HP Color LaserJet CP3525 User Manual

							CalloutArea on the screenInformation or capability that the area provides
Vivid (sRGB).This color theme is specifically for printing saturated
business graphics that you would like to have some extra “punch”. The
colors may be too saturated for photo imagery.
None.This color theme provides the user with access to the entire
devices range of colors. It enables an advanced user to do their own
color management.
Default CMYK +.A color theme by HP for CMYK source content that is
designed to provide a reasonable color rendering if the specific origin
(SWOP, EuroScale or DIC) of the CMYK content is not known.
SWOP. A color theme specifically designed to render CMYK content
according to the SWOP standard (a CMYK press Specification for Web
Offset Printing used in the USA).
Euroscale. A color theme specifically designed to render CMYK content
according to the Euroscale standard (a CMYK press specification
commonly used in Europe).
DIC (Dainippon Ink and Chemicals). A color theme specifically
designed to render CMYK content according to the DIC standard (a
CMYK press specification commonly used in Japan).
6Calibration InformationLists the last color-plane registration (CPR) page count, the last CPR
page-count date, the last page count (in engine cycles) for DMAX/
DHALF, and the last DMAX/DHALF page-count date.
Color plane registration occurs when new print cartridges are installed
to compensate for any slight variations that might occur in cartridge
circumference.
DMAX is a density calibration of each print cartridge color at 100%
coverage; DHALF is also a density calibration of each print cartridge
color, but as a halftone instead of a full color. During halftone printing,
the dots of toner are spread out, and coverage of the toner is less than
100%.
7MemoryLists the memory information, PCL Driver Work Space (DWS), and
resource saving information.
8Event LogLists the number of active entries in the Event Log, the 3 most recent
entries, and the Event Log total capacity.
9SecurityLists the status of the control-panel lock, disk write-protect options, and
direct-connect (USB or parallel) ports.
You can change the status of the Direct Connect ports on the Security
screen under the Settings tab by selecting or clearing the Disable
Direct Ports check box.
10Paper Trays and OptionsLists the size and type of media that is specified for each of the trays in
the product. If a duplexing unit or any paper-handling accessories are
installed on the product, information about those devices is also listed
here.
Table 2-2  Configuration Page (continued)
ENWWConfiguration Page 11
 
						

							Supplies Status Page
The Supplies Status screen shows more detailed supplies information and provides part numbers for
genuine HP supplies. (It is helpful to have the part numbers available when ordering supplies.) The
following illustration and table describe how to use this screen.
Figure 2-4  Supplies Status Page screen
1
2
3
Table 2-3  Supplies Status Page
CalloutArea on the screenInformation or capability that the area provides
1HP EWS tabs and menusFor more information, see Navigating through the HP Embedded Web
Server on page 4.
2Shop for Supplies linkUse this feature to connect to a Web page that facilitates online ordering of
supplies from a reseller of your choice.
3 Supply  Information If available, this lists the percent of life remaining and the estimated number
of pages remaining before the supply is empty; the total number of pages
that have been processed with the supply; the supply serial number and
HP part number; and an indication of whether or not the supply has reached
the low status.
12 Chapter 2   Viewing product status from the HP EWS Information screens ENWW
 
						

							CalloutArea on the screenInformation or capability that the area provides
If the Override at Out option has been enabled at the product control panel,
a message appears, when the supply is exhausted, stating that the
cartridge was used with the override setting.
NOTE:If a previously used or moved supply is used, information about
the device might not be available. In addition, a warning message about
the risks associated with using previously used or moved supplies could
appear on the screen. No further information about the status of the supply
will be available.
Table 2-3  Supplies Status Page (continued)
ENWWSupplies Status Page 13
 
						

							Event Log Page
The Event Log page screen shows the most recent product events, including jams, service errors, and
other printer errors. The following illustration and table describe how to use this screen.
Figure 2-5  Event Log Page screen
1
2
3
8
4567
Table 2-4  Event Log Page
CalloutArea on the screenInformation or capability that the area provides
1HP EWS tabs and menusFor more information, see Navigating through the HP Embedded Web Serveron page 4.
2NumberLists the order in which the errors occurred. The last error to occur has the
highest number.
3Date and TimeLists the date and time for each event logged.
4CyclesShows the number of engine cycles that the product had completed when the
error occurred. The product completes one engine cycle for every Letter/A4-
size page side that it prints or copies.
5EventShows the internal event code for each event.
6FirmwareDisplays the firmware version that was in place when the event occurred on
the printer.
7Description or PersonalityShows a brief description of some events.
8Product Support link Provides access to the HP support Web site for product-specific
troubleshooting information.
14 Chapter 2   Viewing product status from the HP EWS Information screens ENWW
 
						

							Usage Page
The Usage Page screen gives a page count for each media size that has passed through the product,
as well as the number of duplexed pages. The total is calculated by multiplying the sum of the print count
values by the Units value.
The information on this screen can be used to determine how much toner or paper to keep on hand.
The following illustration and table describe how to use this screen.
Figure 2-6  Usage Page screen (1 of 3)
1
3
2
4
ENWWUsage Page 15
 
						

							Figure 2-7  Usage Page screen (2 of 3)
5
16 Chapter 2   Viewing product status from the HP EWS Information screens ENWW
 
						

							Figure 2-8  Usage Page screen (3 of 3)
Table 2-5  Usage Page
CalloutArea on the screenInformation or capability that the area provides
1HP EWS tabs and menusFor more information, see Navigating through the HP Embedded Web
Server on page 4.
2Usage Totals (equivalent)Indicates the types of pages that have been printed, the number of single-
sided pages that have been printed, the number of duplexed pages that
have been printed, and the total number of pages that have been printed.
3UnitsA unit is equal to a standard A4-size (letter-size) page. All other page sizes
are referenced in relation to this standard size. An A4-size (letter-size) page
printed on both sides counts as 2 units.
4TotalTotal page counts for all types of printed media.
5Print Modes & Paper Path
Usage (actual)Indicates the different print modes that have been used for color and
monochrome (black-and-white) print jobs.
ENWWUsage Page 17
 
						

							Diagnostics Page
The Diagnostics Page screen provides information about calibration, color density, and parameters.
Figure 2-9  Diagnostics Page screen
1
2
3
4
Table 2-6  Diagnostics Page
CalloutArea on the screenInformation or capability that the area provides
1HP EWS tabs and
menusFor more information, see Navigating through the HP Embedded Web Server
on page 4.
2Calibration
InformationLists the last color-plane registration (CPR) page count, the last CPR page-count date,
the last page count (in engine cycles) for DMAX/DHALF, and the last DMAX/DHALF
page-count date.
Color plane registration occurs when new print cartridges are installed to compensate
for any slight variations that might occur in cartridge circumference.
DMAX is a density calibration of each print cartridge color at 100% coverage; DHALF
is also a density calibration of each print cartridge color, but as a halftone instead of
a full color. During halftone printing, the dots of toner are spread out, and coverage of
the toner is less than 100%.
18 Chapter 2   Viewing product status from the HP EWS Information screens ENWW
 
						

							CalloutArea on the screenInformation or capability that the area provides
3Color DensityLists the cyan, magenta, yellow, and black (CMYK) values for highlights, midtones,
and shadows.
4ParametersFor color devices, specific engine settings related to the printing or
electrophotographic process are critical in identifying device status and function. The
electrophotographic parameters, which are used to detect, diagnose, and track print-
quality defects, appear in a 272-cell binary array that contains the settings registered
by the device engine. These registers also appear at the bottom of the Diagnostics
Page screen.
Table 2-6  Diagnostics Page (continued)
ENWWDiagnostics Page 19
 
						

							Device Information
The Device Information screen shows the following information:
●Printer name
●Printer location
●Asset number
●Company name
●Contact person
●Product name
●Printer model
●Printer serial number
The product name, printer model, and printer serial number are automatically generated. You can
configure the other information on this screen from the Device Information screen on the Settings tab.
Figure 2-10  Device Information screen
20 Chapter 2   Viewing product status from the HP EWS Information screens ENWW