HP Ac200 User Manual

							 
38 
7. Press both the video and photo buttons on your RF wrist strap 
remote control to process pairing. When the red LED on the RF 
wrist strap remote control flash once, pairing is complete. 
 
8. To exit the menu, press the Mode button 
repeatedly until the EXIT screen appears.   
9. Press the Shutter button to exit SET mode. 
4.13 Factory Default 
This menu allows you to restore the default factory settings of your 
camcorder. 
Do the following to restore the factory default settings. 
1. Press the Mode button repeatedly to change to SET mode. 
2. Press the Shutter button to enter SET mode. 
3. Press the Shutter button to enter the MORE menu.  
4. Press the Mode button to highlight DEFAULT.  
						

							 
39 
5. Press the Shutter button to enter the DEFAULT submenu. 
      
6. Press the Mode button to select √. 
 
7. Press the Shutter button to confirm. 
8. To exit the menu, press the Mode button 
repeatedly until the EXIT screen appears. 
9. Press the Shutter button to exit SET 
mode.  
 
  
						

							 
40 
5 Using the Accessories 
The camcorder comes with rugged accessories for all your sporting 
needs. 
5.1 Waterproof Case 
The waterproof case allows you to take underwater shots or use it with 
the surface mount, bike mount, or chest strap to capture other water 
sports activities. 
5.1.1 Using the Waterproof Case 
1. Release the case lock and flip open the waterproof case. 
 
2. Install the camcorder inside the waterproof case. 
  
						

							 
41 
3. Secure the waterproof case lock. 
 
The waterproof case can be used with other accessories such as the 
swivel T tip, bike mount, chest mount, head mount, etc. 
5.1.2 Changing the T Tip Adapter 
Depending on the accessories that you want to use with the case, the T 
tip adapter may be detached and attached to another housing back door 
or location. To detach the T tip adapter, remove the four screws securing 
each tip adapter to the case. 
  
						

							 
42 
5.1.3 Changing the Housing Back Door 
Depending on the accessories that you want to use with the case, you 
may need to change the housing back door. Two back doors are included 
in the standard package: the waterproof housing back door, and the 
vented housing back door. 
Do the following to change the housing back door: 
1. Open the back door 
completely. 
2. Pull to detach the back 
door from the case. 
3. Detach the T tip adapter 
from the current back 
door and install the T tip 
adapter to the back door 
you want to use. 
4. Install the back door. 
5.2 Velcro Strap 
The Velcro strap can be used to secure the waterproof case onto any 
object to conveniently record 
photos and videos.   
To install the Velcro strap, insert 
the strap through the strap 
holes of the tip adapter as 
shown below. 
 
 
  
						

							 
43 
5.3 Assembling the Camcorder Accessories 
Lock the T tip adapter to the T tip of the adjoining accessories to install 
them to your camcorder. 
  
						

							 
44 
5.4 RF Wrist Strap Remote Control 
Before using the RF wrist strap remote control, you must pair it with the 
camcorder. Take note that only one camcorder can be paired to the RF 
wrist strap remote control at a time. 
Do the following to pair your RF wrist strap remote control. 
1. On the camcorder, press the Mode button repeatedly to 
change to SET mode. 
2. Press the Shutter button to enter SET mode. 
3. Press the Shutter button to enter the MORE menu.  
4. Press the Mode button to highlight BINDING. 
5. Press the Shutter button to enter the BINDING submenu. 
      
6. The camcorder RF antenna is enabled and ready to be paired 
with the RF wrist strap remote control. 
 
7. On your RF wrist strap remote control, press both the Video 
and Photo buttons at the same time. When the red LED flash 
once, pairing is complete. 
 
8. Press the Video button to start and stop video recording. To 
take photos, press the Photo button.  
						

							 
45 
 Note 1: To take photos using burst mode, time lapse, or self-timer, 
switch to the respective mode on your camcorder and then press the 
Photo button on your RF wrist strap remote control. However, only 
one photo can be taken in time lapse mode when using the RF wrist 
strap remote control. 
 Note 2: Even if your camcorder is in Video mode, you can still take 
photos by pressing the Photo button on your RF wrist strap remote 
control. 
 Note 3: The maximum operation distance of the remote control is 
approximately 5m when the RF wrist strap remote control is pointed 
at the remote control sensor of the camcorder. 
  
						

							 
46 
Appendix 
Specifications 
General 
Imaging sensor  1/2.5” CMOS 5.0 Megapixel Sensor 
Active pixels  5.0 Megapixel 
Storage media  Internal: Built-in 256MB Flash Memory 
microSD Card, SDHC compatible (up to SDHC 
32GB Class6) 
Sensor sensitivity  Auto 
Camera Optics  Fixed lens 
Wide: F2.8, f=2.5mm 
110°/1080p, 150°/720p, 162°/960p,   
165°/ 5M Photo 
Focus range  30cm ~ infinity 
Still image  Format: JPEG (EXIF 2.2), DCF 
Resolution: 5M   
Mode: Signal shot 10 Photo Burst, Time-Lapse 
(every 1, 3, 5, 10, 30, 60 sec) 
Movie clips  Format: H.264 (MP4) 
Resolution: 1080p: 1920x1080 (30fps), 
960p: 1280x960 (30fps),   
720p: 1280x720 (60fps) 
Zoom NA 
Exposure Setting  Auto  
						

							 
47 
General 
EV Compensation  -2.0EV ~ +2.0EV (Auto) 
PC interface  USB 2.0 (High Speed) 
Wireless  IEEE 802.11 b/g/n 
TV out format  HDMI 
Shutter speed  Still: 1/30 ~ 1/4000 sec. 
Video: 1/30 ~ 1/2000 sec. 
Auto power off  1min / 3min / 5min / 10min / 30min / 60min / 
Off 
Power supply  Rechargeable 1130 mAh Li-ion Battery 
Dimensions  42.7 (H) x 59.2 (W) x 26.4 (D) mm   
(without lens) 
Weight 
Approx. 783g (without Waterproof Case)