup location that provides 
the specific questions for the user pertaining to each system.  You may want these 
users to be the same, but there are situations in which you may want a user to have 
access to one system (e.g., Internet) without having access to another (e.g., the 
Fire/Burglary system).  
How to Access User Setup  
Access User Setup as follows: 
SCREEN   ACTION 
 1.  From the Home screen, press the “Tool 
Box” button.  The setup screen is displayed. 
 
 2.  Press the User Setup button on the “Setup” 
screen.  The User Setup screen is displayed. 
  
						

							User Code Setup (contd) 
34 
 SCREEN   ACTION 
 
  
						

							User Code Setup (Contd) 
35 
 
How to Add a User 
Add a user as follows: 
SCREEN   ACTION 
 1.  To add a use, press the Add User button.  
The User Authorization screen is displayed 
with the instructions Enter Authorized Code. 
 
 2.  Enter your “Master” code.  The “User 
Options” screen is displayed. 
 3.  Press the box next to Enter User Name.  
The Enter Data keyboard screen is displayed. 
 4.  Type in the user name and press the OK 
button.  The “User Options” screen is displayed 
with Enter user code… displayed.   
  
						

							User Code Setup (contd) 
36 
 SCREEN   ACTION 
 5.  Touch the box next to Enter user code.  
The User Authorization screen is displayed 
with the instructions Enter 4 Digits. 
 
 6.  Enter the 4-digit code for this user.  The 
“User Options” screen is displayed with the 
user’s name and code displayed.   
 
 
 7.  Select the partitions and access level for 
this user.  
NOTE:  If this user is to have Internet access, 
continue to step 8.  If this user is to have 
security access only, press the Save button at 
this time. 
 
 8.  Press the Web tab on the “User Options” 
screen.  The “Web access” screen is 
displayed.  
						

							User Code Setup (Contd) 
37 
 SCREEN   ACTION 
 9.  To provide this user with Internet access 
press the box next to Enable user for web 
access until a check appears.  You may also 
select the Autoswitch to web on disarm 
option at this time. 
 
 10.  Press the Save button.  The system will 
save the configuration.  W hen the save is 
complete, the User Setup screen is displayed 
with the new user’s name shown. 
 
 
  
						

							User Code Setup (contd) 
38 
 
How to Delete a User 
Delete a User as follows: 
SCREEN ACTION 
 1.  From the User Setup screen, touch the 
user to be deleted.  The user name is 
highlighted.  Press the Delete User button.  
The User Authorization screen is displayed 
with the instructions Enter Authorized Code. 
 2.  Enter your “Master” code.  The Delete 
screen is displayed. 
 3.  Press the appropriate button.  The User 
Setup screen is displayed. 
   
						

							User Code Setup (Contd) 
39 
 
How to Edit a User 
Edit a user as follows: 
SCREEN   ACTION 
 1.  From the User Setup screen, touch the 
user to be edited. The user name is 
highlighted. Press the Edit User button.  The 
User Authorization screen is displayed with 
the instructions Enter Authorized Code. 
 2.  Enter your “Master” code.  The “User 
Options” screen is displayed. 
 
 3.  Select whatever options you wish to select 
for this user and press the Save button.  The 
configuration changes are saved and you are 
returned to the User Setup screen.  
						

							User Code Setup (contd) 
40